Delta Electronics 230V Series, 460V Series, 115V Series manual Appendix a Specifications

Appendix A Specifications

		Voltage Class		115V Class				230V Class					460V Class
	Model Number VFD-XXXS			002	004	007	002	004	007	015	022	004	007	015	022
	Max. Applicable Motor Output (kW)			0.2	0.4	0.75	0.2	0.4	0.75	1.5	2.2	0.4	0.75	1.5	2.2
	Max. Applicable Motor Output (HP)			0.25	0.5	1.0	0.25	0.5	1.0	2.0	3.0	0.5	1.0	2.0	3.0
	Rating	Rated Output Capacity (KVA)		0.6	1.0	1.6	0.6	1.0	1.6	2.9	4.2	1.2	2.0	3.3	4.4
		Rated Output Current (A)		1.6	2.5	4.2	1.6	2.5	4.2	7.5	11.0	1.5	2.5	4.2	5.5
				3-phase
				Proportional to
	Output	Maximum Output Voltage (V)					3-phase Proportional to Input Voltage
				Twice the Input
				Voltage
		Rated Frequency (Hz)		1.0 to 400 Hz
		Rated Input Current (A)		Single phase			Single/3-phase model drive					3-phase
	Rating			6	9	18	4.9/	6.5/	9.7/	15.7/	24/	1.7	2.9	5.1	6.9
							1.9	2.7	5.1	9.0	15
		Input Current for 1-phase model			-- --		1.6	3.0	5.1	8.4	--		-- --
		drive to be used as 3-phase
	Input
		model drive
		Rated Voltage/Frequency		100/110/120 VAC			200/208/220/240 VAC					380/400/415/480 VAC
				50/60 Hz			50/60Hz					50/60Hz
		Voltage/Freq. Tolerance		Voltage: ±10%,			Frequency: ±5%
		Control System		SPWM (Sinusoidal Pulse Width Modulation, carrier frequency 3k-10kHz)
	Control Characteristics	Output Frequency Resolution		0.1Hz
		Torque Characteristics		Including the auto-torque, auto-slip compensation; starting torque can be
				150% at 5Hz
		Overload Endurance		150% of rated current for 1 minute
		Accel/Decel Time		0.1to 600 second (2 Independent settings for Accel/Decel Time)
		V/F Pattern		V/F pattern adjustable
		Stall Prevention Level		20 to 250%, Setting of Rated Current
			Keypad	Setting by				or Potentiometer
		Frequency
			External	Potentiometer-5KΩ/0.5W, DC 0 to +10V or 0 to +5V (Input impedance
	Characteristics	Setting
				47KΩ), RS-485 interface, 4 to 20mA (Input impedance 250Ω); Multi-
			Signal
				Function Inputs 1 to 5 (7 steps, Jog, up/down)
		Operation	Keypad	Setting by RUN, STOP
			External	M0 to M5 can be combined to offer various modes of operation, RS-485
		Setting Signal
			Signal	serial interface (MODBUS).
	Operating	Multi-Function Input Signal		Multi-step selection 0 to7, Jog, accel/decel inhibit, first/second accel/decel
				switch, counter, 8-step PLC operation, external Base Block (NC, NO),
				increase/decrease Master Frequency
		Multi-Function Output Indication		AC Drive Operating, Frequency Attained, Non-zero, Base Block, Fault
				Indication, Local/Remote indication, PLC Operation indication.
		Analog Output Signal		Analog frequency/current signal output.
				AVR, S-Curve, Over-Voltage/Over-Current Stall Prevention, Fault Records,
	Other Function			Adjustable Carrier Frequency, DC Braking, Start Frequency for DC Braking,
				Momentary Power Loss restart, Frequency Limits, Parameter Lock/Reset,
				PID Feedback Control, Reverse Inhibition, etc.
	Built-in EMI Filter			VFD002S21E, VFD004S21E, VFD004S43E, VFD007S21E, VFD007S43E,
				VFD015S21E, VFD015S43E, VFD022S21E, VFD022S43E
	Protection			Self-testing, Over Voltage, Over Current, Under Voltage, Overload,
				Overheating, External Fault, Electronic thermal, Ground Fault.
	Cooling			Forced air-cooling (ONLY FOR 022S2XA/B; XXXS43A/B/E 1HP~3HP;
				XXXSXXD; XXXS21E 400W~3HP). Others are Natural air-cooling.
Revision August 2006, SE08, SW V2.61