Huawei MC509 15.3 Final Result Codes

HUAWEI MC509 CDMA LGA Module

AT Command Interface Specification

Appendix

Issue 01 (2011-08-26)

Huawei Proprietary and Confidential

151

The causes are as follows:

2: NV error

4: operation not allowed

6: incorrect parameter

10: R-UIM wrong

11: R-UIM busy

12: memory failure

13: invalid index

14: memory full

18: no short message to be acknowledged

19: unknown

15.3 Final Result Codes

Final result code

No.

Description

A command is executed, and there

is no error.

CONNECT

A connection is established.

RING

An incoming call is originated.

NO CARRIER

A connection is terminated.

ERROR

There is a common error.

NO DIALTONE

There is no dialing tone.

BUSY

The peer is busy.

NO ANSWER

Timeout occurs when the

connection is complete, and there

is no reply.

+CME ERROR: <err>

The error type is specified by

<err>.

+CMS ERROR: <err>

It is a short message-related error.

The final result code is the termination flag of an AT command.

Contents

Main AT Command Interface Specification Huawei Technologies Co., Ltd. Copyright Huawei Technologies Co., Ltd. 2011. All rights reserved. Trademarks and Permissions Notice NO WARRANTY About This Document History Contents Page Page Page Page Page Page Page Page Page Page Page Page 1 1.1 Content Description 1.2 Product Description 1.3 Instructions for Use 1.4 Overview of AT Command Interfaces 1.4.1 Description of AT Commands information response to +CMD2? shows acceptable ranges of each subparameter 1.4.2 Types of AT Commands Page Page 1.4.3 Abort Attributes of AT Commands 1.4.4 Rules for Running AT Commands 1.5 Organization of This Document Page 2 2.1 EEcho Command 2.1.1 Syntax 2.1.2 Interface Description 2.1.3 Parameter Description 2.2 S3Command Line Termination Character 2.2.1 Syntax 2.2.2 Interface Description 2.2.3 Parameter Description 2.3 S4Response Format Character 2.4 S5Backspace Character 2.4.1 Syntax 2.4.2 Interface Description 2.4.3 Parameter Description 2.5 VCommand for Setting the Response Format 2.5.1 Syntax 2.5.2 Interface Description 2.5.3 Parameter Description 2.6 QCommand for Controlling Return of the Execution Result 2.6.1 Syntax 2.6.2 Interface Description 2.6.3 Parameter Description 2.7 &FCommand for Restoring Factory Settings 2.8 &VCommand for Querying the Current Configuration 2.8.1 Syntax 2.8.2 Interface Description 2.9 A/Command for Repeating the Previous Command 2.9.1 Syntax 2.9.2 Interface Description 2.9.3 Example 2.10 +CMEECommand for Setting the Error Report Format 2.10.1 Syntax 2.10.2 Interface Description 2.10.3 Parameter Description 2.11 +CFUNCommand for Setting the Operating Mode 2.11.1 Syntax 2.11.2 Interface Description 2.11.3 Parameter Description 2.12 ^VOLTCommand for Querying the voltage 2.12.1 Syntax 2.12.2 Interface Description 2.12.3 Parameter Description 2.13 ^RESET - Command for Delaying the Module Reset Function 2.14 ^MSOShutdown Command 2.14.1 Syntax 2.14.2 Interface Description 2.15 ^HSCommand for Shaking Hands with the TE 2.15.1 Syntax 2.15.4 Example 3 3.1 ICommand for Querying Product Identity Information 3.1.1 Syntax 3.1.2 Interface Description 3.1.3 Parameter Description 3.1.4 Example 3.2 +CGMI/+GMICommand for Querying Manufacturer Information 3.2.1 Syntax 3.2.2 Interface Description 3.2.3 Parameter Description 3.2.4 Example 3.3 +CGMM/+GMMCommand for Querying Product Name 3.3.1 Syntax 3.3.2 Interface Description 3.3.3 Parameter Description 3.3.4 Example 3.5 +GSNCommand for Querying the ESN 3.5.1 Syntax 3.5.2 Interface Description 3.5.3 Parameter Description 3.5.4 Example 3.6 +CGSNCommand for Querying the ESN 3.6.1 Syntax 3.6.2 Interface Description 3.6.3 Parameter Description 3.6.4 Example 3.7 ^HWVERCommand for Querying the Hardware Version 3.7.1 Syntax 3.7.2 Interface Description 3.7.3 Parameter Description 3.8 ^MEIDCommand for Querying the MEID 3.9 +CIMICommand for Querying the IMSI 3.9.1 Syntax 3.9.2 Interface Description 3.9.3 Parameter Description 3.10 ^ICCIDCommand for Querying the ICCID 3.11 ^MDNCommand for Querying the MDN 3.11.1 Syntax 3.11.2 Interface Description 3.11.3 Parameter Description 3.11.4 Example 4 4.1 +CLCKCommand for Enabling the PIN and Querying the Status 4.1.1 Syntax 4.1.2 Interface Description 4.1.3 Parameter Description 4.2 +CPINPIN Management Command 4.2.1 Syntax 4.2.2 Interface Description 4.2.3 Parameter Description 4.3 ^CPINPIN Extension Management Command 4.3.1 Syntax 4.3.2 Interface Description 4.3.3 Parameter Description 4.4 +CPWDCommand for Changing the Password 4.4.1 Syntax 4.4.2 Interface Description 4.4.3 Parameter Description 4.4.4 Example 5 5.1 &CCommand for Setting the Changing Mode of DCD Signals 5.1.1 Syntax 5.1.2 Interface Description 5.1.3 Parameter Description 5.2 &DCommand for Setting the MT Action in Response to the DTR Signals 5.2.1 Syntax 5.2.2 Interface Description 5.2.3 Parameter Description 5.3 &SCommand for Setting the Changing Mode of DSR Signals 5.4 +ICFCommand for Setting the Character Frame Format 5.4.1 Syntax 5.4.2 Interface Description 5.4.3 Parameter Description 5.5 +IPRCommand for Setting the Fixed Baud Rate 5.5.1 Syntax 5.5.2 Interface Description 5.5.3 Parameter Description 5.6 +IFCCommand for Setting Flow Control 5.6.1 Syntax 5.6.2 Interface Description 5.6.3 Parameter Description Page 6 6.1 ^SIMSTchange of uim state instructions 6.1.1 Syntax 6.1.2 Interface Description When the uim state changes, 6.1.3 Parameter Description 6.2 ^SYSINFOCommand for Querying System Information 6.2.1 Syntax 6.2.2 Interface Description 6.2.3 Parameter Description 6.3 ^DSDORMANTInstructions into the dormant 6.3.1 Syntax 6.3.2 Interface Description 6.3.3 Parameter Description 6.4 ^MODECommand for Indicating the System Mode Change 6.4.1 Syntax 6.4.2 Interface Description 6.4.3 Parameter Description 6.5 ^PREFMODECommand for setting the network mode 6.6 ^rfswitchCommand for Setting the Flight Mode 6.6.1 Syntax 6.6.2 Interface Description 6.6.3 Parameter Description 6.6.4 Example 6.7 +CSQCommand for Querying the RSSI 6.7.1 Syntax 6.7.2 Interface Description 6.7.3 Parameter Description 6.8 ^RSSILVLCommand for Reporting the RSSI 6.8.1 Syntax 6.8.2 Interface Description 6.8.3 Parameter Description 6.9 ^HRSSILVLCommand for Reporting the HDR RSSI 6.9.1 Syntax 6.9.2 Interface Description 6.9.3 Parameter Description 6.10 ^RSSIREPCommand for Setting the Reporting of the RSSI 6.11 ^CRSSICommand for Reporting the RSSI 6.11.1 Syntax 6.11.2 Interface Description 6.11.3 Parameter Description 6.12 ^HDRRSSICommand for Reporting the HDR RSSI 6.12.1 Syntax 6.12.2 Interface Description 6.12.3 Parameter Description 6.13 ^TIMECommand for Querying the System Time on the Network Side 6.14 ^COTKSLACTCommand for Defining a Subscriber 6.14.1 Syntax 6.14.2 Interface Description 6.14.3 Parameter Description 6.15 ^OTAACTEDCommand for Querying the OTA Activation Status 6.15.1 Syntax 6.15.2 Interface Description 6.15.3 Parameter Description 6.16 ^OTACMSGCommand for Indicating the OTA Update Status 6.17 ^CURRSIDCommand for Query SID of The Current System 6.17.1 Syntax 6.17.2 Interface Description 6.17.3 Parameter Description 6.17.4 Example Page 7 7.1 DCommand for Originating a Data Service Call 7.1.1 Syntax 7.1.2 Interface Description 7.1.3 Parameter Description 7.1.4 Example 7.2 HCommand for Disconnecting the Data Service 7.2.1 Syntax 7.2.2 Interface Description 7.2.3 Parameter Description 7.3 +CDVCommand for Originating a Voice Call 7.4 +CHVCommand for Disconnecting a Voice Call 7.4.1 Syntax 7.4.2 Interface Description 7.4.3 Parameter Description 7.5 ACommand for Answering a Call A 7.6 RINGCommand for Indicating a Call 7.6.1 Syntax 7.6.2 Interface Description 7.7 S0Command for Setting Automatic Answer 7.7.1 Syntax 7.8 ^ORIGCommand for Indicating the Origination of a Call 7.8.1 Syntax 7.8.2 Interface Description 7.8.3 Parameter Description 7.9 ^CONNCommand for Indicating a Call Connection 7.10 ^CENDCommand for Indicating the End of a Call 7.10.1 Syntax 7.10.2 Interface Description 7.10.3 Parameter Description 7.11 +CLIPCommand for Setting the Presentation of Caller ID 7.11.1 Syntax 7.11.2 Interface Description 7.11.3 Parameter Description 7.11.4 Example 7.12 +CLCCCommand for Querying the Call Status 7.12.1 Syntax 7.12.2 Interface Description 7.12.3 Parameter Description 7.12.4 Example 7.13 ^DTMFTwo-Stage Dialing Command 7.13.1 Syntax 7.13.2 Interface Description 7.13.3 Parameter Description 7.13.4 Example 7.14 ^PPPCFGCommand for Setting the PPP User Name and Password 7.14.1 Syntax 7.14.2 Interface Description 7.14.3 Parameter Description 7.14.4 Example 7.15 +CTACommand for Setting operating mode 7.15.1 Syntax 7.15.2 Interface Description 7.15.3 Parameter Description <cta>: the time to enter the dormant. 8 8.1 +CPMSCommand for Setting the Short Message Storage Location 8.1.1 Syntax 8.1.2 Interface Description 8.1.3 Parameter Description 8.2 +CNMICommand for Setting the Mode of New Short Message Notification 8.2.1 Syntax 8.2.2 Interface Description 8.2.3 Parameter Description Page 8.2.4 Example 8.3 +CMTICommand for Indicating the Arrival of a Short Message 8.3.1 Syntax 8.3.2 Interface Description 8.3.3 Parameter Description 8.4 ^HCMTCommand for Reporting a New Short Message 8.4.1 Syntax 8.4.2 Interface Description 8.4.3 Parameter Description 8.5 +CDSICommand for Indicating the Arrival of a Status Report Short Message 8.5.1 Syntax 8.5.2 Interface Description 8.5.3 Parameter Description 8.6 ^HCDSCommand for Reporting a New Status Report Short Message 8.6.1 Syntax 8.6.2 Interface Description 8.6.3 Parameter Description Page 8.7 +CNMACommand for Acknowledging a New Short Message 8.7.1 Syntax 8.7.3 Parameter Description 8.7.2 Interface Description 8.8 ^HSMSSSCommand for Setting Short Message Parameters 8.8.1 Syntax 8.8.2 Interface Description 8.8.3 Parameter Description 8.9 ^HCMGSCommand for Sending a Short Message 8.9.1 Syntax 8.9.2 Interface Description 8.9.3 Parameter Description 8.10 ^HCMGSSCommand for Reporting Successful Short Message Sending 8.10.1 Syntax 8.10.2 Interface Description 8.10.3 Parameter Description 8.11 ^HCMGSFCommand for Reporting Short Message Sending Failure 8.11.3 Parameter Description 8.12 ^HCMGWCommand for Storing a Short Message 8.12.1 Syntax 8.12.2 Interface Description 8.12.3 Parameter Description Page 8.12.4 Example 8.13 ^HCMGLShort Message List Command 8.13.1 Syntax 8.13.2 Interface Description 8.13.3 Parameter Description 8.14 ^HCMGRCommand for Reading a Short Message 8.14.1 Syntax 8.14.2 Interface Description 8.14.3 Parameter Description Page 8.15 +CMGDCommand for Deleting a Short Message 8.15.1 Syntax 8.15.2 Interface Description 8.15.3 Parameter Description 8.16 ^SMMEMFULLCommand for Reporting Full of Short Messages on a Storage Medium 8.16.1 Syntax 8.16.2 Interface Description 8.16.3 Parameter Description 8.17 +CMGF Command for Set Message Format 8.17.2 Interface Description 8.17.3 Parameter Description 9 9.1 +CPBSCommand for Selecting a Phonebook Memory 9.1.1 Syntax 9.1.2 Interface Description 9.1.3 Parameter Description 9.2 ^CPBRCommand for Reading the Phonebook 9.2.1 Syntax 9.2.2 Interface Description 9.2.3 Parameter Description 9.3 ^CPBWCommand for Writing Entries to the Phonebook 9.3.1 Syntax 9.3.2 Interface Description 9.3.3 Parameter Description 9.3.4 Example 10 10.1 ^IPINITCommand for Initializing a TCP/UDP Connection 10.1.1 Syntax 10.1.2 Interface Description 10.1.3 Parameter Description 10.1.4 Example 10.2 ^IPOPENCommand for Establishing a TCP/UDP Connection 10.2.1 Syntax 10.2.2 Interface Description 10.2.3 Parameter Description 10.2.4 Example 10.3 ^IPLISTENCommand for Enabling Server Listening 10.3.1 Syntax 10.3.2 Interface Description 10.3.3 Parameter Description 10.3.4 Example 10.4 ^IPSENDCommand for Transmitting TCP/UDP Data 10.4.1 Syntax 10.4.2 Interface Description 10.4.3 Parameter Description 10.4.4 Example 10.5 ^IPGETDATACommand for Querying the TCP/UDP Data Receiving Buffer 10.5.1 Syntax 10.5.2 Interface Description 10.5.3 Parameter Description 10.5.4 Example 10.6 ^IPDATACommand for Indicating the Arrival of TCP/UDP Data 10.6.1 Syntax 10.6.2 Interface Description 10.6.3 Parameter Description 10.6.4 Example 10.7 ^IPCLOSECommand for Disabling a TCP/UDP Connection 10.7.1 Syntax 10.7.2 Interface Description 10.7.3 Parameter Description 10.7.4 Example 10.8 ^IPENTRANSCommand for Enabling the Transparent Transmission Mode 10.8.1 Syntax 10.8.2 Interface Description 10.8.3 Parameter Description 10.8.4 Example 11 11.1 ^SWSPATH -Switch Sound Path 11.1.1 Command Syntax 11.1.2 Description 11.1.3 Defined Values 11.2 ^CPCM-Configure PCM audio 11.2.1 Description 11.2.2 Defined Values 11.3 +CMIC -Tune microphone gain level 11.3.1 Command Syntax 11.3.2 Description 11.3.3 Defined values 11.4 +CLVL -Tune loudspeaker volume level 11.5 +CMUT -Switch mute status 11.5.1 command syntax 11.5.2 Description 11.5.3 Defined values 11.6 ^SMUT -Switch speaker mute status 11.6.1 Command syntax 11.6.2 Description 11.6.3 Defined values 12 12.1 ^WAKEUPCFG -Wakeup Function Configuration 12.1.1 Command Syntax 12.1.2 Description 12.1.3 Defined Values 12.1.4 Example 12.2 ^CURC -Unsolicited report control command 12.2.1 Command Syntax 12.2.2 Interface Description 12.2.3 Defined Values 13 13.1 ^BODYSARONDisable or Enable Body SAR 13.1.1 Syntax 13.1.2 Interface Description 13.1.3 Parameter Description 13.2 ^BODYSARCDMA Set the max tx Power Limit of CDMA 13.2.1 Syntax 13.2.2 Interface Description 13.2.3 Parameter Description 13.3 ^THERMThermal Protection Activated Usolicited Report 13.3.2 Interface Description 13.3.3 Parameter Description 14 14.1 ^WPDOMCommand for Setting Operation Mode 14.1.1 Syntax 14.1.2 Interface Description 14.1.3 Parameter Description Page 14.2 ^WPDSTCommand for Setting Session Type 14.2.1 Syntax 14.2.2 Interface Description 14.2.3 Parameter Description 14.3 ^WPDFRCommand for Setting Fix Rate 14.3.1 Syntax 14.3.2 Interface Description 14.3.3 Parameter Description 14.4 ^WPQOSCommand for Setting Fix QoS 14.4.1 Syntax 14.4.2 Interface Description 14.4.3 Parameter Description 14.5 ^WPDGPCommand for Starting GPS Position 14.5.1 Syntax 14.5.2 Interface Description 14.5.3 Parameter Description 14.6 ^WPENDCommand for ending GPS Position 14.7 ^POSITIONCommand for Reporting Position Result 14.7.1 Syntax 14.7.2 Interface Description 14.7.3 Parameter Description 14.7.4 Example 14.8 ^POSENDCommand for Reporting Position End 14.8.1 Syntax 14.8.2 Interface Description 14.8.3 Parameter Description Page 14.9 ^WPDIMCommand for Deleting Assisted Data 14.9.1 Syntax 14.9.2 Interface Description 14.9.3 Parameter Description 14.10 ^GPSTYPECommand for Quering GPS Type 14.10.1 Syntax 14.10.2 Interface Description 14.10.3 Parameter Description 14.10.4 Example 15 15.1 CME ERROR List Page Page Page 15.2 CMS ERROR List 15.3 Final Result Codes 15.4 Initial Values of Command Parameters After MT Restart 15.5 Phone Number Type Page 15.6 AT Commands That Are Allowed to Be Executed in PIN Code Limit Mode 15.7 Acronyms and Abbreviations