Change Password Protect, Change Portname | Lantronix MSS specification

Command Reference

Change Password Protect

2.44 Change Password Protect

 DISABLED 

CHANGE PORT PortList PASSWORD PROTECT   ENABLED 

Controls whether a password is needed to log into the MSS from a serial port. For models with a dedicated console port (the MSS-Via, MSS485, and the MSSLite A and C), this command will also affect the serial console port. To set the login password, use the Change Loginpass command.

Restrictions

Requires privileged user status.

ParametersPort

MSS4 only. Specifies a particular port or group of ports.

Note: In the absence of the PortList parameter, the configuration will affect the MSS4’s current port only.

PortList

Specify a particular port or group of ports. Port numbers are specified with integers between 1 and 4, and should be separated with commas (for lists) or dashes (for ranges).

DefaultsDisabled

See Also

Change Loginpass, page 2-31.

2.45 Change Portname

CHANGE PORT PortList PORTNAME name

Renames the specified serial port.

Restrictions	Requires privileged user status.
Parameters	Port
	MSS4 only. Specifies a particular port or group of ports.
Note:	In the absence of the PortList parameter, the configuration will affect the MSS4’s
	current port only.
	PortList
	Specify a particular port or group of ports. Port numbers are specified with
	integers between 1 and 4, and should be separated with commas (for lists) or
	dashes (for ranges).
	name
	Enter a 16-character name composed of alphanumeric characters or the
	underscore character. Enclose the name in quotation marks to preserve case.
Defaults	Port_1 (also Port_2, Port_3, and Port_4 for MSS4 only)
	2-38

Image 47

Lantronix MSS manual Change Password Protect, Change Portname

Contents

MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command Syntax Key Purpose Command Line Editing About This Manual Help Command Reference Change Change 80211 EnabledBackward Change 80211 Antenna Defaults Restrictions Parameters ErrorsChange 80211 Fragmentation Change 80211 MAC Address Examples Change 80211 Network Mode Change 80211 Region Change 80211 Power Change 80211 RTS Change 80211 Reset Change 80211 WEP Current port only Change Access Change Autobaud DefaultsDynamic See Also Change Autostart Dashes for ranges Change Bootgateway Change Backward Switch Restrictions Requires privileged user status ParametersPort Change BootpDefaultsEnabled Change Break Change Charsize DefaultsNone See AlsoDefaults Bytes Change Buffering Change Datasend Condition has been detected Restrictions Change Dedicated Command on Change Domain Change Dhcp Change DTRWait Change DSRLogout Change Flow Control DefaultsDisabled Change Gateway Change Forward Switch Change Inactive Logout Change Inactive TimerDefaultsDisabled See Also Change Incoming Change IPSecurity Change IPAddress Change LAT CircTimer Change Loadhost Change LAT GroupsChange LAT Identification Change Local Switch Change Modem Control Change Loginpass Change Name Change Modem Emulation Change NetWare Encapsulation Change Nameserver Change NetWare Loadhost Change NetWare Internal Network Parametersfileserver Change NetWare RoutingChange Parity Change Passflow Change Password Limit Change Password Incoming Change Portname Change Password Protect Change Preferred Change Rarp Change Privpass Change Retransmit Limit Change Rlogin Change RS485 Change Session Limit Change Signal CheckChange Secondary Change SNMPSetComm Change Silentboot Change Speed Change Software Two colons and the startup file name of up to 47 characters Change Startup Change Subnet Mask Defaults See AlsoChange Stopbits Change Telnetdest DefaultsConsoleChange TCPKeepalive Parameters Examples Change TelnetpadChange Termtype Daytime is only supported over UDP Change Timeserver Change Wins Change Verify Crypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Parametersusername Delete IPSecurityDisconnect Finger Parameterskeyword ForwardHostlist Initialize Show Hostlist command Logout Port ParametersDelayParametersserviceName 78 LAT Parametershostname NetstatPing Resume ParametersIPaddress Rlogin84 RTC ParametersAntenna Set PrivilegedShow Show Nodes Show HostlistShow IPsecurity Show NetWare ParametersAll Show PortsShow RS485 Show Server Show Session Show ServicesParametersBootparams Source Show SnmpShow Users Show Version ParametersSAPname 100 SPXTelnet Zero Test Full Contact Information Problem Report Procedure Multiple Strings UsageAvailable Strings Xxxx Usage Examples ParametersS 1.5 or 1.11 Y Leftmost Number Error BitsIntroduction 02000000 1000000008000000 04000000 Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37 UDP 2-50,B-3 Telnet 2-48,2-68