AMD SC3200 manual Index 04h Hours Register HOR R/W, Index 05h Hours Alarm Register Hora R/W, 110

	32581C	SuperI/O Module
	Table 5-20. RTC Registers (Continued)
Bit	Description
Index 03h	Minutes Alarm Register - MINA (R/W)	Reset Type: VPP PUR
7:0	Minutes Alarm Data. Values can be 00 to 59 in BCD format, or 00 to 3B in binary format.

When bits 7 and 6 are both set to 1, unconditional match is selected. See Section 5.5.2.5 "Alarms" on page 105 for more information about “unconditional” matches.

Index 04h Hours Register - HOR (R/W) Reset Type: VPP PUR

7:0

Hours Data. For 12-hour mode, values can be 01 to 12 (AM) and 81 to 92 (PM) in BCD format, or 01 to 0C (AM) and 81 to 8C (PM) in binary format. For 24-hour mode, values can be 0- to 23 in BCD format or 00 to 17 in binary format.

Index 05h Hours Alarm Register - HORA (R/W) Reset Type: VPP PUR

7:0

Hours Alarm Data. For 12-hour mode, values may be 01 to 12 (AM) and 81 to 92 (PM) in BCD format or 01 to 0C (AM) and 81 to 8C (PM) in Binary format. For 24-hour mode, values may be 0- to 23 in BCD format or 00 to 17 in Binary format.

When bits 7 and 6 are both set to one (“11”), unconditional match is selected.

Index 06h	Day of Week Register - DOW (R/W)	Reset Type: VPP PUR
7:0	Day Of Week Data. Values may be 01 to 07 in BCD format or 01 to 07 in binary format.
Index 07h	Date of Month Register - DOM (R/W)	Reset Type: VPP PUR
7:0	Date Of Month Data. Values may be 01 to 31 in BCD format or 01 to 1F in binary format.
Index 08h	Month Register - MON (R/W)	Reset Type: VPP PUR
Width: Byte
7-0	Month Data. Values may be 01 to 12 in BCD format or 01 to 0C in binary format.
Index 09h	Year Register - YER (R/W)	Reset Type: VPP PUR
7:0	Year Data. Values may be 00 to 99 in BCD format or 00 to 63 in binary format.
Index 0Ah	RTC Control Register A - CRA (R/W)	Reset Type: Bit Specific

This register controls test selection, among other functions. This register cannot be written before reading bit 7 of CRD.

7Update in Progress. (RO) This bit is not affected by reset. This bit reads 0 when bit 7 of the CRB Register is 1.

0:Timing registers not updated within 244 μs.

1:Timing registers updated within 244 μs.

6:4	Divider Chain Control. These bits control the configuration of the divider chain for timing generation and register bank
	selection. See Table 5-21 on page 112. They are cleared to 000 as long as bit 7 of CRD is 0.
3:0	Periodic Interrupt Rate Select. These bits select one of fifteen output taps from the clock divider chain to control the rate of
	the periodic interrupt. See Table 5-22 on page 112 and Figure 5-7 on page 104. They are cleared to 000 as long as bit 7 of
	CRD is 0.
Index 0Bh	RTC Control Register B - CRB (R/W)	Reset Type: Bit Specific

7Set Mode. This bit is reset at VPP power-up reset only.

0:Timing updates occur normally.

1:User copy of time is “frozen”, allowing the time registers to be accessed whether or not an update occurs.

6Periodic Interrupt. Bits [3:0] of the CRA Register determine the rate at which this interrupt is generated. It is cleared to 0 on RTC reset (i.e., hardware or software reset) or when RTC is disable.

0:Disable.

1:Enable.

5Alarm Interrupt. This interrupt is generated immediately after a time update in which the seconds, minutes, hours, date and month time equal their respective alarm counterparts. It is cleared to 0 as long as bit 7 of the CRD Register is reads 0.

0:Disable.

1:Enable.

4Update Ended Interrupt. This interrupt is generated when an update occurs. It is cleared to 0 on RTC reset (i.e., hardware or software reset) or when the RTC is disable.

0:Disable.

1:Enable.

110 AMD Geode™ SC3200 Processor Data Book