Change Verify, Change Wins | Lantronix MSS manual

Command Reference

Change Verify

2.67 Change Verify

 DISABLED 

CHANGE PORT PortList VERIFY   ENABLED 

Controls whether the MSS will provide informational messages whenever a session is connected, disconnected, or switched.

Restrictions	Requires privileged user status.
	If a port is Dedicated, Verify is disabled.

Parameters

Note:

Port

MSS4 only. Specifies a particular port or group of ports.

In the absence of the PortList parameter, the configuration will affect the MSS4’s current port only.

PortList

Specify a particular port or group of ports. Port numbers are specified with integers between 1 and 4, and should be separated with commas (for lists) or dashes (for ranges).

DefaultsEnabled

2.68 Change WINS

 DISABLED 

CHANGE SERVER WINS   ENABLED 

Allows the MSS to broadcast a WINS name announcement at boot time, and answer broadcast WINS name queries. This setting allows other hosts to locate the MSS.

Restrictions

Requires privileged user status.

ParametersServer

MSS4 only.

DefaultsDisabled

2-51

Image 60

Lantronix MSS manual Change Verify, Change Wins

Contents

MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s New Command Line Editing Key Purpose Help About This Manual Command Reference Change 80211 Enabled BackwardChange Defaults Change 80211 Antenna Restrictions Errors Change 80211 FragmentationChange 80211 MAC Address Parameters Change 80211 Network Mode Examples Change 80211 Power Change 80211 Region Change 80211 Reset Change 80211 RTS Change 80211 WEP Change Access Current port only DefaultsDynamic See Also Change Autobaud Change Autostart Dashes for ranges Change Backward Switch Change Bootgateway Change Bootp DefaultsEnabledChange Break Restrictions Requires privileged user status ParametersPort DefaultsNone See Also Defaults BytesChange Buffering Change Charsize Change Datasend Condition has been detected Change Dedicated Restrictions Command on Change Dhcp Change Domain Change DSRLogout Change DTRWait DefaultsDisabled Change Flow Control Change Forward Switch Change Gateway Change Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPAddress Change IPSecurity Change LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Loginpass Change Modem Control Change Modem Emulation Change Name Change Nameserver Change NetWare Encapsulation Change NetWare Internal Network Change NetWare Loadhost Change NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Incoming Change Password Limit Change Password Protect Change Portname Change Preferred Change Privpass Change Rarp Change Rlogin Change Retransmit Limit Change RS485 Change Signal Check Change SecondaryChange Session Limit Change Silentboot Change SNMPSetComm Change Software Change Speed Change Startup Two colons and the startup file name of up to 47 characters Defaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Change Timeserver Daytime is only supported over UDP Change Verify Change Wins Crypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Delete IPSecurity DisconnectFinger Parametersusername Forward HostlistParameterskeyword Show Hostlist command Initialize ParametersDelay ParametersserviceName78 LAT Logout Port Netstat PingResume Parametershostname Rlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show Hostlist Show IPsecurityShow NetWare Show Nodes Show Ports Show RS485Show Server ParametersAll Show Services ParametersBootparamsShow Session Show Snmp Show UsersShow Version Source 100 SPX TelnetParametersSAPname Test Zero Problem Report Procedure Full Contact Information Usage Available StringsMultiple Strings Usage Examples Xxxx 1.5 or ParametersS 1.11 Y Error Bits IntroductionLeftmost Number 10000000 0800000004000000 02000000 Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWare Telnet 2-48,2-68 UDP 2-50,B-3