Manuals / JVC / Computer Equipment / Projector

JVC 250 Convergence Deflection PCB, Horizontal Vertical Deflection PCB - Remove and Replace

Models: 250

1 190

Download 190 pages 59.74 Kb

Page 83

Horizontal Vertical Deflection PCB - Remove and Replace

Chapter 5---Electronics

Horizontal Vertical Deflection PCB - Remove and Replace

The Horizontal/Vertical (H/V) Deflection PCB is located in the upper portion of the Electronic Module card cage.

Tools Needed:

#1 Pozi-drive Phillips-head screwdriver

Parts Needed:

Horizontal Vertical Deflection PCB p/n 105236

To remove the Horizontal/Vertical (H/V) Deflection PCB:

1.Power off the projector by IR Remote or PC, and allow the cooling fans to run until they shut off automatically.

2.Turn the AC Circuit Breaker to the OFF position and unplug the AC Power Cord.

3.Remove the rear cover.

4.Disconnect six connectors; J34, J35, J36, J41, J42, and J43 (see Figure 5-15). Move the cables out of the way.

5.Loosen (it is not necessary to remove) the 5 Pozi-drive Phillips-head screws that secure the Horizontal Vertical Deflection PCB to the electronic module cage.

6.Remove the Horizontal Vertical Deflection PCB by sliding it toward the left side of the projector (this is the upward direction if the electronic module is tilted up) so that the mounting screws clear the access holes. Then lift the side of the PCB that is nearest the front of the projector first and angle it upward so that the side closest to the rear clears the lip of the electronic module frame. Be careful when removing or reinstalling the PCB to avoid damaging it on the fan screws or cable clamps.

7.Reinstall the Horizontal Vertical Deflection PCB by lowering the side that is nearest to the rear of the projector in first until it clears the electronic module edge, then lowering the other side. Carefully fit the board over the mounting screws and slide the board into position. Tighten the screws and reconnect the connectors.

5.7Convergence Deflection PCB

Convergence Deflection PCB - Main Functions

!Generation of various waveforms for the horizontal and vertical deflection.

!Height control

!Generation of waveforms for dynamic focus

!Various geometry correction functions for the horizontal and vertical axes

5-28	Model 250 Service Manual

Image 83

JVC 250 service manual Convergence Deflection PCB, Horizontal Vertical Deflection PCB - Remove and Replace

Contents

2310 Camino Vida Roble Carlsbad, California SERVICE MANUALModel 250 Projector Phone 760 929-5300 Fax 760DECLARATION OF CONFORMITY Manufacturer Hughes JVCChapter 4 Optical Chapter 1 IntroductionChapter 2 System Description Chapter 3 ElectricalChapter 9 Parts Chapter 7 TroubleshootingChapter 8 Software and Protocol 1.0 Introductio n Contents1.1 Safety 1.3 Acronyms Used 1.2 UpdatesSECAM 2.1 Introduction Contents2.0 System De scription 2.2 Electrical Section Incoming Power CircuitPower Supplies Optical Path Igniter Assembly2.3 Optical Section Arc Lamp ModuleCRTs ILA s - Image Light AmplifierInput Cards VICs 2.4 Electronic SectionRelay Lens Assemblies Front Projection LensPrinted Circuit Boards PCB IR Detectors 2.5 Miscellaneous ItemsCRT/Yoke Assemblies Projector CoversEMI Shield Chapter 2---System Description Model 250 Service ManualContents 3.1 Safety3.0 Electrical AC EMI Filter 3.2. Incoming Power CircuitAC Power Cord AC Circuit BreakerLVPS - Inputs 3.3 Power SuppliesLow Voltage Power Supply LVPS LVPS - Main FunctionsLVPS - Operation 3. Remove the front cover see Projector Covers section Arc Lamp Power Supply ALPSLVPS - Service Adjustments LVPS - Remove and ReplaceALPS - Outputs ALPS - InputsALPS - Operation ALPS - Remove and Replace ALPS - Service AdjustmentsHVPS - Main Functions High Voltage Power Supply HVPS3. Remove the front cover see section 6.1 Projector Covers HVPS - Outputs HVPS - InputsHVPS - Operation HVPS - Service AdjustmentsElectronic Focus Adjustment HVPS - Remove and ReplaceTable 3-1 HVPS - P45 I/O Pinout 10. Disconnect P45 “Control” at upper left of HVPS Igniter Assembly - Operation 3.4 Igniter AssemblyIgniter Assembly - Inputs Igniter Assembly - Outputs3. Remove the front cover see Projector Covers section Igniter Assembly - Service AdjustmentsIgniter Assembly - Remove and Replace 7. Remove the five #1 Pozi-drive Phillips-head screws Contents 4.0 OpticalArc Lamp - Inputs Arc Lamp - Service Adjustments4.1 Arc Lamp Arc Lamp - Main Functions13. Tighten spider lock down bolt Chapter 4---Optical horizontally. Adjust to center the “hot spot”Model 250 Service Manual Figure 4-2 Arc Lamp alignment fixtureArc Lamp - Remove and Replace 8. Disconnect large blower fan connector Optical Path - Main Function 4.2 Optical PathOptical Path - Operation Optical Path - InputsOptical Path - Outputs WARNING!!! Wear safety goggles rated X5 when working anywhere near the light path from the arc lamp or the projection lens 4-10 Model 250 Service ManualFigure 4-6 Optical Path Chapter 4---OpticalFigure 4-7 Optical Path Optical Path - Service AdjustmentsTools Needed 3-mm Hex wrench Parts Needed No serviceable parts Model 250 Service ManualTo adjust the XY Positioner ILA Outputs 4.3 ILAILA Main functions ILA InputsILA Operation ILA Service AdjustmentsILA Overlap 14. Loosen the two hex nuts, using a 4-mm hex-head wrench 19. Retighten the two wing nuts and tighten the two hex nuts NOTE Do not use the zoom lens focus while performing this step ILA Remove and Replace Projection Lens - Input Projection Lens - Service Adjustments4.4 Relay Lenses 4.5 Projection LensFigure 4-11 Projection Lens holding screw and removal notch 3-4-22 Model 100 Service ManualChapter 5 Optical Contents 5.1 Safety5.0 Electronics 5.2 Introduction System Controller PCB - Main Function 5.3 System Controller PCBI/O control for VIC selection Two RS-232 serial interface ports Chapter 5---Electronics Model 250 Service ManualSystem Controller PCB - Inputs System Controller PCB - Outputs System Controller PCB - Operation Figure 5-6 Power On timing sequence Normal Operation Functions System Controller PCB - Remove and Replace Video Processor PCB - Inputs 5.4 Video Processor PCBVideo Processor PCB - Main Functions 5-12 Model 250 Service ManualChapter 5---Electronics Video Processor PCB - Outputs Video Processor PCB - Operation Video Processor PCB - Remove and Replace Raster Timing Generator PCB - Main Functions 5.5 Raster Timing Generator PCBRaster Timing Generator PCB - Inputs Raster Timing Generator PCB - Outputs Raster Timing Generator PCB - Operation Raster Timing Generator PCB - Remove and Replace Horizontal Vertical Deflection PCB - Inputs 5.6 Horizontal Vertical Deflection PCBHorizontal Vertical Deflection PCB - Main Functions IICSINT - IIC interrupt Figure 5-13 Horizontal/Vertical I/O DiagramModel 250 Service Manual IICCLK - IIC clock line IICDATA - IIC data line5-23 Model 250 Service ManualChapter 5---Electronics Vertical Adjustment Pots Horizontal Vertical Deflection PCB - OutputsHorizontal Vertical Deflection PCB - Operation Horizontal Vertical Deflection PCB - Service Adjustments Figure 5-17 Red image needs vertical adjustment increase Convergence Deflection PCB - Main Functions 5.7 Convergence Deflection PCBHorizontal Vertical Deflection PCB - Remove and Replace Convergence Deflection PCB - Outputs Convergence Deflection PCB - Inputs5-30 Figure 5-19 Convergence Deflection PCB I/O DiagramModel 250 Service Manual Chapter 5---Electronics5-31 Figure 5-20 Convergence Deflection PCB I/O DiagramModel 250 Service Manual Chapter 5---ElectronicsConvergence Deflection PCB - Operation Convergence Deflection PCB - Remove and Replace Scan Reversal PCB - Inputs 5.8 Scan Reversal PCBScan Reversal PCB - Main Functions Scan Reversal PCB - Outputs 5-36 Figure 5-22 Scan Reversal PCB I/O DiagramModel 250 Service Manual Chapter 5---Electronics5-37 Model 250 Service ManualChapter 5---Electronics Scan Reversal PCB - Operation front/upright projection. This means the horizontal scan jumper is plugged into J100, the vertical scan jumper is plugged into J53, and the convergence jumper is plugged into J50 Scan Reversal PCB - Service Adjustments Page Vertical CAUTION! The Model 250 Projector can not beOrientation ConvergenceVideo Amplifier PCB - Main Functions 5.9 Video Amplifier PCBScan Reversal PCB - Remove and Replace Video Amplifier PCB - Inputs 5-45 Figure 5-26 Video Amplifier PCB I/O DiagramModel 250 Service Manual Chapter 5---ElectronicsVideo Amplifier PCB - Outputs Video Amplifier PCB - Operation Video Amplifier PCB - Remove and Replace Page 15. Reinstall in the reverse order from above CRT/Yoke Assemblies - Output 5.10 CRT/Yoke AssembliesCRT/Yoke Assemblies - Main Function CRT/Yoke Assemblies - InputsCRT/Yoke Assemblies - Operation CRT/Yoke Assemblies - Service AdjustmentsCRT Mechanical Focus Figure 5-29 CRT Mechanical Focus adjustments CRT Rotation 12. In the Geometry menu, put a check the Reg Enable box CRT Electronic Focus CRT/Yoke Assemblies - Remove and Replace CAUTION! Use extreme caution to avoid bumping 5.11 Video Input Cards VICsRGBHV VIC - Main Functions Standard RGBHV VICRGBHV VIC - Operation RGBHV VIC - Service AdjustmentsRGBHV VIC - Inputs RGBHV VIC - OutputsGrahics Enhancer Plus RGBHV VIC - Main Functions Graphics Enhancer Plus RGBHV VICGraphics Enhancer Plus VIC - Outputs Graphics Enhancer Plus VIC - InputsGraphics Enhancer Plus VIC - Remove and Replace Graphics Enhancer Plus VIC - Service AdjustmentsGraphics Enhancer Plus VIC - Operation 4-Input Quad RGBHV VIC - Inputs 4-Input Quad RGBHV VIC4-Input Quad RGBHV VIC - Main Functions Chapter 5---Electronics Model 250 Service ManualIIC CLK - IIC clock line IIC DATA - IIC data line IIC SINT - IIC interrupt line Figure 5-36 4-Input Quad RGBHV VIC4-Input Quad RGBHV VIC - Remove and Replace 4-Input Quad RGBHV VIC - Service Adjustments4-Input Quad RGBHV VIC - Outputs 4-Input Quad RGBHV VIC - OperationYPbPr VIC - Main Functions YPbPr VICYPbPr VIC - Operation YPbPr VIC - InputsYPbPr VIC - Outputs YPbPr VIC - Remove and Replace YPbPr VIC - Service AdjustmentsQuad Standard Decoder VIC - Main Functions Quad Standard Decoder VICQuad Standard Decoder VIC - Operation Quad Standard Decoder VIC - InputsQuad Standard Decoder VIC - Outputs Quad Standard Decoder VIC - Remove and Replace Quad Standard Decoder VIC - Service AdjustmentsQuad Standard Decoder/Line Doubler VIC installed in the #2 or 3 VIC slot it will not fit into the #1 slot, a blank face plate must be installed above it. The blank faceplate is not included with the Quad Standard Decoder/Line Doubler VIC unless it is installed at the factory. The part number for the blank faceplate is p/n 5.12 Backplane PCB see Figure Figure 5-43 Backplane Diagram middle section5-76 Figure 5-44 Backplane Diagram right sideModel 250 Service Manual Chapter 5---Electronics5-77 Model 250 Service ManualChapter 5---Electronics Contents 6.0 Miscellaneous Items6.1 Projector Covers 6.2 Electronics Module Tilt-up 6.3 Ventilation 6.6 EMI Filter 6.4 Air Filters6.5 IR Detectors 6.7 Cleaning Lenses, ILA Assemblies and Mirrors Chapter 6---Miscellaneous Items Model 250 Service ManualContents 7.0 Troubleshooting7.1 Safety Backpanel LEDs 7.2 LEDsFigure 7-1 Rear Panel layout Figure 7-2 Dip Switch Block on System Controller PCB Model 250 Service Manual Video Processor PCB LEDsVideo Processor - Test Points Chapter 7---TroubleshootingVideo Processor - LEDs Figure 7-6 Raster Timing Generator LEDs Raster Timing Generator PCB LEDsChapter 7---Troubleshooting Model 250 Service ManualRaster Timing Generator PCB LEDs Figure 7-7 Convergence Deflection PCB LED Convergence Deflection PCB LEDChapter 7---Troubleshooting Model 250 Service ManualVideo Amplifier PCB LED Backplane PCB LEDs Command ON Timing 7.3 Diagramsto the Arc Lamp Power Supply low. The Arc Lamp Power Supply delivers 170 V to the Igniter, which generates a 32 kV pulse to the Arc Lamp and the Arc Lamp lights. Once the Arc Lamp lights, the Arc Lamp Power Supply, the /LAMPLIT signal goes low and the voltage to the Igniter drops to between 25 V and 31 V. The voltage from the Arc Lamp Power Supply stays at a steady output of 2 kW during normal operation of the projector Image Path Deflection Path The Horizontal Vertical Deflection PCB outputs HOUTFLYBACK to the Scan Reversal PCB. This is the horizontal deflection waveform that drives the horizontal CRT deflection yokes. The HRED+, GRN+, and BLU+ are the horizontal deflection returns. The outputs of the vertical amplifier are VRED+, GRN+, and BLU+. The returns are VRED-, GRN-, and BLU Convergence Deflection PCB and Scan Reversal PCB Chapter 7---TroubleshootingModel 250 Service Manual Figure 7-13 CRT Deflection path between Horiz/Vert Deflection PCB7-18 Chapter 7---TroubleshootingModel 250 Service Manual Figure 7-14 CRT Deflection path between the Scan Reversal PCB and CRTCRT Protection Yoke Connector Detection 7-21 Chapter 7---TroubleshootingModel 250 Service Manual Figure 7-16 CRT Protection path between the Scan Reversal PCB and CRT7.4 Error Codes “No mem available” 4.17 “VIC1 Board Not OK” /VICOK is High BAD on VIC Slot Check 7.5 Troubleshooting GuideProblem Possible SolutionModel 250 Service Manual Troubleshooting on the Backplane PCBFigure 7-17 Backplane Diagram left side Chapter 7---TroubleshootingLow Voltage Power Supply J8 7-28 Figure 7-19 Backplane Diagram right sideChapter 7---Troubleshooting Model 250 Service Manual7-29 Chapter 7---TroubleshootingModel 250 Service Manual Contents 8.0 Software and Protocol8.1 Software Updating Cursor=Block & Blink Terminal Font=Fixedsys Translation=None 11B. From the Windows Terminal Menu normally in Accessories window, select Transfers/Send Text File, then select List Files of Type All Files, and select the disk and/or directory with the Model 250 software. You should see a file named boot.hex. Select this file and press the OK button to begin the upload. Uploading takes about 20 minutes 9600 bps 12A. To update the System Software from the Boot Manager prompt 8.2 Importing/Exporting ConfigurationStop, Pause, Bytes 0, Receiving EXPORT1.TXT Exporting4. Windows TERMINAL Transfers + Receive Text File Importing Stop, Pause, “% complete bar”, Sending EXPORT1.TXT Null Modem Adapter Terminal Preferences 8.3 Terminals and Communication ProtocolsTerminals Action Table 8-3 VT-100 Terminal and Remote Command EquivalentsService Communications ProtocolCenter, H Refer to Section 8.1, Software Updating 8-14 Model 250 Service ManualChapter 8---Software and Protocol Contents 9.0 Parts List9.1 Replacement Parts List DescriptionDescription Power Cord, USA/JapanDescription 9.2 SparesQuantity Model 250 Service Manual Chapter 9---Parts ListArc Lamp Cross-member AssemblyGlossary of Terms AmorphousHorizontal Scan Laser Power SupplyField FrameNoise ResolutionLumen LuminanceScan Vertical ResolutionS-Video Saturated ColorFrequency Vertical Scan FrequencyVertical Scan Vertical Synchronization