Change Software, Change Speed | Lantronix MSS guide

Command Reference	Change Software
Examples	CHANGE SNMPSETCOMM WPHRED
	(adds a single community with read-write access)
See Also	The Configuration chapter of your Installation Guide

2.57 Change Software

CHANGE SERVER SOFTWARE filename

Specifies the name of the download file that, when a reload has been requested, the MSS will attempt to load at boot time.

Restrictions

Requires privileged user status.

ParametersServer

MSS4 only.

filename

Specify a loadfile name of 11 or fewer characters. The server will automatically add a .SYS extension to the file name. You can also enter the complete pathname if the file is to be loaded via TFTP; place the filename in quotes to preserve case.

See Also

Change Loadhost, page 2-29.

2.58 Change Speed

CHANGE PORT PortList SPEED rate

Specifies the baud rate of the serial port.

Restrictions	Requires privileged user status.
Errors	An error is displayed if an unsupported baud rate is specified.
Parameters	Port
	MSS4 only. Specifies a particular port or group of ports.
Note:	In the absence of the PortList parameter, the configuration will affect the MSS4’s
	current port only.
	PortList
	Specify a particular port or group of ports. Port numbers are specified with
	integers between 1 and 4, and should be separated with commas (for lists) or
	dashes (for ranges).

2-45

Image 54

Lantronix MSS manual Change Software, Change Speed

Contents

MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s New Command Line Editing Key Purpose Help About This Manual Command Reference Change 80211 Enabled BackwardChange Defaults Change 80211 Antenna Restrictions Change 80211 MAC Address ErrorsChange 80211 Fragmentation Parameters Change 80211 Network Mode Examples Change 80211 Power Change 80211 Region Change 80211 Reset Change 80211 RTS Change 80211 WEP Change Access Current port only DefaultsDynamic See Also Change Autobaud Change Autostart Dashes for ranges Change Backward Switch Change Bootgateway Change Break Change BootpDefaultsEnabled Restrictions Requires privileged user status ParametersPort Change Buffering DefaultsNone See AlsoDefaults Bytes Change Charsize Change Datasend Condition has been detected Change Dedicated Restrictions Command on Change Dhcp Change Domain Change DSRLogout Change DTRWait DefaultsDisabled Change Flow Control Change Forward Switch Change Gateway Change Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPAddress Change IPSecurity Change LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Loginpass Change Modem Control Change Modem Emulation Change Name Change Nameserver Change NetWare Encapsulation Change NetWare Internal Network Change NetWare Loadhost Change NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Incoming Change Password Limit Change Password Protect Change Portname Change Preferred Change Privpass Change Rarp Change Rlogin Change Retransmit Limit Change RS485 Change Signal Check Change SecondaryChange Session Limit Change Silentboot Change SNMPSetComm Change Software Change Speed Change Startup Two colons and the startup file name of up to 47 characters Defaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Change Timeserver Daytime is only supported over UDP Change Verify Change Wins Crypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Finger Delete IPSecurityDisconnect Parametersusername Forward HostlistParameterskeyword Show Hostlist command Initialize 78 LAT ParametersDelayParametersserviceName Logout Port Resume NetstatPing Parametershostname Rlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show NetWare Show HostlistShow IPsecurity Show Nodes Show Server Show PortsShow RS485 ParametersAll Show Services ParametersBootparamsShow Session Show Version Show SnmpShow Users Source 100 SPX TelnetParametersSAPname Test Zero Problem Report Procedure Full Contact Information Usage Available StringsMultiple Strings Usage Examples Xxxx 1.5 or ParametersS 1.11 Y Error Bits IntroductionLeftmost Number 04000000 1000000008000000 02000000 Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWare Telnet 2-48,2-68 UDP 2-50,B-3