Alarm Configuration Options | Paradyne 317x E1 specs

ACCULINK 317x E1 DSU/CSU

Alarm Configuration Options

Table C-8

Alarm Configuration Options

Alrm Msg: Disab

Next Enab Disab Prev

Alarm Messages. Controls the generation of alarm messages, which are routed to an ASCII terminal or printer attached to the communication port. For more information, refer to the Alarms section in Chapter 4, Maintenance.

Enab ± Enables alarm messages routed to the communication port.

Disab ± Prevents alarm messages for any alarm conditions.

NOTE: Alarm messages are only sent to the communication port if the Com Use configuration option is set to ASCII, otherwise the alarm messages are discarded.

SNMP Trap: Disab

Next Enab Disab Prev

SNMP Trap Enable. Specifies whether SNMP trap messages are sent over the SNMP management link. For more information, refer to the SNMP Traps section in Chapter 4, Maintenance.

Enab ± Enables sending SNMP trap messages from this unit over any SNMP management link.

Disab ± Disables sending SNMP trap messages from this unit over any SNMP management link.

C-16

December 1996

3170-A2-GB20-20

Image 103

Paradyne 317x E1 manual Table C-8 Alarm Configuration Options, Alrm Msg Disab Next Enab Disab Prev

Contents

Channel Service Unit Copyright 1996 Paradyne Corporation. All rights reserved Warranty, Sales, and Service InformationTrademarks Operators Guide 3170-A2-GB20-20 Important Safety Instructions Acculink 317x E1 DSU/CSU Models 3172-A1-410 and 3174-A1-410 Only CE Marking Table of Contents Glossary Index Reference Documents PrefaceObjectives and Reader Assumptions Related Document Introduction FeaturesOverview Snmp Management Support Alarm Message CapabilityDTE Drop/Insert Interface Front Panel Emulation Rear Panel Physical DescriptionFront Panel Model 3172 Rear Panel Name Function Rear Panel Connectors and Switches Application Examples Installation Services Direct Connection to an Snmp Manager Snmp Connection Examples Connection through a LAN Adapter to Snmp Installing the +24 Vdc Power Supply Optional Power SourcesImportant Instructions 11. ±48 Vdc Single Source Power Supply Pinouts Installing the Single ±48 Vdc Power Supply 12. ±48 Vdc Redundant Source Power Supply Pinouts Installing the Redundant ±48 Vdc Power Supply 13. Cabling Examples Cabling Examples Self-Test Power-Up Self-TestSelf-Test Progress Self-Test Passed Operation E1 DSU/CSU Front Panel Using the Front Panel LCD Keypad LEDs Test Jacks Name Color Meaning System LEDsNetwork Interface LEDs PDV DTE Drop/Insert Port LEDs DTR Data Port LEDs Displaying Unit Identity ClrReg Control Reset CID DLTest Cnfig Ctrl Control Rel LED Display Test NetSig Displaying LED ConditionsStatus Perf TStat LED Select LEDs E1 Prt1 Prt2 Prt1 Prt2 Changing Configuration OptionsSelecting the DTE Drop/Insert or Data Port for LED Display LED Dsply DTE Edit DTE Port NET Displaying/Editing Configuration OptionsLoad from Activ Cust1 Choose Funct Edit Save Port Select Copy Prt1 Prt2 Saving Edit ChangesSelecting/Copying to a Specific Port Save Edit to Activ Cust1 Selecting the Port Configuring the E1 DSU/CSU for Snmp Management Setting the IP Address 010.155.111.222 Up Down Save Selecting the Link Layer ProtocolCom Link Next PPP Slip CommunityName1 Next Edit Clear Specifying the Community Names and Access TypesPublic Up Down Save Snmp Trap Next Enab Disab Configuring Snmp TrapsAccess Next Read R/W Enabling Snmp Trap Messages Trapn Dst Next None Com Configuring a Destination for Snmp TrapsSelecting the Number of Trap Managers Num Trap Mgrs1 Next Configuring DS0 Channels DROP/INSERT Interface Network Interface DTE Drop/Insert Interface Drop/Insert Channel Allocation Network E1 Interface Network Channel Allocation Example of Channel Allocation with TS16 Available for Data Example of Interface Worksheet with TS16 Available for Data Port Chan Options Value Conf 10. Port Channel Configuration Worksheet Ports 1 11. Port Channel Configuration Worksheet Ports 3 Symbol Meaning Display Channel SymbolsDisplaying DS0 Channel Assignments Chan Allocating Data PortsPrt1 EditDTE Port Block Channel Assignment Method Individual Channel Assignment Method TS16Rsvd Data Rsvd DTE Channels TS16 Assign Port1 Providing Backup CapabilityClearing DS0 Channel Allocation Clear Channel Selecting the Timing Source 12. Common Clocking Configurations Pri Clk SrcNET Next NET DTE Configuring for Network TimingConfiguring for External Timing Edit NET Chan Gen Clock Rate2048 Next 2048 Acquiring/Releasing User InterfaceAcquiring the Active User Interface Releasing the Active User Interface Download Operations Resetting the E1 DSU/CSUControl ClrReg Reset Device Reset Yes No Changing User Interface Access Security E1 DSU/CSU User Interface Access SecuritySecurity Lvl1 Lvl2 Maintenance Message Description Self-Test HealthSelfTst Health Passed Self-Test Health Messages Device H/S OOF at DTE Device Health and StatusAuto Dev H/S OOF at DTE Health and Status Messages NET Current Event = xx,xxx Network Performance ReportsPerformance NET Prt1 Prt2 NET Registers Cur 24Tot Intvl Clear Prf Regs NET Prt1 Prt2 Clear NETRegs Command CompleteNET Intvl Up Down Dsply NET Intvl nn ES=xxx Event CurTimerVldIntvl Complete StEvnt Alarms Enterprise-Specific Trap Definitions Trap Value Event Snmp TrapsSnmp Trap per Interface Trap Meaning RAI at DTE TroubleshootingTroubleshooting Symptom Possible Cause Solutions RAI at Net # # # # # # # # AIS at DTE Test Jacks Rem Loopback Test CommandsRemote Loopback Tests Test Rlpbk Lpbk Ptrns Valid Loopback Combinations Local Loopback Tests Starting a Payload Loopback Starting a Line LoopbackLoopback Abort LLB PLB Starting a Repeater Loopback Starting a DTE LoopbackLoopback Loopback Dclb Prt1 Prt2 Prt3 Starting a Data Channel Loopback Aborting Loopbacks Starting a Data Terminal LoopbackLoopback Dtlb Prt1 Prt2 Prt3 Patterns Abort Send Mon Test PatternsSending Test Patterns Loopback Abort All 8 Network Qrss Port Patterns Send 511 1in8 QrssTest Started Send Name Prt1 Prt2 Prt3 Monitor Name Prt1 Prt2 Prt3 Monitoring Test Patterns on Individual Data PortsAborting Test Patterns Patterns Mon Qrss Test Lpbk Ptrns Lamp Lamp TestStarting a Lamp Test Patterns Abort All Send Mon Status STest Perf TStat Displaying E1 DSU/CSU Test StatusAborting a Lamp Test 0123456789 = ? Message Description Test Status Messages CID Front Panel Menu a Table B-1 Technical Specifications BModels 3172/3174 DSU/CSUs Technical Specifications Specifications Criteria Port Interface DTE Interface Configuration Options Configuration Options C Table C-1 DTE Interface Configuration Options DTE Interface Configuration Options Table C-2 Port Configuration Options Port Configuration Options InvertTxC Disab Next Enab Disab Prev All Ones Both Next Disab DTR RTS Both PrevRcv RAI Halt Next None Halt Prev Tx Clock Int Next Int Ext Prev Near-end Disab Next Disab Maint Send Both Prev EDL Disab Next Enab Disab Prev Mgmt Link Disab Next Disab Snmp Prev Far-end Disab Next Disab Maint Prev Circuit Ident Next Edit Clear Prev Network Interface Configuration OptionsTable C-3 Network Interface Configuration Options NET Frame noCRC Next CRC4 noCRC Prev Table C-4 DTE Channel Configuration Options Channel Configuration Options Assign By Block Next Block Chan Prev Table C-5 Data Port Channel Configuration OptionsChannel Config Dsply Clear DTE Prt1 Prt2 Prt3 Prt4 Assign To NET Next NET DTE Prtn Prtn Prtn Prev 1472 1536 1600 Port Rate Next 128 192 256 320 384 448 512 576 640 704832 896 960 1024 1088 1216 1280 1344 N10 N11 N12 N31 Next Prev D10 D11 D12 D31 Table C-6 General Configuration Options General Configuration OptionsClock Rate Next 2048 8 Prev Table C-7 User Interface Configuration Options User Interface Configuration Options CStop Bits Next 1 1.5 2 Prev Com Rate Next 1.2 2.4 4.8 9.6 14.4 19.2 38.4 PrevChar Length Next 7 8 Prev CParity None Next None Even Odd Prev Aux Use None Next None Snmp Daisy Prev Ignore DTR No Next Yes No PrevAux Rate Next 9.6 14.4 19.2 38.4 Prev Snmp Trap Disab Next Enab Disab Prev Alarm Configuration OptionsTable C-8 Alarm Configuration Options Alrm Msg Disab Next Enab Disab Prev Table C-9 General Snmp Configuration Options Snmp Configuration Options NetMask Next Edit Clear Prev Access 2 Read Next Read R/W PrevCommunityName2 Next Edit Clear Prev IP Adr Next Edit Clear Prev Com NetMask Next Edit Clear Prev Com IP Adr Next Edit Clear PrevCom Link PPP Next PPP Slip Prev Aux NetMask Next Edit Clear Prev Aux IP Adr Next Edit Clear Prev Gen Trap Both Next Disab Warm Auth Both Prev Table C-10 Snmp Trap Configuration OptionsNum Trap Mgrs Next 1 2 3 4 5 6 Prev Trapn IP Adr Clear Next Edit Clear Prev Link Trap Both Next Disab Up Down Both Prev Entp Trap Enab Next Enab Disab PrevTrap I/F All Next NET DTE E1s Ports All Prev Configuration Worksheets Prt4 Options Value Prt1 Options ValuePrt2 Options Value Prt3 Options Value Network E1 Interface Network Channel Allocation Port Chan Options Value Conf Port Chan Options Value Conf Snmp Trap Value Options General Snmp Value Options Pin Assignments D Table D-1 Signal Pin NumberE1 120 Ohm Balanced Interface Connector E1 Network Interface DTE Drop/Insert Interface DTE Drop/Insert ConnectorTable D-2 AUX Port Interface Table D-3 AUX Port Connector Signal Direction Pin Number COM Port Interface Table D-4 COM Port Connector Signal Direction Pin Number Figure D-3. COM Port-to-PC Cable Direction Pin Mnemonic Number EIA 530A Port Interface Connector Figure D-5. EIA 530A-to-RS449 Cable EIA 530A-to-RS449 Cable Interface Table D-6 RS449 Cable Interface Signal Circuit Figure D-6. EIA 530A-to-V.35 Cable EIA 530A-to-V.35 Cable Interface Direction Pin Number Table D-7 Cable Interface Signal Figure D-7. EIA 530A-to-X.21 Cable EIA 530A-to-X.21 Cable Interface Table D-8 Cable Interface Signal Optional DC Power Cable Power Input ConnectorTable D-9 DC Power Connector Signal Pin Number External Clock Interface Table D-10 External Clock Connector Signal Pin Number Management Information Base MIB II RFC Snmp MIB Objects E Interface Group, MIB System Group, MIB Interface Group ± ªifDescrº Object ifEntry Interface Group ± ªifIndexº Object ifEntryInterface Group ± ªifTypeº Object ifEntry Interface Group ± ªifOperStatusº Object ifEntry Interface Group ± ªifAdminStatusº Object ifEntryInterface Group ± ªifMtuº Object ifEntry Interface Group ± ªifSpeedº Object ifEntry IP Group, MIB IP Group ± ªipRouteMetric2º Object ipRouteEntry IP Group ± ªipRouteTableº Object ipIP Group ± ªipRouteDestº Object ipRouteEntry IP Group ± ªipRouteIfIndexº Object ipRouteEntry Snmp Group, MIB Transmission Group, MIBIcmp Group, MIB UDP Group, MIB Near End Group, DS1/E1 MIB DS1/E1 MIB RFC Near End Group ± ªdsx1SignalModeº Object dsx1ConfigEntry Near End Group ± ªdsx1LineStatusº Object dsx1ConfigEntry Near End Group ± The DS1 Total Table Objects dsx1TotalEntry Near End Group ± ªdsx1Fdlº Object dsx1ConfigEntryFar End Group, DS1/E1 MIB General Port Table, RS-232-like MIB RS-232-like MIB RFCDS1 Fractional Group, DS1/E1 MIB Number of Ports ± ªrs232Numberº Object rs232 Asynchronous Port Table, RS-232-like MIB General Port Table ± ªrs232PortTypeº Object rs232PortEntry Input Signal Table, RS-232-like MIB Output Signal Table, RS-232-like MIBSynchronous Port Table, RS-232-like MIB Generic-Interface Extension MIB RFC Output Signal Table ± ªrs232OutSigChangesº rs232OutSigEntryGeneric Interface Test Table, Generic Interface MIB Paradyne Enterprise MIB Correlation between Menu Commands and Snmp Objects Set dsx1LoopbackConfig for DTE E1 to dsx1LineLoop Set dsx1LoopbackConfig for Net E1 to dsx1LineLoopSet dsx1LoopbackConfig for Net E1 to dsx1NoLoop Set dsx1LoopbackConfig for Net E1 to dsx1PayloadLoop Set/Display dsx1FracNumber and dsx1Fracifindex for DTE or Set/Display dsx1FracNumber and dsx1FracIfindex for DTE E1Display rs232PortInSpeed or rs232PortOutSpeed for port n IP Network Addressing IP Network Addressing Scenario F 135.18.1.2 Front Panel Emulation G Installing Front Panel Emulation Software Starting Front Panel Emulation Equipment List H Equipment Feature Number Activ Glossary CRC4 CRC6 DTR ISO PDU PPP Slip Xtxc Index Index-2 Index-3 Index-4 Index-5