SNMP

Table 63. Cmm Location (1.3.6.1.4.1.343.2.14.2.10.3) (Sheet 1 of 3)

OID

Object

Syntax

Access

Value

 

 

 

 

 

1

softwareVersion

DisplayString

read-only

The version of the CMM software.

 

 

 

 

 

2

cmmRedundancy

DisplayString

read-only

cmm redundancy information.

 

 

 

 

 

3

rmcpEnabled

INTEGER

read-write

Enable or disable the RMCP Service:

disable(0), enable(1)

 

 

 

 

 

4

cmmGrantedBoardEkeys

DisplayString

read-only

Get the Ekeys that have been granted

to the location.

 

 

 

 

 

 

 

 

 

5

cmmTotalFrus

DisplayString

read-only

display the total number of FRUs.

 

 

 

 

 

6

cmmPICMGProperties

DisplayString

read-only

 

 

 

 

 

 

7

cmmDeviceID

DisplayString

read-only

 

 

 

 

 

 

 

 

 

 

Used to find out if a location is present

8

cmmPresence

INTEGER

read-only

in the chassis.1 - Present 0 - Not

 

 

 

 

present

 

 

 

 

 

 

 

 

 

Used to find out what targets are

9

cmmListTargets

DisplayString

read-only

available on a location (e.g., getting the

 

 

 

 

list of sensors in the chassis).

 

 

 

 

 

10

cmmListDataItems

DisplayString

read-only

Used to find out what data items are

available on a target or location.

 

 

 

 

 

 

 

 

 

 

 

 

 

Health information about a particular

11

cmmHealth

INTEGER

read-only

location. This will be one of the

following: (0-OK, 1-Minor, 2-Major, 3-

 

 

 

 

 

 

 

 

Critical)

 

 

 

 

 

 

 

 

 

Events that contribute to the health of

12

cmmHealthEvents

DisplayString

read-only

the location. This is a list of events

 

 

 

 

happening on the location.

 

 

 

 

 

13

cmmSNMPEnable

INTEGER

read-write

Used to set or query SNMP trap

enabled status.

 

 

 

 

 

14 -

CmmSNMPTrapAddressN

IP Address

read-write

The IP address of the machine that will

18

receive SNMP traps from a location.

 

 

 

 

 

19

cmmSNMPTrapCommunity

DisplayString

read-write

SNMP community name (max 64

 

 

 

 

characters).

20

cmmSNMPTrapVersion

DisplayString

read-write

v1 or v3

 

 

 

 

 

21

cmmSNMPTrapPort

DisplayString

read-write

SNMP trap port.

 

 

 

 

 

 

 

 

 

Get/Set the color of the fault/health LED

22

cmmFaultLEDColor

DisplayString

read-write

on the CMM fronted FRUsto be used

when an error is reported. Values:

 

 

 

 

“amber” or “red”.

 

 

 

 

 

 

 

 

 

The Telco Alarm cutoff. When enabled,

 

 

 

 

it silences the Telco alarm for active

 

 

 

 

events and blinks the event LEDs on

23

cmmAlarmCutoff

INTEGER

read-write

the CMM. This dataitem is only valid

 

 

 

 

when used with the cmm as the location

 

 

 

 

and is used to set the alarm cutoff or

 

 

 

 

get its value. 1 - Set, 0 - Clear.

 

 

 

 

 

146MPCMM0001 Chassis Management Module Software Technical Product Specification

Page 146
Image 146
Intel MPCMM0001 manual Cmm Location 1.3.6.1.4.1.343.2.14.2.10.3 Sheet 1