Communication Port PIN Assignments | Quick Eagle Networks DL3800E

B

COMMUNICATION PORT PIN ASSIGNMENTS

RS-449, DC-37 to DB-25 DCE Cable Pin Assignments

Table B-6 describes the RS-449, DC-37 to DB-25 DCE cable pin assignments.

Table B-6 RS-449, DC-37 to DB-25 DCE Cable Pin Assignments

DC-37 DB-25

824

2611

134

3119

22	16

4	3

24	14

62

126

3022

2923

1120

25 10

78

359

1717

197

NC 1

Pinouts

B-5

Image 137

Quick Eagle Networks DL3800E manual Communication Port PIN Assignments, RS-449, DC-37 to DB-25 DCE Cable Pin Assignments

Contents

DL3800E Inverse Multiplexer User’s Guide Remedies and Limitations of Liability Product Limited WarrantyCopyright and Trademarks Disclaimer Year 2000 Compliance Rights to SoftwareISO Compliance Industry Canada International Compliance Vcci Regulatory Compliance Table of Contents Installation Front Panel Interface Diagnostics Appendix C, Factory Default Settings Glossary Index DL3800E Inverse Multiplexer front panel List of Figures 12 DTE Configuration Menu Hssi List of Tables Xvi Organization PrefaceAudience Conventions Symbols Typeface or Purpose SymbolTypography Returning a Unit Quick Eagle Networks Technical SupportTelephone 408 Mail Support@quickeagle.com Internet Send US Your Comments Date Issue Rev Description Pages AffectedDocument Change Record Quick Eagle Networks Technical Publications Xxii Configuration Quick Install GuidePurpose Equipment Needed Terminal Log On Setup Network Configuration DL3800E Inverse Multiplexer User’s Guide July 9 System Overview Introduction System Features Product Features Application System Benefits Functional Description Signal Flow E1 Port Crossover Detection LCA TX LCA Overhead FunctionsDTE Intf Installation Installation Desk Operation And Stacking MountingRack Mounting DC Power Connection Power Cables and ConnectionsAC Power Connection EFS 00.0 Percent Ascii Terminal and Snmp Connection E1 Network ConnectionDTE Cable and Connection Telnet Connection Direct ConnectionModem Connection Daisy Chaining DL3800E Inverse Multiplexer User’s Guide July 9 LOG IN/LOG OFF Terminal Interface Terminal Operation Overview Local/Remote when in the Main Menu, and back to Exit whenGeneral Menu Flow Screen Description Terminal Interface Menu Description Inverse Multiplexer Main Menu CommandsSelect LOCAL/REMOTE Alarm Alarms and StatusLOS LOF YEL AIS DETAIS Common Equipment BPV MN/MJOOF MN/MJ DTE Been set DL3800E Inverse Multiplexer User’s Guide July 9 Statistics Submenu Statistics NET Statistics Menu EFS Parameter DefinitionESR Sesr EB/CV BPVSES BBE UAS Event History Alarm Level Alarm Parameter Definition Configuration Menu Configuration Option Action Unit Configuration To toggle between Off and On DTE Configuration DTE Configuration Menu 11 DTE Configuration Menu Parameter Description/Action Parameter Description/Action DTE Loss Detection CA Mode CRC4 Enable Data TSLOT16 Network Thresholds 14 Network Thresholds Configuration Utilities Menu System Utilities Software Download DL3800E Inverse Multiplexer User’s Guide July 9 Software Download Options RAM Software Options Delete Entire Unit Configuration revert to factory config Delete RAM Code and Revert to ROM Code Login Configuration Parameter Description Snmp Configuration Option Description/Action IP Bridging to a Remote Unit In-Band Snmp to Remote 20 Tests Menu Tests Payload Loopback DTE/Network LoopbackLine Loopback Local Loopback 21 Loopbacks within the DL3800E unit Remote Loopback Detection Manual Network Restoration 22 Manual Network Restoration Menu Logout DL3800E Inverse Multiplexer User’s Guide July 9 General Front Panel InterfaceDisplay Overview Button Overview Enter Button Exit ButtonUP Arrow and Down Arrow Buttons Indication Description Front Panel LEDsRTS/TA CTS/CA Access Levels And Protected Mode TOP Menu Power UP and Reset Select Remote Display Menu Select REMOTE/SELECT Local Display Menu Node Common Equipment Status NET 1-8 Status DTE StatusNET 1-8 Statistics Front Panel Display Explanation Counters were last reset UAS only occurs at the onset of 10 SES Test Menu Test Menu DTE Tests Network Tests Line Loopback Configuration Menu Menu Definition Node Config MenuDTE Config Menu Network Config Node ConfigurationNET N Config Menu Menu DL3800E Inverse Multiplexer User’s Guide July 9 5NODE Configuration Menu Items Node Configuration Menu Items Comm Port Config DTE Configuration Menu Front Panel Interface Network Config Front Panel Interface Network Thresholds NET N Config CON Crcs OFF CON SES CON CrcsConses CON UAS CON UAS OFF 15.MIN.MI.BPV 24.HR.MJ.UASOFF 24.HR.MJ.ESOFF24.HR.MJ.SESOFF Equipment Return and Repair DiagnosticsRunning Diagnostic Tests Tests Menu DTE/Network Loopback TestLocal Loopback Test Payload Loopback and Line Loopback Tests Possible Sources of ProblemsTroubleshooting the DL3800E Network Tests Menu Problem Solution Troubleshooting 2 Troubleshooting 3 Troubleshooting 4 ProblemSolution Parameter Setting SpecificationsE1 Network Interface External Clock Interface Ascii VT100 DTE InterfaceInterface Power DiagnosticsFront Panel Environmental External Alarm Contacts Physical /CONNECTORSDimensions DB-9 Alarm Designations Signal Specifications DL3800E Inverse Multiplexer User’s Guide July 9 Pinouts DCE ConnectorsTerminal Connection CTS Channel 1 Data Cable PIN Assignments DB-25 Signal Name Scte DB-25SCR SCT DB-25 to DC-37 Data Port Cable Pin Assignments DC-37 DB-25 Signal Name DC-37 DB-25 Communication Port PIN AssignmentsRS-449, DC-37 to DB-25 DCE Cable Pin Assignments DB-25 DE-9 E1 Network PIN AssignmentsDB-25TO DE-9 Adapter Pinouts To DB-25 Cable Pinouts External Clock Connector PIN AssignmentsSignal Name DB-25 DL3800E Inverse Multiplexer User’s Guide July 9 Alarm Pinout DTE Clock Rates DC Power Connections Unit Setting Factory Default Settings Snmp Configuration Setting Network SettingNetwork Threshold Setting Bits & Parity Tests SettingStop Bits ALL Loopbacks & Tests DL3800E Inverse Multiplexer User’s Guide July 9 Glossary Bit error BES Bursty Errored SecondsBit Error Rate BER Blue Alarm Broadband CMI Control Mode IdleBPV Bipolar Violation Central office CO CSU Channel Service Unit ConnectorDacs Digital Access Cross-Connect Switch CPE Customer Premises Equipment DS-1 Digital Signal Level DS-0 Digital Signal LevelDS-3 Digital Signal Level DSU/CSU Data Service Unit/Channel Service Units EER Excessive Error Rate DSX-1 Digital Signal Cross Connect LevelEFS Error Free Seconds DSU Loopback Failed signal state ES Errored SecondFE Framing Errors Equalization Framing Frame relayFrame ground Frequency LOF Loss of Frame LOS Loss of SignalLofc Loss of Frame Count Loopback Multidrop OOS Out of ServiceNetwork NI Network Interface Polarity RI Ring IndicatorPort Protocol RS232-C SES Severely Errored SecondRS449 RTSRequest to Send Smds Switched Multimegabit Data Service SG Signal GroundSimplex current Slip Serial Line IP Telnet CarrierTransmitter UAS Unavailable Seconds Cable Index NMS Port Snmp A-2