Preparation for use and operation, Control panel | Fujitsu N800

4 Preparation for use and operation

VCAUTION!

Observe the safety information in the chapter “Important notes” on page 11.

4.1Controls and indicators

4.1.1Control panel

The control panel is located on the front of the server between the fan cage and the drive cage.

		P R IM E R G Y	N
!	!	!

Figure 12: Front view

U41243-J-Z156-1-76

33

Image 41

Fujitsu N800 manual Preparation for use and operation, Controls and indicators, Control panel

Contents

Primergy N800 Server System Copyright and Trademarks Comments… Suggestions… Corrections…Page Page Contents Configuration software and utilities Contents 105 Page Introduction Features FeaturesExternally accessible drives Processors and Memory Introduction Power supplyCooling Hot-plug PCI ServerStart Server management Target group Service and SupportOther features Summary of contents Notational conventions Scsi configurationsSystem expansions Bold type User-friendly documentation verified quality User-friendly documentation verified quality Dimensions and weight Technical dataElectrical data Environmental conditions according to DIN EN Noise level ISO Operation Idle Technical dataStandards Important notes Important notes Electrostatic-sensitive component sticker Electrostatic-sensitive component label RFI suppression CE certificateFCC notices Federal Communications Commission CE certificate Important notes Environmentally friendly product design and development Environmental protectionEnvironmental protection Further information on environmental protection Take-back, recycling and disposalPage Unpacking the server Installing the server Mounting the server in the rack Mounting the installation kit and the serverMounting the server in the rack Mounting the server in the rack Mounting the system brackets Press in the safety springs 1 on both telescopic rails Mounting the articulated cable guide Disconnecting cables Connecting and disconnecting cablesConnecting cables Inch Rack Routing cablesRouting cables Routing the cables in the DataCenter Rack DataCenter Rack Universal ports Connecting devices to the serverConnecting devices to the server Can bus connection PCI can bus controller ServerView and the can bus RemoteView RTDS, Seman and the can bus Connecting the server to line voltagePage Control panel Controls and indicatorsPreparation for use and operation Drive error Controls and indicators Controls and indicators for the CD-ROM drive Indicators for the internal Scsi drivesControls and indicators for the floppy disk drive Indicators for the power supplies Rear view of server Rear view Switching the server on and off Configuring the server and components Installing the operating systemInstalling the operating system Switch Function Description Pos Changing the switch settings A r Id e Meaning Lupk Password Clear Cleaning the serverPage Short cuts using a key combinations Configuration software and utilitiesPower-ON Self-Test Post Key combinations Power-ON Self-Test Post You cannot call Bios Setup Bios SetupRecording Setup settings Bios Setup Starting Bios Setup Display Meaning Setup menusPos Main menu Submenu Key Meaning Main Menu DisabledMenu item Option Description 44/1,25 MB, 3 ½ Auto English US Menu item Description Option DescriptionProcessor Information submenu Sec Keyboard Features submenu Menu item Option Description30/sec Minimum EnabledAdvanced Menu PCI PCI Configuration submenu Menu item Option Description 0080h PCI Mode submenu Menu item Option Description Bidirectional 3F82F8 DMA 378h Causes the secondary cache to be Clear Security Menu Secure Mode Boot Direct Connect Server Menu System Management submenu Menu item Option Description Enable 9600 Server Management Information submenuConsole Redirection submenu Menu item Option Description Boot Menu Exit Menu Bios Setup Menu item Option Description Utilities System Setup Utility SSUUtilities Recording the current Bios settings Bios updateCreating bootable floppy disks Preparations Example Bios and firmware update Changing the Bios language Recovering Bios Installing PCI hot-plug software Installing graphic driversQLogic Scsi utility Running the Scsi utility Property and data protection Password protectionSecure boot mode Boot without keyboard Boot sequence controlLocking the power and reset buttons Floppy disk write protection Power-on indicator remains dark Troubleshooting and tipsPower cable incorrectly connected Power supply overloaded Screen remains dark Server switches itself off No screen display or display drifts Flickering stripes on the monitor screenNo mouse pointer displayed on the screen Monitor does not support the set horizontal frequency Scsi configuration incorrect Ultra Wide Scsi controller System will not bootFloppy disk cannot be read/written Time and date are not correct Configuration of the disk array controller is incorrect Error messages on the screenDrives are reported as dead Added drive reported defective Code Error message Error messages on the LCD displayError messages on the LCD display Error messages on the LCD display Error messages on the LCD display Code Error message Error messages on the LCD display Removing the front bezel System expansionsOpening/closing the server Opening/closing the server Mounting the front bezel Removing the PCI bus hot-plug cover Removing/mounting the PCI bus hot-plug cover Removing the top cover Removing/mounting the top cover Scsi hard disk drives Scsi hard disk drives S y Fault LED Replacing Scsi hard disk drives Removing a hard disk drive System expansions Power supply units Power supply units LED Replacing a power supply unit Fans System expansions Fans Fans Replacing a fan Removing a fan Fans System expansions PCI locking mechanism Boards in hot-plug PCI slot Boards in hot-plug PCI slot LED indicatorsVoltage Status description Emergency-off status Normal status Replacing boards in the hot-plug PCI slot Release the PCI locking mechanism and remove the board 103 Removing the PCI slot cover Adding a PCI board Processor expansion Processor unit and FSB terminator Processor expansion Removing the processor fastener U41243-J-Z156-1-76 Removing/installing processor units Memory expansion Memory expansion Need to be installed in pairs Single port mode one memory module The single memory module Step Occupied sockets Installing DIMMs 111 Removing the memory module cover Removing a memory module 113 RemoteView storage medium Installing a memory moduleRemoteView storage medium Configuring the RemoteView storage medium Remote Service Board Remote Service Board Addresses for Scsi devices Scsi configurationsConfiguration SCSI-IDs Configuration with dual onboard Scsi controller default Internal Scsi configurationsInternal Scsi configurations Abbreviations Abbreviations HSC PCI SEL Page Can Multi Mode Faser Safety, Warranty and Ergonomics Zoll-Rack/19 Inch RackRelated publications Primergy S40-DF Storage Subsystem Operating manualPage Index Bios Mains IndicatorIndex 129 Height units Mounting in the rack ON/OFF switch Ports Comments Suggestions Corrections Page Comments Suggestions Corrections