Show Hostlist, Show IPsecurity, Show NetWare | Lantronix MSS

Command Reference

Show Hostlist

2.87 Show Hostlist

SHOW HOSTLIST

Displays the current list of remote hosts to use for multihost mode connections.

See Also

Status Displays, page 5-6;Multihost Mode, page 5-11; Hostlist, page 2-58.

2.88 Show IPsecurity

SHOW IPSECURITY

Displays the current TCP/IP security table. Each address or range is shown, along with the direction of concern.

See Also

Status Displays, page 5-6.

2.89 Show NetWare

SHOW NETWARE

Displays NetWare characteristics, including frame types, routing status, and internal network number.

Errors	Does not apply to MSSLite, MSS-VIA, or the MSS4.
See Also	Status Displays, page 5-6.

2.90 Show Nodes

 LAT 

SHOW NODES    SPX 

Displays information about the desired LAT or SPX service nodes.

ErrorsAll nodes will be shown if no node is specified.

Does not apply to the MSS-Via, MSS4, or MSSLite.

ParametersLAT

Shows LAT nodes identification strings and availability.

2-64

Image 73

Lantronix MSS manual Show Hostlist, Show IPsecurity, Show NetWare, Show Nodes, ParametersLAT

Contents

MSS Reference Manual Part Number Contents Contents Iii Index What’s New Command Syntax Key Purpose Command Line Editing About This Manual Help Command Reference Backward Change 80211 EnabledChange Change 80211 Antenna Defaults Restrictions Change 80211 Fragmentation ErrorsChange 80211 MAC Address Parameters Examples Change 80211 Network Mode Change 80211 Region Change 80211 Power Change 80211 RTS Change 80211 Reset Change 80211 WEP Current port only Change Access Change Autobaud DefaultsDynamic See Also Change Autostart Dashes for ranges Change Bootgateway Change Backward Switch DefaultsEnabled Change BootpChange Break Restrictions Requires privileged user status ParametersPort Defaults Bytes DefaultsNone See AlsoChange Buffering Change Charsize Change Datasend Condition has been detected Restrictions Change Dedicated Command on Change Domain Change Dhcp Change DTRWait Change DSRLogout Change Flow Control DefaultsDisabled Change Gateway Change Forward Switch DefaultsDisabled See Also Change Inactive TimerChange Inactive Logout Change Incoming Change IPSecurity Change IPAddress Change LAT CircTimer Change LAT Identification Change LAT GroupsChange Loadhost Change Local Switch Change Modem Control Change Loginpass Change Name Change Modem Emulation Change NetWare Encapsulation Change Nameserver Change NetWare Loadhost Change NetWare Internal Network Change Parity Change NetWare RoutingParametersfileserver Change Passflow Change Password Limit Change Password Incoming Change Portname Change Password Protect Change Preferred Change Rarp Change Privpass Change Retransmit Limit Change Rlogin Change RS485 Change Secondary Change Signal CheckChange Session Limit Change SNMPSetComm Change Silentboot Change Speed Change Software Two colons and the startup file name of up to 47 characters Change Startup Change Stopbits Defaults See AlsoChange Subnet Mask Change TCPKeepalive DefaultsConsoleChange Telnetdest Change Termtype Change TelnetpadParameters Examples Daytime is only supported over UDP Change Timeserver Change Wins Change Verify Crypt Password Disk Digit Meaning Checks the MSS filesystem and corrects any problems Rf command Disconnect Delete IPSecurityFinger Parametersusername Hostlist ForwardParameterskeyword Initialize Show Hostlist command ParametersserviceName ParametersDelay78 LAT Logout Port Ping NetstatResume Parametershostname 84 RTC RloginParametersIPaddress Show Set PrivilegedParametersAntenna Show IPsecurity Show HostlistShow NetWare Show Nodes Show RS485 Show PortsShow Server ParametersAll ParametersBootparams Show ServicesShow Session Show Users Show SnmpShow Version Source Telnet 100 SPXParametersSAPname Zero Test Full Contact Information Problem Report Procedure Available Strings UsageMultiple Strings Xxxx Usage Examples ParametersS 1.5 or 1.11 Y Introduction Error BitsLeftmost Number 08000000 1000000004000000 02000000 Rightmost Number Unassigned 00000004 Internal error 00000002 00000001 Index Security 2-27,2-57,2-64IPX NetWare Login 2-31,2-37 UDP 2-50,B-3 Telnet 2-48,2-68