Electrical Data | Carrier 69NT40-511-199, 69NT40-521 manual

2.3 ELECTRICAL DATA

		CB-1 Trips at	29 amps
	a. Circuit Breaker	CB-2 (50 amp) Trips at	62.5 amps
		CB-2 (70 amp) Trips at	87.5 amps
	b. Compressor	Full Load Amps (FLA)	17.6 amps @ 460 vac
	Motor	Full Load Amps (FLA)	(with current limiting set at 21 amps)
	Motor		(with current limiting set at 21 amps)
			380 vac, 3 Phase, 50 hz		460 vac, 3 Phase, 60 hz

		Full Load Amps	1.3 amps		1.6 amps

	c. Condenser Fan	Horsepower	0.43 hp		0.75 hp

		Rotations Per Minute	1425 rpm		1725 rpm
	Motor	Rotations Per Minute	1425 rpm		1725 rpm

		Voltage and Frequency	360 -- 460 vac ¦ 1.25 hz		400 -- 500 vac ¦ 1.5 hz
		Voltage and Frequency	360 -- 460 vac ¦ 1.25 hz		400 -- 500 vac ¦ 1.5 hz

		Bearing Lubrication	Factory lubricated, additional grease not required.

		Rotation	Counter-clockwise when viewed from shaft end.
		Number of Heaters		1

	d. Drain Pan Heaters	Rating	750 watts +5 /--10 % @ 460 vac

		Resistance (cold)	285 ¦ 7.5% ohms nominal

		Type	Sheath

		Number of Heaters		4

	e. Evaporator Coil	Rating	750 watts +5/--10% each @ 230 vac

		Resistance (cold)	66.8 to 77.2 ohms
	Heaters	Resistance (cold)	66.8 to 77.2 ohms

		Ambient	@ 20 _C (68 _F)
		Ambient	@ 20 _C (68 _F)

		Type	Sheath

			380 vac, 3 Phase, 50 hz		460 vac, 3 Phase, 60 hz

		Full Load Amps -- High	1.6 amps		2.0 amps
		Speed	1.6 amps		2.0 amps
		Speed
		Full Load Amps -- Low	0.8 amps		1.0 amps
		Speed	0.8 amps		1.0 amps
		Speed
		Nominal Horsepower --	0.70 hp		0.84 hp
		High Speed	0.70 hp		0.84 hp
		High Speed
		Nominal Horsepower --	0.09 hp		0.11 hp
	f. Evaporator Fan	Low Speed	0.09 hp		0.11 hp
	f. Evaporator Fan	Low Speed
	Motor(s)	Rotations Per Minute --	2850 rpm		3450 rpm
		High Speed	2850 rpm		3450 rpm
		High Speed
		Rotations Per Minute --	1425 rpm		1750 rpm
		Low Speed	1425 rpm		1750 rpm
		Low Speed
		Voltage and Frequency	360 -- 460 vac ¦ 1.25 hz		400 -- 500 vac ¦ 1.5 hz
		Voltage and Frequency --	180 -- 230 vac ¦ 1.25 hz		200 -- 250 vac ¦ 1.5 hz
		using modular transformer	180 -- 230 vac ¦ 1.25 hz		200 -- 250 vac ¦ 1.5 hz
		using modular transformer
		Bearing Lubrication	Factory lubricated, additional grease not required

		Rotation	Clockwise when viewed from shaft end.

	g. Fuses	Control Circuit	15 amps (F3)

		Controller/DataCORDER	5 amps (F1 & F2)
		Controller/DataCORDER	5 amps (F1 & F2)
	h. Compressor Crankcase Heater (CCH) --		180 watts @ 460 vac
	Optional		180 watts @ 460 vac
	Optional

SECTION 2

2-11

T-268-07

Image 30

Carrier 69NT40-511-199, 69NT40-521 manual Electrical Data

Contents

Container Refrigeration Unit Operation Container Refrigeration Unit Models Maintenance Precautions General Safety NoticesOperating Precautions Safety-1 268-07 Safety-2 Specific Warning and Caution Statements Table of Contents Operation Section Service Iii 268-07 List of Illustrations 27 Suction Solenoid Valve SSV -- Alco List of Tables Section Introduction Introduction Model Chart Model Transformer Humidity Sensor TransFresh PID 69NT40-511-58 69NT40-511-71 69NT40-511-95 69NT40-521-10 General Description Refrigeration Unit -- Front Section Evaporator Section Refrigeration Unit -- Rear Panels Removed Compressor Section 1011 Condenser Section Condenser Section 268-07 Receiver Section 1716 Water-Cooled Condenser Section Optional Units with Water-Cooled Condenser Control Box with a Single-Speed Compressor 1236 9 Control Box with a Two-Speed Compressor Optional Refrigeration System Data Electrical Data To Operate Unit on 380/460 vac Power Supply Power Autotransformer OptionalStep-Up Power Autotransformer To Operate Unit on 190/230 vac Power Supply Lower Fresh AIR Makeup Vent Optional Upper Fresh AIR Makeup VentFull Open or Closed Positions Air Sampling for Carbon Dioxide CO2 Level Refrigeration Circuit with Receiver 10. Refrigeration Circuit with Receiver 268-07 Water--Cooled Condenser with Water Pressure Switch WP Water-Cooled Condenser with Condenser Fan Switch CFSWATER-COOLED Condenser Optional Section Suction Solenoid Override Suction Solenoid ValveOperation Remote Monitoring Optional Safety and Protective Devices Safety and Protective DevicesUnsafe Condition Safety Device Device Setting MICRO-LINK 2i Controller Module Micro-Link 2i Controller/DataCORDER Module Brief Description Operational Software Procedure for loading softwareConfiguration Software Controller Programming Memory Cards Controller Configuration Variables Configuration Title Default Option Number General Layout of the Controller Section KEY Function Display Module Code Title Description Controller Function CodesController Function Code Assignments Inapplicable Functions Display CPC Variable option 34 is set to F refer to Table Code Title Description Controller Alarms Controller Alarm Indications Model 69NT40-511-72ALL Models Check for recharging or replacing battery pack Error Description ERRMicroprocessor Controller Temperature Control Condenser Pressure Control CPC Section Operation in the economy mode Code 34 set to on PRE-TRIP Diagnostics PRE-TRIP Selection Menu Pre-Trip Mode Pre-Trip Test CodesTitle Description Component Normal Logic Crel 3 minutes Seconds Component Normal Logic CrelSeconds Minutes Addition, this test is skipped if Addition, the test will fail if Fail Integrated Datacorder Optional Configuration DataCORDER ConfigurationSetting Factory Default DataCORDER Function Codes Code # Title Description DataCORDER Alarms DataCORDER Alarm Indications DataCORDER Alarm Configurations Description Selection Access to DataCORDER Functions Generic Mode Standard ModeDataCorder Standard Configuration Description Tion USDA/ Message Trip Comment Usda RecordingPre-Trip Data Recording Usda Cold Treatment Procedure DataCORDER Scrollback 10. DataCORDER Pre-Trip Data Test # Title Data Standard Configuration Report Sample SET Point Falling Rising TemperatureCooling AIR Step YES Compressor Cycles OFF Operation PRE-TRIP Inspection Before Starting After Starting Inspection Units equipped with the integrated DataCORDERStarting and Stopping Instructions Unit Operation Controller Set Above --10C +14F, or --5C +23F optionally Defrost indicator will remain on throughout this periodProbe Check Cooling in High Speed with Two-Speed Compressor See Figure 268-07 Control Transformer Cooling in High Speed with Two-Speed Compressor Cooling in Low Speed with Two-Speed Compressor See Figure Cooling in Low Speed with Two-Speed Compressor 268-07 Cooling with Single-Speed Compressor See Figure Cooling with Single-Speed Compressor 268-07 Heating See Figure Heating Mode 268-07 Snap Freeze Option DefrostArctic = 18 Volt Energized Circuit = De-energized Circuit Holding Zone Two-Speed Compressor Holding Zone Unit Runs but has Insufficient Cooling Unit Operates Long or Continuously in Cooling Remedy Unit will not Terminate HeatingUnit will not Defrost Properly Temperature Controller Malfunction Abnormal Noise or VibrationsNo Evaporator AIR Flow or Restricted AIR Flow Power Autotransformer Malfunction WATER-COOLED Condenser or Water Pressure Switch Manifold Gauge SET OpenedClosed Removing the Manifold Gauge Set Blue Hose To Discharge Service orPort Blue Knob Suction and Discharge Service Valves Pumping the Unit DownRefrigerant Leak Checking Evacuation and Dehydration Refrigerant Charge 268-07 Vacuum Pump Connections Adding Refrigerant to System Full Charge Adding Refrigerant to System Partial ChargeCompressor -- Model 06DR Compressor Disassembly Turn off valves on both hoses to pump10 9 8 Jack here Exploded View of Valve Plate Oil Pump and Bearing Head Low Profile Gear Oil Pump 11. Crankshaft Assembly Compressor Reassembly Compression Rings Compressor OIL Level Adding Oil to Service Replacement CompressorIf compressor is without oil To Check the Oil Level in the Compressor To Replace Filter-Drier High Pressure SwitchTo Check Filter-Drier FILTER-DRIER To Replace the Evaporator Fan Assembly To disassemble the Evaporator Fan AssemblyTo Replace the Evaporator Coil Evaporator FAN Motor Capacitors To assemble the Evaporator Fan AssemblyWhen to check for a defective capacitor Removing the capacitor To Replace Condenser Coil Condenser FAN and Motor AssemblyCapacitor analyzer Condenser Coil Ohmmeter Unit RunningUnit Off Saginomiya Recording Thermometer BatteryTo replace the recording thermometer element Calibration Sensor Checkout Procedure AMBS, DTS, RRS, RTS, SRS & STS Maintenance of Painted SurfacesPower Autotransformer Optional Replacing Sensor Probe Replacing Sensor STS and SRS RTS or STSRRS or SRS OLD Style Probe Holder Sensor Mm 1-5/8 inches 35 mm 1/4 inch Sensor Cable Heat Shrink Large Heat Shrink TubingReplacing Sensor RRS and RTS Sensor 25.4 mm 1.0 inch Mounting Stud 35mm 1/4 inch Ambs or DTSReplacing Sensor Ambs or DTS Sensor Crimp Fitting Heat Shrink Crimp FittingTubing Replacing the Coil Coil Checkout ProcedureSuction Solenoid Valve SSV Replacing Valve Internal Parts -- Alco See Figure Thermostatic Expansion Valve Ambient Temperature Cold CoilTo Replace Valve Removing Expansion Valve See Figure Installing Expansion Valve To Measure Superheat CONTROLLER/DATACORDER Removing and Installing the Controller/DataCORDER ModuleRemoval Handling of Controller/DataCORDER Procedure for loading Configuration Software InstallationProcedure for loading Operational Software Controller/DataCORDER Programming Procedure Summary of Procedure What You Will Need Detailed Procedure ReturnPump Fine mesh Support Screen What You Can Do For Further Help Partlow Bulb Temperature-Resistance ChartTemperature Resistance Ohms Ambs and DTS Nonfree Spinning Locknuts ETC Recommended Bolt Torque ValuesBolt DIA Threads Torque MKG Free Spinning Wear Limits For Compressors Compressor Torque Values Temperature Pressure 35F 1.7C Box 0F --17.8C Box Ambient Air Temperature 35F 1.7C Box 0F --17.8C Box35 F 1.7 C Box 17.8 C Box Please Refer to File Diagrams For Schematics and Diagrams Index Index-1 268-07 Index-2 Index-3 268-07 Index-4 Index-5 268-07 Index-6