SINGLE: When the keys are pressed, the single specified Part (current Part) are played. Zone settings are ignored. Transmission of MIDI messages from the keyboard controller section to external MIDI devices will be determined by the Receive switch (Rx Sw parameter) setting for the current Part

Part 1

 

Part 2

 

Part 15

 

Part 16

(Rx ch.1)

 

(Rx ch.2)

 

(Rx ch.15)

 

(Rx ch.16)

MIDI OUT

(Tx ch.1)

If you have selected a LAYER-type Performance, the upper right of the PERFORM PLAY page will indicate “LAYER p *” (* is the Part number). If you have selected a SINGLE-type Performance, “part= *” (* is the Part number) will be displayed.

You can also set the Key Mode parameter on the PERFORM PLAY page. By holding down [SHIFT] and pressing [SOLO], you can switch between SINGLE and

LAYER.

Setting the Keyboard Range (KEY RANGE)

When a Single Performance is selected, this setting is disabled.

KEY RANG (Key Range)

These parameters set the key range that will be transmitted from the keyboard for each Zone. Use this when you wish to play different Patches in different areas of the keyboard.

Lower (Key Range Lower)

Specify the lower limit of the range.

Upper (Key Range Upper)

Specify the upper limit of the range.

Chapter 4. Zone Settings

When the Key Range (p. 73) is set for each individual Tone in a Patch, sounds are produced in the range where the Key Range of each Tone and the Key Range for the Zone overlap.

Key range specified for Performance

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Key range specified for Patch

Chapter

The range in which notes will play

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If you attempt to raise the lower key higher than the upper key, or to lower the upper key below the lower key, the other value will be automatically modified to the same setting.

Making Settings for Transmitting MIDI (MIDI)

These parameters determine how each Zone will transmit MIDI messages.

When a Single Performance is selected, this setting is disabled.

MIDI

Channel (MIDI Transmit Channel)

Specifies the MIDI transmit channel for each Zone.

Tx (Transmit Switch)

Determines, for each Zone, whether or not data generated by the keyboard controller section is sent as MIDI messages from the MIDI OUT connector.

Normally you will leave this ON, but you can turn it OFF when you do not want the XV-88 to control external sound generators.

59

Page 59
Image 59
Roland XV-88 Setting the Keyboard Range KEY Range, Making Settings for Transmitting Midi Midi, Lower Key Range Lower