Show Services, Show Session, ParametersBootparams | Lantronix MSS

Command Reference

Show Services

ParametersBootparams

Displays MSS parameters that relate to the boot procedure and software loadfile.

Counters

Displays Ethernet and TCP/IP error information.

Characteristics

Displays server settings including hardware address, timer limit, password limit, session limit, retransmit limit, IP address, subnet mask, nameserver, gateway, and more.

DefaultsCharacteristics

See Also

Status Displays, page 5-6.

2.94 Show Services

SHOW SERVICES [ serviceName]

Displays the characteristics of the LAT services on the network.

Restrictions	This list is masked by the service groups that the port is able to see. In other
	words, users will not be able to see services to which they cannot connect.
Errors	Does not apply to MSSLite, MSS-VIA, or the MSS4.
Parameters	serviceName
	Specify a service whose information you want to see. Wildcards are permitted.
	All services will be shown if no service is specified.
See Also	Status Displays, page 5-6.

2.95 Show Session

SHOW SESSION

Displays information about the serial port’s current session(s). For the MSS4, this command shows the current session(s) for the current serial port.

See Also

Status Displays, page 5-6.

2-66

Image 75

Lantronix MSS manual Show Services, Show Session, ParametersBootparams

Contents

MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command Syntax Key Purpose Command Line Editing About This Manual Help Command Reference Change 80211 Enabled BackwardChange Change 80211 Antenna Defaults Restrictions Parameters ErrorsChange 80211 Fragmentation Change 80211 MAC Address Examples Change 80211 Network Mode Change 80211 Region Change 80211 Power Change 80211 RTS Change 80211 Reset Change 80211 WEP Current port only Change Access Change Autobaud DefaultsDynamic See Also Change Autostart Dashes for ranges Change Bootgateway Change Backward Switch Restrictions Requires privileged user status ParametersPort Change BootpDefaultsEnabled Change Break Change Charsize DefaultsNone See AlsoDefaults Bytes Change Buffering Change Datasend Condition has been detected Restrictions Change Dedicated Command on Change Domain Change Dhcp Change DTRWait Change DSRLogout Change Flow Control DefaultsDisabled Change Gateway Change Forward Switch Change Inactive Timer DefaultsDisabled See AlsoChange Inactive Logout Change Incoming Change IPSecurity Change IPAddress Change LAT CircTimer Change LAT Groups Change LAT IdentificationChange Loadhost Change Local Switch Change Modem Control Change Loginpass Change Name Change Modem Emulation Change NetWare Encapsulation Change Nameserver Change NetWare Loadhost Change NetWare Internal Network Change NetWare Routing Change ParityParametersfileserver Change Passflow Change Password Limit Change Password Incoming Change Portname Change Password Protect Change Preferred Change Rarp Change Privpass Change Retransmit Limit Change Rlogin Change RS485 Change Signal Check Change SecondaryChange Session Limit Change SNMPSetComm Change Silentboot Change Speed Change Software Two colons and the startup file name of up to 47 characters Change Startup Defaults See Also Change StopbitsChange Subnet Mask DefaultsConsole Change TCPKeepaliveChange Telnetdest Change Telnetpad Change TermtypeParameters Examples Daytime is only supported over UDP Change Timeserver Change Wins Change Verify Crypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Parametersusername Delete IPSecurityDisconnect Finger Forward HostlistParameterskeyword Initialize Show Hostlist command Logout Port ParametersDelayParametersserviceName 78 LAT Parametershostname NetstatPing Resume Rlogin 84 RTCParametersIPaddress Set Privileged ShowParametersAntenna Show Nodes Show HostlistShow IPsecurity Show NetWare ParametersAll Show PortsShow RS485 Show Server Show Services ParametersBootparamsShow Session Source Show SnmpShow Users Show Version 100 SPX TelnetParametersSAPname Zero Test Full Contact Information Problem Report Procedure Usage Available StringsMultiple Strings Xxxx Usage Examples ParametersS 1.5 or 1.11 Y Error Bits IntroductionLeftmost Number 02000000 1000000008000000 04000000 Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37 UDP 2-50,B-3 Telnet 2-48,2-68