Show Ports, Show RS485, Show Server, ParametersAll | Lantronix MSS

Command Reference

Show Ports

SPX

Shows SPX node hop counts, frame types, and availability.

See Also

Status Displays, page 5-6.

2.91 Show Ports

SHOW PORTS

ALL

PortList

Displays all serial port settings, including the port’s connection status, the flow control state , the state of DSR and DTR serial signals, the access type, and more. Can also be used to display modem card information (for the MSS-Via, Port 3; for the MSS4, Ports 5 and 6).

ParametersAll

MSS4 only. Shows the port settings on all serial ports.

PortList

MSS4 and MSSVia only. Port numbers are specified with integers between 1 and 4. Port numbers should be separated with commas (for lists) or dashes (for ranges).

See Also

Status Displays, page 5-6.

2.92 Show RS485

SHOW RS485

Displays the current RS-485 networking settings, including wire mode, termination, and TXDrive.

Errors	Only applies to the MSS-VIA and MSS4.
See Also	Change RS485, page 2-42.

2.93 Show Server

SHOW SERVER

BOOTPARAMS

COUNTERS

CHARACTERISTICS

Displays different types of MSS information. If you do not enter a parameter, the MSS will display general server characteristics .

2-65

Image 74

Lantronix MSS manual Show Ports, Show RS485, Show Server, ParametersAll

Contents

MSS Reference Manual Part Number Contents Contents Iii Index Command Syntax What’s New Command Line Editing Key Purpose Help About This Manual Command Reference Change Change 80211 EnabledBackward Defaults Change 80211 Antenna Restrictions Change 80211 MAC Address ErrorsChange 80211 Fragmentation Parameters Change 80211 Network Mode Examples Change 80211 Power Change 80211 Region Change 80211 Reset Change 80211 RTS Change 80211 WEP Change Access Current port only DefaultsDynamic See Also Change Autobaud Change Autostart Dashes for ranges Change Backward Switch Change Bootgateway Change Break Change BootpDefaultsEnabled Restrictions Requires privileged user status ParametersPort Change Buffering DefaultsNone See AlsoDefaults Bytes Change Charsize Change Datasend Condition has been detected Change Dedicated Restrictions Command on Change Dhcp Change Domain Change DSRLogout Change DTRWait DefaultsDisabled Change Flow Control Change Forward Switch Change Gateway Change Inactive Logout Change Inactive TimerDefaultsDisabled See Also Change Incoming Change IPAddress Change IPSecurity Change LAT CircTimer Change Loadhost Change LAT GroupsChange LAT Identification Change Local Switch Change Loginpass Change Modem Control Change Modem Emulation Change Name Change Nameserver Change NetWare Encapsulation Change NetWare Internal Network Change NetWare Loadhost Parametersfileserver Change NetWare RoutingChange Parity Change Passflow Change Password Incoming Change Password Limit Change Password Protect Change Portname Change Preferred Change Privpass Change Rarp Change Rlogin Change Retransmit Limit Change RS485 Change Session Limit Change Signal CheckChange Secondary Change Silentboot Change SNMPSetComm Change Software Change Speed Change Startup Two colons and the startup file name of up to 47 characters Change Subnet Mask Defaults See AlsoChange Stopbits Change Telnetdest DefaultsConsoleChange TCPKeepalive Parameters Examples Change TelnetpadChange Termtype Change Timeserver Daytime is only supported over UDP Change Verify Change Wins Crypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Finger Delete IPSecurityDisconnect Parametersusername Parameterskeyword ForwardHostlist Show Hostlist command Initialize 78 LAT ParametersDelayParametersserviceName Logout Port Resume NetstatPing Parametershostname ParametersIPaddress Rlogin84 RTC ParametersAntenna Set PrivilegedShow Show NetWare Show HostlistShow IPsecurity Show Nodes Show Server Show PortsShow RS485 ParametersAll Show Session Show ServicesParametersBootparams Show Version Show SnmpShow Users Source ParametersSAPname 100 SPXTelnet Test Zero Problem Report Procedure Full Contact Information Multiple Strings UsageAvailable Strings Usage Examples Xxxx 1.5 or ParametersS 1.11 Y Leftmost Number Error BitsIntroduction 04000000 1000000008000000 02000000 Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Login 2-31,2-37 Security 2-27,2-57,2-64IPX NetWare Telnet 2-48,2-68 UDP 2-50,B-3