Corporate Headquarters
Cisco SCE 2000 4/8xFE Installation and Configuration Guide
Version OL-7826-05
Cisco Systems, Inc 170 West Tasman Drive San Jose, CA USA
Cisco SCE 2000 Installation and Configuration Guide
Turn the television or radio antenna until the interference stops
General Overview
C O N T E N T S
Preface
Introduction to the SCE Platform
Installation and Maintenance
Topology
Cabling the Line Ports and Completing the Installation
Connecting the Management Interfaces and Performing Initial System
Configuration
Basic SCE 2000 Platform Operations
Troubleshooting
Index
Preface
Document Revision History
Audience
Organization
Cisco Service Control Application for Broadband User Guide
Cisco Service Control Engine SCE Software Configuration Guide
Cisco Service Control Engine SCE CLI Command Reference
Cisco Service Control Application Reporter User Guide
Conventions
This document uses the following conventions
italic screen font
Documentation CD-ROM
Obtaining Documentation
World Wide Web
Ordering Documentation
Cisco.com
Obtaining Technical Assistance
Documentation Feedback
TechnicalAssistance Center
Contacting TAC by Using the Cisco TAC Website
Contacting TAC by Telephone
Page
Cisco Service Control Capabilities1-2 The SCE Platform
The Cisco Service Control Concept
The Cisco Service Control Concept
General Overview
Cisco Service Control Capabilities
Service Control for Broadband Service Providers
The SCE Platform
Management and Collection
Service Configuration Management
Network Management
Subscriber Management
Data Collection
Introduction to the SCE Platform
Checking the Shipping Container Contents
SCE 2000 Installation Checklist
Front Panel
Refer to Connecting the Line
Ports Connecting the line
ports to the network on page
Power A Power B Status Bypass FE ports
Back Panel
Checking the Shipping Container Contents
Verified
SCE 2000 Installation Checklist
Task
Date
Topology Considerations
Topology
The SCE 2000 Platform
The SCE 2000 Platform Topology Considerations
Functionality
Number of links
Redundancy
Link Continuity
Bypass Mechanism
Physical Topologies
Single SCE 2000 Topologies
Single Link Inline Topology
Single Link Receive-only Topology
Figure 3-2 Single SCE Platform Single Link Receive-Only Topology
Dual link Inline Installation
Figure 3-3 Single SCE Platform Dual Link Inline Topology
Two Cascaded SCE 2000s For Dual Links
Dual Link Receive-Only Topology
Topology-Related Parameters
Two Cascaded SCE 2000s Inline Topology
SCE 2000 Configuration
Connection Mode Parameter
connection-mode command
On-Failure Mode Parameter
Physically Connected Links Parameter
Priority
Preparing to Install the SCE 2000 Platform
Installation and Maintenance
Preparing to Install the SCE 2000 Platform
Installing the SCE 2000 Platform
Tools and Parts Required
Site Requirement Guidelines
Airflow
Site Requirements
Installing the SCE 2000 on a Workbench or Tabletop on page
Installing the SCE 2000 Platform
Installation Precautions on page
Rack-Mounting a SCE 2000 Platform on page
Installation Precautions
Installing the SCE 2000 on a Workbench or Tabletop
Rack-Mounting a SCE 2000 Platform
Attaching the Brackets to the SCE
Attaching the Crossrail Supports to the Rack
Mounting the System to the Rack
Figure 4-8 Sliding the SCE Platform into the Rack
Figure 4-9 Securing the SCE Platform to the Rack
Attaching a Chassis Ground Connection
Figure 4-10 Grounding the Unit AC
Power Supply Overview
LEDs
Table 4-4 IN LED Status for AC-input and DC-input Power Supply Units
OK LED Status for AC-input and DC-input Power Supply Units
Refer to the following tables for LED status information
Removing the Power Supply Unit on page
Removing and Replacing a Power Supply Unit
Power Supply Specifications
Replacing the Power Supply Unit on page
Powering Down the Power Supply Unit and Disconnecting Input Power
Powering Down an AC-Input Power Supply
Powering Down an AC-Input Power Supply on page
Removing the Power Supply Unit
Reconnecting AC-Input Power Supply Unit on page
Replacing the Power Supply Unit
Reconnecting the Power
Reconnecting DC-Input Power Supply Unit on page
Reconnecting AC-Input Power Supply Unit
Reconnecting DC-Input Power Supply Unit
Figure 4-14 Connecting the AC Power
Figure 4-15 Connecting the DC Power
Removing the Fan Module
Fan Module Overview
Removing and Replacing the Fan Module
Removing the Fan Module on page Replacing the Fan Module on page
Replacing the Fan Module
Figure 4-17 Inserting the Fan Module
Replacing the Battery
Connecting the Local Console
Performing Initial System Configuration
Connecting the Local Console
Initial System Configuration
Setting Up the Local Console
Initial System Configuration
Setup Command Parameters
Parameter
Definition
Following are some general instructions regarding the setup dialog
Enter IP address of default gateway
Step 1 Configuring Initial Settings
Would you like to enter the SNMP configuration menu? n
Enter IP address Enter IP subnet mask255.255.0.0
Step 2 Configuring the Hostname
Step 3 Setting the Passwords
Note Passwords are case sensitive
Step 4 Configuring Time Settings
Note The default password for all levels is “cisco”
To configure the time settings, complete the following steps
Step 5 Configuring the DNS Settings
Step 6 Configuring the RDR Formatter Destination
Step 7 ConfiguringAccess Control Lists ACLs
permit any deny
Entry Formats
Order of Entries
deny 10.1.1.0 permit any
Would you like to configure another list? no y
Would you like to enter the Access lists configuration menu? no y
Does this entry permit access? yes
Enter IP address or the word ‘any’ to denote any IP address
When all ACLs have been created, press Enter
Step 8 Configuring SNMP
Step 5 The maximum number of GET communities is
Step 13 The maximum number of trap managers is
Step 9 Configuring the Topology-Dependent Parameters
Bypass - traffic is bypassed using the internal bypass card
To specify Primary, press Enter
Following is a sample topology configuration for a non-redundant inline topology. In this topology, a single SCE 2000 is connected to one or two FE links
Step 10 Completing and Saving the Configuration
To save the configuration to a remote station, type y and press Enter
Connecting the Management Interface
Cabling the Management Port on page
Verifying Management Interface Connectivity on page
Cabling the Management Port
Verifying Management Interface Connectivity
At this point, check that the Link/Active LED is green
Page
Connecting the line ports to the network
Installation
Connecting the line ports to the network
Installing a Cascaded System
Single Link Receive-only Topology on page
Cabling Diagrams
Single Link Inline Topology on page
Dual Link Single SCE 2000 Topologies on page
In the single link inline topology, either the first FE link FE-1 SUB/NET of the SCE 2000 or the second FE link FE-2 SUB/NET can be used, as illustrated in the diagram above. The remaining ports are unused
Single Link Receive-only Topology
Dual Link Single SCE 2000 Topologies
Dual Link Two SCE 2000s Topology
SCE 2000 #1
SCE 2000 #2
Connecting the FE Line Interface Ports
Cabling the FE Line Port
Testing Connectivity Examining Link LEDs and Counters
Examining the Link LEDs
counters
To view the Fast Ethernet port status, complete the following steps
Installing a Cascaded System
Use the show interface linecard 0 connection-mode command
Use the show interface linecard 0 link mode command
CLI Commands for Cascaded Systems
Configuring the Connection Mode
Topology-Related Parameters for Redundant Topologies
Link Mode
Monitoring the System
forwardingbypasssniffingcutoff and press Enter
Loading and Activating a Service Control Application
Service Control Application for Broadband User Guide
Service Control Application for Broadband Reference Guide
Page
Rebooting and Shutting Down the SCE Platform
Managing SCE 2000 Configurations
Performing Complex Configurations
Basic SCE 2000 Platform Operations
Starting the System and Observing Initial Conditions
Viewing the User Log Counters
Final Tests
Verifying Operational Status
Verifying Operational Status on page
Viewing Configuration on page
Managing SCE 2000 Configurations
Viewing Configuration
Saving the Configuration Settings on page
Saving the Configuration Settings
Step 3 Type copy running-config startup-config
Recovering a Previous Configuration
Cisco Service Control Engine SCE Software Configuration Guide
Performing Complex Configurations
copy tffs0system/prevconf/config.tx1 tffs0system/config.txt
Cisco Service Control Engine SCE CLI Command Reference
Displaying the SCE Platform Version Information
CLI show inventory command
Displaying the SCE Platform Inventory
Rebooting and Shutting Down the SCE Platform
Rebooting the SCE Platform
Displaying the System Uptime
Shutting Down the SCE Platform
y IT IS NOW SAFE TO TURN THE POWER OFF
SCE 2000#reload shutdown You are about to shut down the system
Page
Troubleshooting Overview8-1
Troubleshooting
Troubleshooting Overview
Troubleshooting Tools
CLI Commands for Troubleshooting on page The User Log on page
Troubleshooting Tools
CLI Commands for Troubleshooting
Check the LEDs on page
Troubleshooting the management subsystem
Troubleshooting the link interface subsystem
The User Log
The Logging System
Clearing the User Log
Copying the User Log
Viewing the User Log
From the SCE 2000# prompt, type logger get user-log file-name
Viewing the User Log Counters
SCE 2000 Operational Status
Check the LEDs
Generating a File for Technical Support
SCE 2000 Operational Status on page
Problem Solving Using a Subsystems Approach
Identifying Startup Problems
Troubleshooting the Power Subsystem
Troubleshooting the Firmware Package Installation
File not found in the expected location Wrong file type
Device to which the file is to be extracted is full
Management link is down. Mng LINK LED not lit--also Status is WARNING
Troubleshooting the Management Subsystem
Problems in the management subsystem could be any of the following
Management link is up Mng LINK LED lit but does not answer ping
Interface Mng 0/1 0/2
show ip default
Troubleshooting the Management Subsystem
active-port
Troubleshooting the Link Interface Subsystem
Link is down. LINK LED not lit and system status is WARNING
Troubleshooting the Link Interface Subsystem
at the SCE 2000 but enabled
Auto-negotiation is disabled
Check auto-negotiation configuration
Chapter 8 Troubleshooting Problem Solving Using a Subsystems Approach
Page
Index
