Return to Section TOC
Return to Section TOC
Return to Master TOC
Return to Master TOC
|
|
|
|
|
|
|
|
|
|
|
| OPERATION | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
OPERATIONAL | FEATURES |
| AND | • After the 5 second "Hold" period, the meter displays the | ||||||||||||||
CONTROLS |
|
|
|
|
|
|
|
|
|
|
|
|
| set WFS (CV modes) or Amp (CC modes) value. | ||||
POWER | 2. VOLT / TRIM METER |
| ||||||||||||||||
The specific system component function of the pc board will | This meter displays either the voltage or trim value | |||||||||||||||||
be configurable by dip switch or by software configuration | ||||||||||||||||||
tool. Dip switch configuration is as follows: Refer to DIP | depending on the status of the machine. Located | |||||||||||||||||
switch settings of figures below. |
|
|
|
|
|
| below the display are the text "Volts" and "Trim." An | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| LED light is illuminated next to one of these in order | |
Notes: |
|
|
|
|
|
|
|
|
|
|
|
|
| to indicate the units of the value displayed in the | ||||
1. Basic Power | meter. |
| ||||||||||||||||
Interface (UI), and up to two wire drives (a dual head wire | CV Processes |
| ||||||||||||||||
drive counts as two). |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
POWER | • Prior to | |||||||||||||||||
meter displays the desired preset Voltage value. | ||||||||||||||||||
|
|
|
|
|
|
|
|
|
| O 1 | 2 | 3 4 5 6 7 | 8 | • Prior to | ||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||
UI/WD PCB - S25629 |
|
|
|
|
| the desired preset Trim value. |
| |||||||||||
|
|
|
|
|
| N |
|
|
|
|
|
|
| |||||
(located on Wire Drive divider panel) |
|
|
|
|
|
| • During Welding, the meter displays actual average | |||||||||||
WD only PCB - S25616 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| volts. |
| |
|
|
|
|
|
|
|
|
|
| O 1 | 2 | 3 4 5 6 7 8 | • After welding, the meter holds | the actual voltage | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
(located on Wire Drive rear access door) |
| N |
|
|
|
| value for 5 seconds. During this time, the display is | |||||||||||
|
|
|
|
| ||||||||||||||
|
|
|
|
|
| |||||||||||||
POWER | blinking to indicate that the machine is in the "Hold" | |||||||||||||||||
period. Output adjustment while in the "Hold" period | ||||||||||||||||||
|
|
|
| O 1 2 | 3 |
| 4 | 5 6 7 8 |
|
|
|
|
|
| results in the "prior to operation" characteristics stat- | |||
UI only PCB - S25952 |
|
|
|
|
|
|
| ed above. |
| |||||||||
N |
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
(located in Control Box) |
|
|
|
|
|
|
|
|
|
|
|
|
| • After the 5 second "Hold" period, the meter displays | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
WD only PCB #1 - S25616 |
|
|
|
|
|
| O 1 2 3 4 | 5 | 6 | 7 | 8 | the set Voltage (GMAW, FCAW) or Trim | ||||||
|
|
|
|
|
| value. |
| |||||||||||
|
|
|
|
|
| N |
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
(located on Wire Drive divider panel) |
|
|
|
|
|
|
|
|
Return to Section TOC
Return to Section TOC
Return to Master TOC
Return to Master TOC
WD only PCB #2 - S25616 |
|
| O 1 | 2 | 3 | 4 | 5 6 7 8 |
N |
|
|
|
| |||
|
|
|
| ||||
(located on Wire Drive rear access door) |
|
|
|
|
|
*See power source manual for additional dip switch settings.
CONTROLS (Refer to Figure BB.2)
1. WIRE FEED SPEED (WFS) / AMP METER
This meter displays either the WFS or current value depending on the status of the machine. Located below the display are the text "WFS" and "Amps." An LED light is illuminated next to one of these in order to indicate the units of the value displayed in the meter.
•Prior to CV operation, the meter displays the desired pre- set WFS value.
•Prior to
•During Welding, the meter displays actual average amps, but may be configured to display actual WFS.
•After welding, the meter holds the actual current or WFS value for 5 seconds. During this time, the display is blink- ing to indicate that the machine is in the "Hold" period. Output adjustment while in the "Hold" period results in the "prior to operation" characteristics stated above.
CC Processes
•The meter displays the status of the output.
•When output is enabled, the meter will display "ON."
•When there is no output, the meter will display "OFF."
FIGURE BB.1
4
|
| 72 | ALUMINUM |
|
| IR PORT | 3/64" | SETUP | |
|
| PULSE 4043 Ar |
| |
5 | WELD MODE |
|
| START OPTIONS |
ARC CONTROL |
|
| END OPTIONS | |
| SET |
|
|