Manuals / Agilent Technologies / Computer Equipment / Switch

Agilent Technologies 01664-97005 manual To run the self-tests

Models: 01664-97005

1 164

Download 164 pages 31.78 Kb

Page 105

Troubleshooting

To run the self-tests

6Select Run, then select Single. The test runs one time, then the screen shows the results. When the test is finished, select Done.

To run a test continuously, select Repetitive. Select Stop to halt a Run Repetitive.

7Select Board Tests, then select Run. When the Board Tests are finished, select Done.

8Select Data Input Inspection. All lines should show activity. Select Done to exit the Data Input Inspection.

9Select Analy PV, then select Sys PV PV in the pop up menu and press the Select key.

5–17

Image 105

Agilent Technologies 01664-97005 manual To run the self-tests

Contents

Agilent Technologies 1664A Logic Analyzer Agilent Technologies 1664A Logic Analyzer Agilent Technologies 1664A Logic Analyzer This Book Table of Contents To adjust the CRT intensity ContentsTo test the time interval accuracy Gpib Optional RS-232COptional Centronix Self-Tests DescriptionViii General Information Accessories Supplied Part Number Qty AccessoriesAccessories Available Accessories Available Part NumberSpecifications Probes Supplemental CharacteristicsState Analysis Timing AnalysisMeasurement and Display Functions IndicatorsMeasurement Functions Data Entry/DisplayDimensions Auxiliary PowerMarker Functions Operating EnvironmentEMC Product RegulationsRecommended Test Equipment Recommended Test EquipmentEquipment Required Preparing for Use To inspect the logic analyzer Check the supplied accessoriesInspect the shipping container for damage Inspect the product for physical damageFerrites FerritesTo apply power To apply powerTo operate the user interface To set the line voltageTo degauss the display To clean the logic analyzerTo test the logic analyzer To degauss the displayPage Testing Performance Testing Performance To perform the self-tests To perform the self-tests Select the Front Panel TestSelect the Display Test Materials Required To make the test connectorsTo make the test connectors To test the threshold accuracy Set up the equipmentSet up the logic analyzer Connect the logic analyzerTo test the threshold accuracy Test the TTL threshold To test the threshold accuracy Test the ECL threshold Test the − User threshold Test the + User threshold Test the 0 V User threshold Test the next pod Set up the pulse generator Pulse Generator SetupTo test the glitch capture Set up the oscilloscope Oscilloscope SetupTo test the glitch capture Connect the Logic Analyzer to the Pulse Generator Test the glitch capture on the connected channels Set up the Waveform menu to view all the channels Test the next channels To test the single-clock, single-edge, state acquisition To test the single-clock, single-edge, state acquisition Set up the Trigger menu Set up the Format menuConnect the 1664A Logic Analyzer to the Pulse Generator Verify the test signal To test the single-clock, single-edge, state acquisition Check the setup/hold combination Select the logic analyzer setup/hold timeSetup/Hold Combinations Clocks Select the clock to be testedTo test the single-clock, single-edge, state acquisition Select the clock to be tested Test the next setup/hold combination To test the multiple-clock, multiple-edge, state acquisition To test the multiple-clock, multiple-edge, state acquisition Set up the Format menu Pod 1, channel Verify the test signal To test the multiple-clock, multiple-edge, state acquisition 0.0 ns 4.5 ns 2.5 ns Select the clocks to be tested To test the multiple-clock, multiple-edge, state acquisition Select the clocks to be tested Hen continue through the complete test To test the single-clock, multiple-edge, state acquisition Set up the pulse generator according to the following tableTo test the single-clock, multiple-edge, state acquisition Set up the Format menu Channel Verify the test signal To test the single-clock, multiple-edge, state acquisition Logic analyzer Format menu, select Master Clock These proceduresOscilloscope Timebase Delay Test the next clock EXT Trig To test the time interval accuracyTo test the time interval accuracy Function Generator SetupSet up the Format menu Set up the Waveform menu. a Press the Waveform key Acquire the data Performance Test Record 1664A Logic Analyzer Performance Test RecordPerformance Test Record Calibrating and Adjusting Logic analyzer calibration Calibrating and AdjustingCause personal injury To adjust the CRT monitor alignmentEnter the Sys PV tests, then enter the Display Test To adjust the CRT monitor alignmentPress the front panel Select key To adjust the CRT intensityTo adjust the CRT intensity Troubleshooting To use the flowcharts TroubleshootingTo use the flowcharts TroubleshootingTroubleshooting Troubleshooting Troubleshooting To use the flowcharts To use the flowcharts Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting To check the power-up tests To check the power-up testsAs the tests complete, check if they pass or fail To run the self-tests Select the Chip 5 Tests menu and press the Select keyTo run the self-tests To run the self-tests To run the self-tests Select the Front Panel Test To run the self-tests To test the power supply voltages To test the power supply voltagesLoad the +5.00 V supply with a 2 Ω, 25 watt resistor Loaded by the acquisition boardSignals on the Power Supply Cable To test the CRT monitor signals To test the CRT monitor signalsCRT Monitor Cable Signals Turn off the instrument and remove the power cable To test the keyboard signalsTo test the keyboard signals Keyboard Connector SignalsTo test the disk drive voltages To test the disk drive voltagesDisk Drive Voltages Pin Signal DescriptionPress the Config key Assign pods 1 and 2 to Machine To perform the BNC testTo perform the BNC test Set up the logic analyzer Configuration menu To test the logic analyzer probe cablesTo test the logic analyzer probe cables Set up the Format menu. a Press the Format key Select Clear Trigger, then select All Return to the troubleshooting flowchart To test the auxiliary power To test the auxiliary powerReplacing Assemblies Replacing Assemblies Listing Exploded ViewReplacing Assemblies To remove and replace the handle Reverse this procedure to install the coverTo remove and replace the feet and tilt stand To remove and replace the coverReverse this procedure to install the disk drive Using previous procedures, remove the following assembliesTo remove and replace the disk drive To remove and replace the disk driveTo remove and replace the power supply To remove and replace the power supplyTo remove and replace the Main Circuit board To remove and replace the switch actuator assembly Verify the push-on, push-off action of the assemblyTo remove and replace the switch actuator assembly To remove and replace the rear panel assembly To remove and replace the rear panel assemblyTo remove and replace the intensity adjustment To remove and replace the front panel and keyboardTo remove and replace the front panel and keyboard To remove and replace the monitor Reverse this procedure to install the handle plateTo remove and replace the handle plate To remove and replace the monitorTo remove and replace the fan To remove and replace the line filterTo remove and replace the fan To remove and replace the optional Gpib and RS-232C cables To return assemblies Remove accessories from the logic analyzerPackage the logic analyzer Seal the shipping container securely, and mark it FragileReplaceable Parts Replaceable Parts Ordering Parts listedParts not listed Direct mail order systemExploded View Exploded ViewReplaceable Parts List Replaceable Parts ListAgilent Des Part Qty Description Number Replaceable Parts List 1664A Replaceable PartsMP1 RS-232 loopback connector Power Cables and Plug Configurations Power Cables and Plug ConfigurationsTheory of Operation Theory of Operation 1664A Logic Analyzer Block-Level TheorySystem Memory 1664A TheoryCRT Controller and Display RAM Disk Drive ControllerPower Supply CRT Monitor AssemblyExternal Keyboard Interface Centronix InterfaceLogic Acquisition Circuitry Theory of OperationMain Circuit Board Logic Acquisition Theory Probing ComparatorsAcquisition Test and Clock Synchronization Circuit ThresholdPower-up Self-Tests Self-Tests DescriptionROM Test System Tests System PV System Tests System PVRAM Test Interrupt TestRS-232C Test Gpib TestHIL Test Disk TestPerform Test All Front Panel TestDisplay Test Analyzer Tests Analy PV Analyzer Tests Analy PVBoard Test Chip TestsData Input Inspection Gpib Optional RS-232COptional RS-232C Signal DefinitionsCentronix Centronix Signal DefinitionsPage Declaration of Conformity Page Document Warranty Product Warranty