Contents
Main
Agilent Technologies 1664A Logic Analyzer
Page
In This Book
Table of Contents
Page
Page
Page
Page
General Information
Accessories
Specifications
Characteristics
Supplemental Characteristics
Page
Page
Page
Recommended Test Equipment
Equipment Required
18
General Information Recommended Test Equipment
Page
Preparing For Use
Power Requirements
Operating Environment
Storage
Ferrites
To apply power
To operate the user interface
To set the line voltage
To degauss the display
To clean the logic analyzer
To test the logic analyzer
Page
Page
Testing Performance
The Logic Analyzer Interface
Test Strategy
Test Interval
Performance Test Record
To perform the self-tests
Page
Page
To make the test connectors
The test connectors connect the logic analyzer to the test equipment.
Page
To test the threshold accuracy
Page
Test the TTL threshold
Page
Test the ECL threshold
Test the User threshold
Test the + User threshold
Test the 0 V User threshold
Page
To test the glitch capture
Page
Connect the Logic Analyzer to the Pulse Generator
Testing Performance To test the glitch capture
319
Test the glitch capture on the connected channels
Page
Test the next channels
To test the single-clock, single-edge, state acquisition
Page
Page
Page
width is 3.50 ns, +0 ps or 100 ps.
+0 ps or 250 ps.
is 3.50 ns, +0 ps or 100 ps.
Check the setup/hold combination
Page
Page
according to the setup/hold combination selected, +0.0 ps or 100 ps.
Page
To test the multiple-clock, multiple-edge, state acquisition
Page
Page
Page
Page
is 4.450 ns, +50 ps or 100 ps.
Check the setup/hold with single clock edges, multiple clocks
Page
Page
Page
Page
To test the single-clock, multiple-edge, state acquisition
Page
Page
Page
+0 ps or 250 ps.
is 4.000 ns, +0 ps or 100 ps.
Check the setup/hold combination
according to the setup time of the setup/hold combination selected, +0.0 ps or -100.0 ps.
Page
Page
To test the time interval accuracy
Page
Page
Page
Acquire the data
Performance Test Record
359
Performance Test Record (continued)
360
Page
Calibrating and Adjusting
To adjust the CRT monitor alignment
Page
To adjust the CRT intensity
Page
Page
Troubleshooting
To use the flowcharts
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
To check the power-up tests
turning on the power switch.
To run the self-tests
Page
Page
Page
Page
To test the power supply voltages
table.
To test the CRT monitor signals
To test the keyboard signals
To test the disk drive voltages
Page
To perform the BNC test
To test the logic analyzer probe cables
logic analyzer.
Page
Page
To test the auxiliary power
6
Replacing Assemblies
Replacing Assemblies
Replacement Strategy
Tools Required
Exploded View
Listing
63
Replacing Assemblies
Page
To remove and replace the handle
To remove and replace the feet and tilt stand
To remove and replace the cover
To remove and replace the disk drive
To remove and replace the power supply
To remove and replace the Main Circuit board
To remove and replace the switch actuator assembly
the off position.
To remove and replace the rear panel assembly
To remove and replace the front panel and keyboard
To remove and replace the intensity adjustment
To remove and replace the monitor
To remove and replace the handle plate
To remove and replace the fan
To remove and replace the line filter
To remove and replace the optional GPIB and RS-232C cables
To return assemblies
Page
Replaceable Parts
Replaceable Parts Ordering
Page
Replaceable Parts List
75
76
77
Page
Page
Page
Page
Page
Page
Page
Page
Page
Self-Tests Description
Power-up Self-Tests
System Tests (System PV)
Page
Page
Analyzer Tests (Analy PV)
Page
GPIB (Optional)
RS-232C(Optional)
816
RS-232C Signal Definitions
Centronix
817
Centronix Signal Definitions
Page
DECLARATION OF CONFORMITY
