Test the TTL threshold | Agilent Technologies 01664-97005 specification

Testing Performance

To test the threshold accuracy

Test the TTL threshold

1Press the Format key. Select the field to the right of Pod 1, then select TTL in the pop-up menu.

2On the function generator front panel, enter 1.647 V ±1 mV DC offset. Use the multimeter to verify the voltage.

The activity indicators for pod 1 should show all data channels and the J-clock channel at a logic high.

3Using the Modify down arrow on the function generator, decrease offset voltage in 1-mV increments until all activity indicators for pod 1 show the channels at a logic low. Record the function generator voltage in the performance test record.

3–10

Image 32

Agilent Technologies 01664-97005 manual Test the TTL threshold

Contents

Agilent Technologies 1664A Logic Analyzer Agilent Technologies 1664A Logic Analyzer Agilent Technologies 1664A Logic Analyzer This Book Table of Contents To test the time interval accuracy To adjust the CRT intensityContents Self-Tests Description Gpib Optional RS-232COptional Centronix Viii General Information Accessories Accessories Supplied Part Number QtyAccessories Available Accessories Available Part Number Specifications Supplemental Characteristics ProbesState Analysis Timing Analysis Indicators Measurement and Display FunctionsMeasurement Functions Data Entry/Display Auxiliary Power DimensionsMarker Functions Operating Environment Product Regulations EMC Equipment Required Recommended Test EquipmentRecommended Test Equipment Preparing for Use Check the supplied accessories To inspect the logic analyzerInspect the shipping container for damage Inspect the product for physical damage Ferrites Ferrites To apply power To apply powerTo operate the user interface To set the line voltage To clean the logic analyzer To degauss the displayTo test the logic analyzer To degauss the displayPage Testing Performance Testing Performance To perform the self-tests Select the Front Panel Test To perform the self-tests Select the Display Test To make the test connectors Materials Required To make the test connectors Set up the equipment To test the threshold accuracy To test the threshold accuracy Set up the logic analyzerConnect the logic analyzer Test the TTL threshold To test the threshold accuracy Test the ECL threshold Test the − User threshold Test the + User threshold Test the 0 V User threshold Test the next pod To test the glitch capture Set up the pulse generatorPulse Generator Setup To test the glitch capture Set up the oscilloscopeOscilloscope Setup Connect the Logic Analyzer to the Pulse Generator Test the glitch capture on the connected channels Set up the Waveform menu to view all the channels Test the next channels To test the single-clock, single-edge, state acquisition To test the single-clock, single-edge, state acquisition Set up the Format menu Set up the Trigger menu Connect the 1664A Logic Analyzer to the Pulse Generator Verify the test signal To test the single-clock, single-edge, state acquisition Setup/Hold Combinations Check the setup/hold combinationSelect the logic analyzer setup/hold time Select the clock to be tested Clocks To test the single-clock, single-edge, state acquisition Select the clock to be tested Test the next setup/hold combination To test the multiple-clock, multiple-edge, state acquisition To test the multiple-clock, multiple-edge, state acquisition Set up the Format menu Pod 1, channel Verify the test signal To test the multiple-clock, multiple-edge, state acquisition 0.0 ns 4.5 ns 2.5 ns Select the clocks to be tested To test the multiple-clock, multiple-edge, state acquisition Select the clocks to be tested Hen continue through the complete test Set up the pulse generator according to the following table To test the single-clock, multiple-edge, state acquisition To test the single-clock, multiple-edge, state acquisition Set up the Format menu Channel Verify the test signal To test the single-clock, multiple-edge, state acquisition These procedures Logic analyzer Format menu, select Master Clock Oscilloscope Timebase Delay Test the next clock To test the time interval accuracy EXT Trig Function Generator Setup To test the time interval accuracy Set up the Format menu Set up the Waveform menu. a Press the Waveform key Acquire the data Performance Test Record Performance Test Record 1664A Logic Analyzer Performance Test Record Calibrating and Adjusting Calibrating and Adjusting Logic analyzer calibration To adjust the CRT monitor alignment Cause personal injury To adjust the CRT monitor alignment Enter the Sys PV tests, then enter the Display Test To adjust the CRT intensity Press the front panel Select key To adjust the CRT intensity Troubleshooting Troubleshooting To use the flowcharts Troubleshooting To use the flowcharts Troubleshooting Troubleshooting Troubleshooting To use the flowcharts To use the flowcharts Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting As the tests complete, check if they pass or fail To check the power-up testsTo check the power-up tests To run the self-tests To run the self-testsSelect the Chip 5 Tests menu and press the Select key To run the self-tests To run the self-tests Select the Front Panel Test To run the self-tests To test the power supply voltages To test the power supply voltagesLoad the +5.00 V supply with a 2 Ω, 25 watt resistor Loaded by the acquisition board Signals on the Power Supply Cable CRT Monitor Cable Signals To test the CRT monitor signalsTo test the CRT monitor signals To test the keyboard signals Turn off the instrument and remove the power cableTo test the keyboard signals Keyboard Connector Signals To test the disk drive voltages To test the disk drive voltages Pin Signal Description Disk Drive Voltages To perform the BNC test Press the Config key Assign pods 1 and 2 to MachineTo perform the BNC test To test the logic analyzer probe cables Set up the logic analyzer Configuration menuTo test the logic analyzer probe cables Set up the Format menu. a Press the Format key Select Clear Trigger, then select All Return to the troubleshooting flowchart To test the auxiliary power To test the auxiliary power Replacing Assemblies Replacing Assemblies Exploded View Listing Replacing Assemblies Reverse this procedure to install the cover To remove and replace the handleTo remove and replace the feet and tilt stand To remove and replace the cover Using previous procedures, remove the following assemblies Reverse this procedure to install the disk driveTo remove and replace the disk drive To remove and replace the disk drive To remove and replace the Main Circuit board To remove and replace the power supplyTo remove and replace the power supply To remove and replace the switch actuator assembly To remove and replace the switch actuator assemblyVerify the push-on, push-off action of the assembly To remove and replace the rear panel assembly To remove and replace the rear panel assembly To remove and replace the front panel and keyboard To remove and replace the intensity adjustmentTo remove and replace the front panel and keyboard Reverse this procedure to install the handle plate To remove and replace the monitorTo remove and replace the handle plate To remove and replace the monitor To remove and replace the fan To remove and replace the fanTo remove and replace the line filter To remove and replace the optional Gpib and RS-232C cables Remove accessories from the logic analyzer To return assembliesPackage the logic analyzer Seal the shipping container securely, and mark it Fragile Replaceable Parts Parts listed Replaceable Parts OrderingParts not listed Direct mail order system Exploded View Exploded View Replaceable Parts List Replaceable Parts List Replaceable Parts List 1664A Replaceable Parts Agilent Des Part Qty Description Number MP1 RS-232 loopback connector Power Cables and Plug Configurations Power Cables and Plug Configurations Theory of Operation Theory of Operation Block-Level Theory 1664A Logic Analyzer 1664A Theory System MemoryCRT Controller and Display RAM Disk Drive Controller CRT Monitor Assembly Power SupplyExternal Keyboard Interface Centronix Interface Theory of Operation Logic Acquisition Circuitry Acquisition Main Circuit Board Logic Acquisition Theory ProbingComparators Threshold Test and Clock Synchronization Circuit ROM Test Power-up Self-TestsSelf-Tests Description System Tests System PV System Tests System PVRAM Test Interrupt Test Gpib Test RS-232C TestHIL Test Disk Test Display Test Perform Test AllFront Panel Test Analyzer Tests Analy PV Analyzer Tests Analy PVBoard Test Chip Tests Data Input Inspection Gpib Optional RS-232C Signal Definitions RS-232COptional Centronix Signal Definitions CentronixPage Declaration of Conformity Page Document Warranty Product Warranty