Delete IPSecurity, Disconnect, Finger | Lantronix MSS instruction

Command Reference

Delete IPSecurity

2.71 Delete IPSecurity

	IPaddress 
DELETE IPSECURITY 	
	ALL 

Removes entries from the IP Security table.

Restrictions	Requires privileged user status.
Errors	An error will be returned if the IPSecurity entry does not exist.
See Also	Change IPSecurity, page 2-27; Show IPsecurity, page 2-64.

2.72 Disconnect

DISCONNECT session

Terminates the current session or specified session(s).

2.73 Finger

FINGER

username @ hostname

Displays information about local and remote users. This command is an implementation of the Unix Finger command. Port information will not be displayed.

Restrictions

An error is returned when the host cannot be accessed.

Parametersusername

Enter a username to display information about that particular MSS user.

hostname

Enter a hostname to display information about all of the users at the specified host site.

username@hostname

Enter both parameters with the “at” symbol (@) to display information about a particular user on that host.

2-57

Image 66

Lantronix MSS manual Delete IPSecurity, Disconnect, Finger, Parametersusername

Contents

MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s New Command Line Editing Key Purpose Help About This Manual Command Reference Change 80211 Enabled BackwardChange Defaults Change 80211 Antenna Restrictions Change 80211 MAC Address ErrorsChange 80211 Fragmentation Parameters Change 80211 Network Mode Examples Change 80211 Power Change 80211 Region Change 80211 Reset Change 80211 RTS Change 80211 WEP Change Access Current port only DefaultsDynamic See Also Change Autobaud Change Autostart Dashes for ranges Change Backward Switch Change Bootgateway Change Break Change BootpDefaultsEnabled Restrictions Requires privileged user status ParametersPort Change Buffering DefaultsNone See AlsoDefaults Bytes Change Charsize Change Datasend Condition has been detected Change Dedicated Restrictions Command on Change Dhcp Change Domain Change DSRLogout Change DTRWait DefaultsDisabled Change Flow Control Change Forward Switch Change Gateway Change Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPAddress Change IPSecurity Change LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Loginpass Change Modem Control Change Modem Emulation Change Name Change Nameserver Change NetWare Encapsulation Change NetWare Internal Network Change NetWare Loadhost Change NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Incoming Change Password Limit Change Password Protect Change Portname Change Preferred Change Privpass Change Rarp Change Rlogin Change Retransmit Limit Change RS485 Change Signal Check Change SecondaryChange Session Limit Change Silentboot Change SNMPSetComm Change Software Change Speed Change Startup Two colons and the startup file name of up to 47 characters Defaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Change Timeserver Daytime is only supported over UDP Change Verify Change Wins Crypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Finger Delete IPSecurityDisconnect Parametersusername Forward HostlistParameterskeyword Show Hostlist command Initialize 78 LAT ParametersDelayParametersserviceName Logout Port Resume NetstatPing Parametershostname Rlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show NetWare Show HostlistShow IPsecurity Show Nodes Show Server Show PortsShow RS485 ParametersAll Show Services ParametersBootparamsShow Session Show Version Show SnmpShow Users Source 100 SPX TelnetParametersSAPname Test Zero Problem Report Procedure Full Contact Information Usage Available StringsMultiple Strings Usage Examples Xxxx 1.5 or ParametersS 1.11 Y Error Bits IntroductionLeftmost Number 04000000 1000000008000000 02000000 Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWare Telnet 2-48,2-68 UDP 2-50,B-3