Change Passflow, DefaultsNone See Also | Lantronix MSS manual

Command Reference

Change Passflow

Parameters

Note:

Port

MSS4 only. Specifies a particular port or group of ports.

In the absence of the PortList parameter, the configuration will affect the MSS4’s current port only.

PortList

Specify a particular port or group of ports. Port numbers are specified with integers between 1 and 4, and should be separated with commas (for lists) or dashes (for ranges).

DefaultsNone

See Also

Change Autobaud, page 2-11; Change Charsize, page 2-16.

2.41 Change Passflow

 DISABLED 

CHANGE PORT PortList PASSFLOW   ENABLED 

Specifies whether XON/XOFF characters will be stripped from the data stream. Enabled means that the MSS will both respond to XON/XOFF and send them to the host. Disabled means that we respond to XON/ XOFF but do not send them to the host. Passflow is only useful when XonXoff flow control is set.

Parameters

Note:

Port

MSS4 only. Specifies a particular port or group of ports.

In the absence of the PortList parameter, the configuration will affect the MSS4’s current port only.

PortList

Specify a particular port or group of ports. Port numbers are specified with integers between 1 and 4, and should be separated with commas (for lists) or dashes (for ranges).

See Also

Change Flow Control, page 2-23.

2-36

Image 45

Lantronix MSS manual Change Passflow, DefaultsNone See Also

Contents

MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command Syntax Key Purpose Command Line Editing About This Manual Help Command Reference Change 80211 Enabled BackwardChange Change 80211 Antenna Defaults Restrictions Change 80211 Fragmentation ErrorsChange 80211 MAC Address Parameters Examples Change 80211 Network Mode Change 80211 Region Change 80211 Power Change 80211 RTS Change 80211 Reset Change 80211 WEP Current port only Change Access Change Autobaud DefaultsDynamic See Also Change Autostart Dashes for ranges Change Bootgateway Change Backward Switch DefaultsEnabled Change BootpChange Break Restrictions Requires privileged user status ParametersPort Defaults Bytes DefaultsNone See AlsoChange Buffering Change Charsize Change Datasend Condition has been detected Restrictions Change Dedicated Command on Change Domain Change Dhcp Change DTRWait Change DSRLogout Change Flow Control DefaultsDisabled Change Gateway Change Forward Switch Change Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPSecurity Change IPAddress Change LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Modem Control Change Loginpass Change Name Change Modem Emulation Change NetWare Encapsulation Change Nameserver Change NetWare Loadhost Change NetWare Internal Network Change NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Limit Change Password Incoming Change Portname Change Password Protect Change Preferred Change Rarp Change Privpass Change Retransmit Limit Change Rlogin Change RS485 Change Signal Check Change SecondaryChange Session Limit Change SNMPSetComm Change Silentboot Change Speed Change Software Two colons and the startup file name of up to 47 characters Change Startup Defaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Daytime is only supported over UDP Change Timeserver Change Wins Change Verify Crypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Disconnect Delete IPSecurityFinger Parametersusername Forward HostlistParameterskeyword Initialize Show Hostlist command ParametersserviceName ParametersDelay78 LAT Logout Port Ping NetstatResume Parametershostname Rlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show IPsecurity Show HostlistShow NetWare Show Nodes Show RS485 Show PortsShow Server ParametersAll Show Services ParametersBootparamsShow Session Show Users Show SnmpShow Version Source 100 SPX TelnetParametersSAPname Zero Test Full Contact Information Problem Report Procedure Usage Available StringsMultiple Strings Xxxx Usage Examples ParametersS 1.5 or 1.11 Y Error Bits IntroductionLeftmost Number 08000000 1000000004000000 02000000 Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37 UDP 2-50,B-3 Telnet 2-48,2-68