Roland XV-88 owner manual 272, Program Change, Channel Pressure, Pitch Bend Change

MIDI Implementation

❍Vibrato Delay (Controller number 78)

Status	2nd byte	3rd byte
BnH	4EH	vvH
n = MIDI channel number:			0H	- FH (ch.1 - 16)
vv = Vibrato Delay value (relative change):			00H - 7FH (-64 - 0 - +63)

*The vibrato delay will change in GM mode.

❍General Purpose Controller 5 (Controller number 80)

Status	2nd byte	3rd byte
BnH	50H	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Control value:		00H - 7FH (0 - 127)

*The Level parameter (PATCH/TVA/TVA) of Tone 1 will change.

❍General Purpose Controller 6 (Controller number 81)

Status	2nd byte	3rd byte
BnH	51H	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Control value:		00H - 7FH (0 - 127)

*The Level parameter (PATCH/TVA/TVA) of Tone 2 will change.

❍General Purpose Controller 7 (Controller number 82)

Status	2nd byte	3rd byte
BnH	52H	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Control value:		00H - 7FH (0 - 127)

*The Level parameter (PATCH/TVA/TVA) of Tone 3 will change.

❍General Purpose Controller 8 (Controller number 83)

Status	2nd byte	3rd byte
BnH	53H	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Control value:		00H - 7FH (0 - 127)

*The Level parameter (PATCH/TVA/TVA) of Tone 4 will change.

❍Portamento control (Controller number 84)

Status	2nd byte	3rd byte
BnH	54H	kkH
n = MIDI channel number:		0H - FH (ch.1 - 16)
kk = source note number:		00H - 7FH (0 - 127)

*A Note-on received immediately after a Portamento Control message will change continuously in pitch, starting from the pitch of the Source Note Number.

*If a voice is already sounding for a note number identical to the Source Note Number, this voice will continue sounding (i.e., legato) and will, when the next Note-on is received, smoothly change to the pitch of that Note-on.

*The rate of the pitch change caused by Portamento Control is determined by the Portamento Time value.

❍Effect 1 (Reverb Send Level) (Controller number 91)

Status	2nd byte	3rd byte
BnH	5BH	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Reverb Send Level:		00H - 7FH (0 - 127)

*In Performance mode the Reverb parameter (PERFORM/EFFECTS/OUTPUT) will change.

❍Effect 3 (Chorus Send Level) (Controller number 93)

Status	2nd byte	3rd byte
BnH	5DH	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Chorus Send Level:		00H - 7FH (0 - 127)

*In Performance mode the Chorus parameter (PERFORM/EFFECTS/OUTPUT) will change.

❍RPN MSB/LSB (Controller number 100, 101)

Status	2nd byte	3rd byte
BnH	65H	mmH
BnH	64H	llH

n = MIDI channel number: 0H - FH (ch.1 - 16)

mm= upper byte (MSB) of parameter number specified by RPN ll = lower byte (LSB) of parameter number specified by RPN

<<< RPN >>>

Control Changes include RPN (Registered Parameter Numbers), which are extended. When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any order) should be sent in order to select the parameter, then

Data Entry (Controller numbers 6 and 38) should be sent to set the value. Once RPN messages are received, Data Entry messages that is received at the same MIDI channel after that are recognized as changing toward the value of the RPN messages. In order not to make any mistakes, transmitting RPN Null is recommended after setting parameters you need.

This device receives the following RPNs.

RPN	Data entry
MSB, LSB	MSB, LSB	Notes
00H, 00H	mmH, llH	Pitch Bend Sensitivity
		mm: 00H - 18H (0 - 24 semitones)
		ll: ignored (processed as 00H)
		Up to 2 octave can be specified in semitone steps.
		* In Performance mode, the BendRng parameter
		(PERFORM/PART/PITCH) will change.
00H, 01H	mmH, llH	Channel Fine Tuning
		mm, ll: 20 00H - 40 00H - 60 00H
		(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
		* In Performance mode, the Fine parameter
		(PERFORM/PART/PITCH) will change.
00H, 02H	mmH, llH	Channel Coarse Tuning
		mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
		ll: ignored (processed as 00H)
		* In Performance mode, the Coarse parameter
		(PERFORM/PART/PITCH) will change.
00H, 05H	mmH, llH	Modularion Depth Range
		mm: 00 00H - 06 00H
		(0 - 16384 x 600 / 16384 cent)
		* Not received in Performance mode or Patch
		mode.
7FH, 7FH	---, ---	RPN null
		RPN and NRPN will be set as “unspecified.”
		Once this setting has been made, subsequent
		Parameter values that were previously set will
		not change.
		mm, ll: ignored

●Program Change

Status	2nd byte
CnH	ppH
n = MIDI channel number:		0H - FH (ch.1 - 16)
pp = Program number:		00H - 7FH (prog.1 - prog.128)

*Not received in Performance mode when the Program Change parameter (PERFORM/ MIDI/RxSWITCH) is OFF.

●Channel Pressure

Status	2nd byte
DnH	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Channel Pressure:		00H - 7FH (0 - 127)

*Not received in Performance mode when the Caf parameter (PERFORM/MIDI/ RxSWITCH) is OFF.

●Pitch Bend Change

Status	2nd byte	3rd byte
EnH	llH	mmH
n = MIDI channel number:		0H - FH (ch.1 - 16)

272