AMD SC3200 manual Strap Options, Nominal External PU/PD Strap Settings

32581C Signal Definitions

3.2Strap Options

Several balls are read at power-up that set up the state of the SC3200. These balls are typically multiplexed with other functions that are outputs after the power-up sequence is complete. The SC3200 must read the state of the balls at power-up and the internal PU or PD resistors do not guarantee the correct state will be read. Therefore, it is required that an external PU or PD resistor with a value

of 1.5 KΩ be placed on the balls listed in Table 3-4.The value of the resistor is important to ensure that the proper state is read during the power-up sequence. If the ball is not read correctly at power-up, the SC3200 may default to a state that causes it to function improperly, possibly result- ing in application failure.

Table 3-4. Strap Options

			Nominal	External PU/PD Strap Settings
Strap			Internal
Option	Muxed With	Ball No.	PU or PD	Strap = 0 (PD)	Strap = 1 (PU)	Register References
CLKSEL0	RD#	B8	PD100	See Table 4-7 on page 83 for		GCB+I/O Offset 1Eh[9:8] (aka CCFC regis-
				CLKSEL strap options.		ter bits [9:8]) (RO): Value programmed at
CLKSEL1	SOUT1	AF3	PD100
						reset by
CLKSEL2	SOUT2	D29	PD100			CLKSEL[1:0].
CLKSEL3	SYNC	P30	PD100			GCB+I/O Offset 10h[3:0] (aka MCCM regis-
						ter bits [3:0]) (RO): Value programmed at
						reset by
						CLKSEL[3:0].
						GCB+I/O Offset 1Eh[3:0] (aka CCFC regis-
						ter bits [3:0]) (R/W, but write not recom-
						mended): Value programmed at reset by
						CLKSEL[3:0].
						Note: Values for GCB+I/O Offset 10h[3:0]
						and 1Eh[3:0] are not the same.
BOOT16	ROMCS#	C8	PD100	Enable boot	Enable boot	GCB+I/O Offset 34h[3] (aka MCR register
				from 8-bit ROM	from 16-bit	bit 3) (RO): Reads back strap setting.
					ROM	GCB+I/O Offset 34h[14] (R/W): Used to
						allow the ROMCS# width to be changed
						under program control.
TFT_PRSNT	SDATA_OUT	P29	PD100	TFT not muxed	TFT muxed	GCB+I/O Offset 30h[23] (aka PMR register
				onto Parallel	onto Parallel	bit 23) (R/W): Reads back strap setting.
				Port	Port
LPC_ROM	PCICLK1	D6	PD100	Disable boot	Enable boot	F0BAR1+I/O Offset 10h[15] (R/W): Reads
				from ROM on	from ROM on	back strap setting and allows LPC ROM to
				LPC bus	LPC bus	be changed under program control.
FPCI_MON	PCICLK0	A4	PD100	Disable Fast-	Enable Fast-	GCB+I/O Offset 34h[30] (aka MCR register
				PCI, INTR_O,	PCI, INTR_O,	bit 30) (RO): Reads back strap setting.
				and SMI_O	and SMI_O	Note:	For normal operation, strap this
				monitoring sig-	monitoring sig-
							signal low using a 1.5 KΩ resistor.
				nals.	nals. (Useful
					during debug.)
DID0	GNT0#	C5	PD100	Defines the system-level chip ID.		GCB+I/O Offset 34h[31,29] (aka MCR regis-
						ter bits 31 and 29) (RO): Reads back strap
DID1	GNT1#	C6	PD100
						setting.
						Note:	GNT0# must have a PU resistor of
							1.5 KΩ and GNT1# must have a
							PU resistor of 1.5 KΩ.
Note: Accuracy of internal PU/PD resistors: 80K to 250K.
Location of the GCB (General Configuration Block) cannot be determined by software. See the AMD Geode™ SC3200 Specifi-
cation Update document.

44 AMD Geode™ SC3200 Processor Data Book