Roland XV-88 owner manual 277, Volume Controller number

❍Volume (Controller number 7)

Status	2nd byte	3rd byte
BnH	07H	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Volume:		00H - 7FH (0 - 127)

*In Performance (Zone) mode, these messages are not transmitted when Volume parameter (ZONE/EXT CONTROL/EXT CTRL) is NO-SEND.

❍Panpot (Controller number 10)

Status	2nd byte	3rd byte
BnH	0AH	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Panpot:		00H - 40H - 7FH (Left - Center - Right),

*In Performance (Zone) mode, these messages are not transmitted when Pan parameter (ZONE/EXT CONTROL/EXT CTRL) is NO-SEND.

❍Expression (Controller number 11)

Status	2nd byte	3rd byte
BnH	0BH	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Expression:		00H - 7FH (0 - 127)

❍Hold 1 (Controller number 64)

Status	2nd byte	3rd byte
BnH	40H	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Control value:		00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON

*When Continuous parameter (SYSTEM/CONTROL/HOLD PEDAL) is OFF, just only 00H (0FF) and 40H (0N) can be send as the control value.

❍Portamento (Controller number 65)

Status	2nd byte	3rd byte
BnH	41H	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Control value:		00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON

❍Resonance (Controller number 71)

Status	2nd byte	3rd byte
BnH	47H	vvH
n = MIDI channel number:		0H	- FH (ch.1 - 16)
vv= Resonance value (relative change):		00H - 7FH (-64 - 0 - +63)

❍Release Time (Controller number 72)

Status	2nd byte	3rd byte
BnH	48H	vvH
n = MIDI channel number:		0H	- FH (ch.1 - 16)
vv = Release Time value (relative change):		00H - 7FH (-64 - 0 - +63)

❍Attack time (Controller number 73)

Status	2nd byte	3rd byte
BnH	49H	vvH
n = MIDI channel number:		0H	- FH (ch.1 - 16)
vv = Attack time value (relative change):		00H - 7FH (-64 - 0 - +63)

❍Cutoff (Controller number 74)

Status	2nd byte	3rd byte
BnH	4AH	vvH
n = MIDI channel number:		0H	- FH (ch.1 - 16)
vv = Cutoff value (relative change):		00H - 7FH (-64 - 0 - +63)

❍General Purpose Controller 5 (Controller number 80)

Status	2nd byte	3rd byte
BnH	50H	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Control value:		00H - 7FH (0 - 127)

❍General Purpose Controller 6 (Controller number 81)

Status	2nd byte	3rd byte
BnH	51H	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Control value:		00H - 7FH (0 - 127)

MIDI Implementation

❍General Purpose Controller 7 (Controller number 82)

Status	2nd byte	3rd byte
BnH	52H	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Control value:		00H - 7FH (0 - 127)

❍General Purpose Controller 8 (Controller number 83)

Status	2nd byte	3rd byte
BnH	53H	vvH
n = MIDI channel number:		0H - FH (ch.1 - 16)
vv = Control value:		00H - 7FH (0 - 127)

❍Portamento control (Controller number 84)

Status	2nd byte	3rd byte
BnH	54H	kkH
n = MIDI channel number:		0H - FH (ch.1 - 16)
kk = source note number:		00H - 7FH (0 - 127)

❍RPN MSB/LSB (Controller number 100, 101)

Status	2nd byte	3rd byte
BnH	65H	mmH
BnH	64H	llH

n = MIDI channel number: 0H - FH (ch.1 - 16)

mm= upper byte (MSB) of parameter number specified by RPN ll = lower byte (LSB) of parameter number specified by RPN

<<< RPN >>>

When execute the GM Data Transfer, Program Change, Data Entry, and following RPN messages will transmit.

Control Changes include RPN (Registered Parameter Numbers), which are extended. When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any order) should be sent in order to select the parameter, then

Data Entry (Controller numbers 6 and 38) should be sent to set the value. Once RPN messages are received, Data Entry messages that is received at the same MIDI channel after that are recognized as changing toward the value of the RPN messages. In order not to make any mistakes, transmitting RPN Null is recommended after setting parameters you need.

This device transmits the following RPNs.

RPN	Data entry
MSB, LSB	MSB, LSB	Notes
00H, 00H	mmH, llH	Pitch Bend Sensitivity
		mm: 00H - 18H (0 - 24 semitones)
		ll: ignored (processed as 00H)
00H, 01H	mmH, llH	Channel Fine Tuning
		mm, ll: 20 00H - 40 00H - 60 00H
		(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
00H, 02H	mmH, llH	Channel Coarse Tuning
		mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
		ll: ignored (processed as 00H)
00H, 05H	mmH, llH	Modulation Depth Range
		mm, ll: 00 00H - 06 00H
		(0 - 16384 x 600 / 16384 cent)
7FH, 7FH	---, ---	RPN null
		RPN and NRPN will be set as “unspecified.”
		Once this setting has been made, subsequent

●Program Change

Status	2nd byte
CnH	ppH
n = MIDI channel number:		0H - FH (ch.1 - 16)
pp = Program number:		00H - 7FH (prog.1 - prog.128)
* These messages are transmitted when Performance, Patch or Rhythm set is selected. But			Appendices
not transmitted when Program parameter (SYSTEM/MIDI/TRANSMIT MIDI) is OFF.

* In Performance (Zone) mode, these messages are not transmitted when P.C# parameter (ZONE/EXT CONTROL/EXT P.C) is NO-SEND.

277