Manuals / Agilent Technologies / Computer Equipment / Switch

Agilent Technologies 01664-97005 manual Select the Front Panel Test

Models: 01664-97005

1 164

Download 164 pages 31.78 Kb

Page 107

Troubleshooting

To run the self-tests

For a Single run, the test runs one time, and the screen shows the results.

13To exit the ROM Test, select Done. Note that the status changes to Passed or Failed.

14Install a formatted disk that is not write protected into the disk drive. If option 020 is installed, connect an RS-232C loopback connector onto the RS-232C port. Run the remaining System Tests in the same manner.

If option 020 is not installed in the 1664A, the RS-232C test will return a FAILED status.

15Select the Front Panel Test.

A screen duplicating the front-panel appears on the screen.

a Press each key on the front panel. The corresponding key on the screen will change from a light to a dark color.

b Test the knob by turning it in both directions.

c Note any failures, then press the Done key a second time to exit the Front Panel Test. The test screen shows the Front Panel Test status changed to Tested.

16Select the Display Test.

A white grid pattern is displayed. These display screens can be used to adjust the display. a Select Continue and the screen changes to full bright.

b Select Continue and the screen changes to half bright.

c Select Continue and the test screen shows the Display Test status changed to Tested.

5–19

Image 107

Agilent Technologies 01664-97005 manual Select the Front Panel Test

Contents

Agilent Technologies 1664A Logic Analyzer Agilent Technologies 1664A Logic Analyzer Agilent Technologies 1664A Logic Analyzer This Book Table of Contents To test the time interval accuracy To adjust the CRT intensityContents Gpib Optional RS-232COptional Centronix Self-Tests DescriptionViii General Information Accessories Available Part Number AccessoriesAccessories Supplied Part Number Qty Accessories AvailableSpecifications Timing Analysis Supplemental CharacteristicsProbes State AnalysisData Entry/Display IndicatorsMeasurement and Display Functions Measurement FunctionsOperating Environment Auxiliary PowerDimensions Marker FunctionsEMC Product RegulationsEquipment Required Recommended Test EquipmentRecommended Test Equipment Preparing for Use Inspect the product for physical damage Check the supplied accessoriesTo inspect the logic analyzer Inspect the shipping container for damageFerrites FerritesTo set the line voltage To apply powerTo apply power To operate the user interfaceTo degauss the display To clean the logic analyzerTo degauss the display To test the logic analyzerPage Testing Performance Testing Performance To perform the self-tests To perform the self-tests Select the Front Panel TestSelect the Display Test Materials Required To make the test connectorsTo make the test connectors To test the threshold accuracy Set up the equipmentTo test the threshold accuracy Set up the logic analyzerConnect the logic analyzer Test the TTL threshold To test the threshold accuracy Test the ECL threshold Test the − User threshold Test the + User threshold Test the 0 V User threshold Test the next pod To test the glitch capture Set up the pulse generatorPulse Generator Setup To test the glitch capture Set up the oscilloscopeOscilloscope Setup Connect the Logic Analyzer to the Pulse Generator Test the glitch capture on the connected channels Set up the Waveform menu to view all the channels Test the next channels To test the single-clock, single-edge, state acquisition To test the single-clock, single-edge, state acquisition Set up the Trigger menu Set up the Format menuConnect the 1664A Logic Analyzer to the Pulse Generator Verify the test signal To test the single-clock, single-edge, state acquisition Setup/Hold Combinations Check the setup/hold combinationSelect the logic analyzer setup/hold time Clocks Select the clock to be testedTo test the single-clock, single-edge, state acquisition Select the clock to be tested Test the next setup/hold combination To test the multiple-clock, multiple-edge, state acquisition To test the multiple-clock, multiple-edge, state acquisition Set up the Format menu Pod 1, channel Verify the test signal To test the multiple-clock, multiple-edge, state acquisition 0.0 ns 4.5 ns 2.5 ns Select the clocks to be tested To test the multiple-clock, multiple-edge, state acquisition Select the clocks to be tested Hen continue through the complete test To test the single-clock, multiple-edge, state acquisition Set up the pulse generator according to the following tableTo test the single-clock, multiple-edge, state acquisition Set up the Format menu Channel Verify the test signal To test the single-clock, multiple-edge, state acquisition Logic analyzer Format menu, select Master Clock These proceduresOscilloscope Timebase Delay Test the next clock EXT Trig To test the time interval accuracyTo test the time interval accuracy Function Generator SetupSet up the Format menu Set up the Waveform menu. a Press the Waveform key Acquire the data Performance Test Record 1664A Logic Analyzer Performance Test RecordPerformance Test Record Calibrating and Adjusting Logic analyzer calibration Calibrating and AdjustingCause personal injury To adjust the CRT monitor alignmentEnter the Sys PV tests, then enter the Display Test To adjust the CRT monitor alignmentPress the front panel Select key To adjust the CRT intensityTo adjust the CRT intensity Troubleshooting To use the flowcharts TroubleshootingTo use the flowcharts TroubleshootingTroubleshooting Troubleshooting Troubleshooting To use the flowcharts To use the flowcharts Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting As the tests complete, check if they pass or fail To check the power-up testsTo check the power-up tests To run the self-tests To run the self-testsSelect the Chip 5 Tests menu and press the Select key To run the self-tests To run the self-tests Select the Front Panel Test To run the self-tests Loaded by the acquisition board To test the power supply voltagesTo test the power supply voltages Load the +5.00 V supply with a 2 Ω, 25 watt resistorSignals on the Power Supply Cable CRT Monitor Cable Signals To test the CRT monitor signalsTo test the CRT monitor signals Keyboard Connector Signals To test the keyboard signalsTurn off the instrument and remove the power cable To test the keyboard signalsTo test the disk drive voltages To test the disk drive voltagesDisk Drive Voltages Pin Signal DescriptionTo perform the BNC test Press the Config key Assign pods 1 and 2 to MachineTo perform the BNC test To test the logic analyzer probe cables Set up the logic analyzer Configuration menuTo test the logic analyzer probe cables Set up the Format menu. a Press the Format key Select Clear Trigger, then select All Return to the troubleshooting flowchart To test the auxiliary power To test the auxiliary powerReplacing Assemblies Replacing Assemblies Listing Exploded ViewReplacing Assemblies To remove and replace the cover Reverse this procedure to install the coverTo remove and replace the handle To remove and replace the feet and tilt standTo remove and replace the disk drive Using previous procedures, remove the following assembliesReverse this procedure to install the disk drive To remove and replace the disk driveTo remove and replace the Main Circuit board To remove and replace the power supplyTo remove and replace the power supply To remove and replace the switch actuator assembly To remove and replace the switch actuator assemblyVerify the push-on, push-off action of the assembly To remove and replace the rear panel assembly To remove and replace the rear panel assemblyTo remove and replace the front panel and keyboard To remove and replace the intensity adjustmentTo remove and replace the front panel and keyboard To remove and replace the monitor Reverse this procedure to install the handle plateTo remove and replace the monitor To remove and replace the handle plateTo remove and replace the fan To remove and replace the fanTo remove and replace the line filter To remove and replace the optional Gpib and RS-232C cables Seal the shipping container securely, and mark it Fragile Remove accessories from the logic analyzerTo return assemblies Package the logic analyzerReplaceable Parts Direct mail order system Parts listedReplaceable Parts Ordering Parts not listedExploded View Exploded ViewReplaceable Parts List Replaceable Parts ListAgilent Des Part Qty Description Number Replaceable Parts List 1664A Replaceable PartsMP1 RS-232 loopback connector Power Cables and Plug Configurations Power Cables and Plug ConfigurationsTheory of Operation Theory of Operation 1664A Logic Analyzer Block-Level TheoryDisk Drive Controller 1664A TheorySystem Memory CRT Controller and Display RAMCentronix Interface CRT Monitor AssemblyPower Supply External Keyboard InterfaceLogic Acquisition Circuitry Theory of OperationAcquisition Main Circuit Board Logic Acquisition Theory ProbingComparators Test and Clock Synchronization Circuit ThresholdROM Test Power-up Self-TestsSelf-Tests Description Interrupt Test System Tests System PVSystem Tests System PV RAM TestDisk Test Gpib TestRS-232C Test HIL TestDisplay Test Perform Test AllFront Panel Test Chip Tests Analyzer Tests Analy PVAnalyzer Tests Analy PV Board TestData Input Inspection Gpib Optional RS-232COptional RS-232C Signal DefinitionsCentronix Centronix Signal DefinitionsPage Declaration of Conformity Page Document Warranty Product Warranty