Telnet 2-48,2-68, UDP 2-50,B-3 | Lantronix MSS instruction

Index

T

Telnet 2-48,2-68

Padding characters 2-48,2-49

Raw connections B-3

Terminal type 2-49

Test command 2-69

Timers

Circuit 2-28

Inactivity 2-25

Timeserver 2-50

U

UDP 2-50,B-3

Passive B-3

Unix commands 2-53

Users 2-67

V

Verification 2-51

W

WEP (Wireless Equivalent Privacy) 2-9

WINS 2-51

Wireless 2-2,2-63

Z

Zeroing counters 2-69

Index-3

Image 91

Lantronix MSS manual Telnet 2-48,2-68, UDP 2-50,B-3

Contents

MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command Syntax Key Purpose Command Line Editing About This Manual Help Command Reference Backward Change 80211 EnabledChange Change 80211 Antenna Defaults Restrictions Parameters ErrorsChange 80211 Fragmentation Change 80211 MAC Address Examples Change 80211 Network Mode Change 80211 Region Change 80211 Power Change 80211 RTS Change 80211 Reset Change 80211 WEP Current port only Change Access Change Autobaud DefaultsDynamic See Also Change Autostart Dashes for ranges Change Bootgateway Change Backward Switch Restrictions Requires privileged user status ParametersPort Change BootpDefaultsEnabled Change Break Change Charsize DefaultsNone See AlsoDefaults Bytes Change Buffering Change Datasend Condition has been detected Restrictions Change Dedicated Command on Change Domain Change Dhcp Change DTRWait Change DSRLogout Change Flow Control DefaultsDisabled Change Gateway Change Forward Switch DefaultsDisabled See Also Change Inactive TimerChange Inactive Logout Change Incoming Change IPSecurity Change IPAddress Change LAT CircTimer Change LAT Identification Change LAT GroupsChange Loadhost Change Local Switch Change Modem Control Change Loginpass Change Name Change Modem Emulation Change NetWare Encapsulation Change Nameserver Change NetWare Loadhost Change NetWare Internal Network Change Parity Change NetWare RoutingParametersfileserver Change Passflow Change Password Limit Change Password Incoming Change Portname Change Password Protect Change Preferred Change Rarp Change Privpass Change Retransmit Limit Change Rlogin Change RS485 Change Secondary Change Signal CheckChange Session Limit Change SNMPSetComm Change Silentboot Change Speed Change Software Two colons and the startup file name of up to 47 characters Change Startup Change Stopbits Defaults See AlsoChange Subnet Mask Change TCPKeepalive DefaultsConsoleChange Telnetdest Change Termtype Change TelnetpadParameters Examples Daytime is only supported over UDP Change Timeserver Change Wins Change Verify Crypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Parametersusername Delete IPSecurityDisconnect Finger Hostlist ForwardParameterskeyword Initialize Show Hostlist command Logout Port ParametersDelayParametersserviceName 78 LAT Parametershostname NetstatPing Resume 84 RTC RloginParametersIPaddress Show Set PrivilegedParametersAntenna Show Nodes Show HostlistShow IPsecurity Show NetWare ParametersAll Show PortsShow RS485 Show Server ParametersBootparams Show ServicesShow Session Source Show SnmpShow Users Show Version Telnet 100 SPXParametersSAPname Zero Test Full Contact Information Problem Report Procedure Available Strings UsageMultiple Strings Xxxx Usage Examples ParametersS 1.5 or 1.11 Y Introduction Error BitsLeftmost Number 02000000 1000000008000000 04000000 Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37 UDP 2-50,B-3 Telnet 2-48,2-68