AMD SC3200 Reserved Inten Interrupt Enable, Stop Stop, Saen Slave Address Enable, EN Enable, 126

32581C SuperI/O Module

Table 5-32. ACB Registers (Continued)

Bit Description

4ACK (Acknowledge). This bit is ignored in transmit mode. When the device acts as a receiver (slave or master), this bit holds the stop transmitting instruction that is transmitted during the next acknowledge cycle.

0:Cleared after acknowledge cycle.

1:Negative acknowledge issued on next received byte.

3Reserved.

2INTEN (Interrupt Enable).

0:ACB interrupt disabled.

1:ACB interrupt enabled. An interrupt is generated in response to one of the following events: -Detection of an address match (ACBST[2] = 1) and ACBCTL1[6] = 1.

-Receipt of Bus Error (ACBST[5] = 1).

-Receipt of Negative Acknowledge after sending a byte (ACBST[4] = 1).

-Acknowledge of each transaction (same as the hardware set of the ACBST[6]). -In master mode if ACBCTL1[7] = 1, after a successful start (ACBST[3] = 1). -Detection of a Stop Condition while in slave mode (ACBST[7] = 1).

1STOP (Stop).

0:Automatically cleared after Stop issued.

1:Setting this bit in master mode generates a Stop Condition to complete or abort current message transfer.

0START (Start). Set this bit only when in master mode or when requesting master mode.

0:Cleared after Start Condition sent or Bus Error (ACBST[5] = 1) detected.

1:Single or repeated Start Condition generated on the ACCESS.bus. If the device is not the active master of the bus (ACBST[1] = 0), setting START generates a Start Condition when the ACCESS.bus becomes free (ACBCST[1] = 0). An address transmission sequence should then be performed.

If the device is the active master of the bus (ACBST[1] = 1), setting START and then writing to ACBSDA generates a Start Condition. If a transmission is already in progress, a repeated Start Condition is generated. This condition can be used to switch the direction of the data flow between the master and the slave, or to choose another slave device without separating them with a Stop Condition.

Offset 04h ACB Own Address Register - ACBADDR (R/W) Reset Value: xxh

7SAEN (Slave Address Enable).

0:ACB does not check for an address match with ACBADDR[6:0].

1:ACBADDR[6:0] holds a valid address and enables the match of ADDR to an incoming address byte.

6:0		ADDR (Address). These bits hold the 7-bit device address of the SC3200. When in slave mode, the first 7 bits received
		after a Start Condition are compared with this field (first bit received is compared with bit 6, and the last bit with bit 0). If the
		address field matches the received data and ACBADDR[7] is 1, a match is declared.
Offset	05h	ACB Control Register 2 - ACBCTL2 (R/W)	Reset Value: 00h

This register enables/disables the functional block and determines the ACB clock rate.

7:1	ABCFRQ (ABC Frequency). This field defines the ABC period (low and high time) when the device serves as a bus mas-
	ter. The clock low and high times are defined as follows:
	tABCl = tABCh = 2*ABCFRQ*tCLK
	where tCLK is the module input clock cycle, as defined in the Section 5.2 "Module Architecture" on page 89.
	ABCFRQ can be programmed to values in the range of 0001000b through 1111111b. Using any other value has unpredict-
	able results.

0EN (Enable).

0:ACB is disabled, ACBCTL1, ACBST and ACBCST registers are cleared, and clocks are halted.

1:ACB is enabled.

126 AMD Geode™ SC3200 Processor Data Book