Roland XV-88 owner manual 273

mm, ll = Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)

*Not received when the Bender parameter (PATCH/CONTROL/CTRL RxMIDI) is OFF.

*Not received in Performance mode when the Bnd parameter (PERFORM/MIDI/ RxSWITCH) is OFF.

■Channel Mode Messages

*Not received in Performance mode when the Rx Sw parameter (PERFORM/MIDI/ MIDI) is OFF.

●All Sounds Off (Controller number 120)

Status	2nd byte	3rd byte
BnH	78H	00H

n = MIDI channel number: 0H - FH (ch.1 - 16)

*When this message is received, all notes currently sounding on the corresponding channel will be turned off.

●Reset All Controllers (Controller number 121)

Status	2nd byte	3rd byte
BnH	79H	00H

n = MIDI channel number: 0H - FH (ch.1 - 16)

*When this message is received, the following controllers will be set to their reset values.

Controller	Reset value
Pitch Bend Change	+/-0 (center)
Polyphonic Key Pressure	0	(off)
Channel Pressure	0	(off)
Modulation	0	(off)
Breath Type	0	(min)
Expression	127 (max)
Hold 1	0	(off)
Sostenuto	0	(off)
Soft	0	(off)
Hold 2	0	(off)
RPN	unset; previously set data will not change
NRPN	unset; previously set data will not change

●All Notes Off (Controller number 123)

Status	2nd byte	3rd byte
BnH	7BH	00H

n = MIDI channel number: 0H - FH (ch.1 - 16)

*When All Notes Off is received, all notes on the corresponding channel will be turned off. However, if Hold 1 or Sostenuto is ON, the sound will be continued until these are turned off.

●OMNI OFF (Controller number 124)

Status	2nd byte	3rd byte
BnH	7CH	00H

n = MIDI channel number: 0H - FH (ch.1 - 16)

*The same processing will be carried out as when All Notes Off is received.

●OMNI ON (Controller number 125)

Status	2nd byte	3rd byte
BnH	7DH	00H

n = MIDI channel number: 0H - FH (ch.1 - 16)

*The same processing will be carried out as when All Notes Off is received. OMNI ON will not be turned on.

●MONO (Controller number 126)

Status	2nd byte	3rd byte
BnH	7EH	mmH
n = MIDI channel number:		0H - FH (ch.1 - 16)
mm = mono number:		00H - 10H (0 - 16)

*The same processing will be carried out as when All Notes Off is received.

*In Performance mode, the Mno/Pol parameter (PERFORM/PART/MONO/POL) will change.

MIDI Implementation

●POLY (Controller number 127)

Status	2nd byte	3rd byte
BnH	7FH	00H

n = MIDI channel number: 0H - FH (ch.1 - 16)

*The same processing will be carried out as when All Notes Off is received.

*In Performance mode, the Mno/Pol parameter (PERFORM/PART/MONO/POL) will change.

■System Realtime Message

●Timing Clock

Status

F8H

*This message will be received if the Clock Source parameter (SYSTEM/SETUP/SYSTEM SETUP) is MIDI.

●Active Sensing

Status

FEH

*When Active Sensing is received, the unit will begin monitoring the intervals of all further messages. While monitoring, if the interval between messages exceeds 420 ms, the same processing will be carried out as when All Sounds Off, All Notes Off and Reset All Controllers are received, and message interval monitoring will be halted.

■System Exclusive Message

Status	Data byte	Status
F0H	iiH, ddH, ......,eeH	F7H
F0H:	System Exclusive Message status
ii = ID number:	an ID number (manufacturer ID) to indicate the manufacturer whose
	Exclusive message this is. Roland's manufacturer ID is 41H.
	ID numbers 7EH and 7FH are extensions of the MIDI standard;
	Universal Non-realtime Messages (7EH) and Universal Realtime
	Messages (7FH).
dd,...,ee = data:	00H - 7FH (0 - 127)
F7H:	EOX (End Of Exclusive)

Of the System Exclusive messages received by this device, the Universal Non-realtime messages and the Universal Realtime messages and the Data Request (RQ1) messages and the Data Set (DT1) messages will be set automatically.

●Universal Non-realtime System Exclusive Messages

❍Identity Request Message

Status	Data byte	Status
F0H	7EH, dev, 06H, 01H	F7H
Byte	Explanation
F0H	Exclusive status
7EH	ID number (Universal Non-realtime Message)
dev	Device ID (dev: 00H - 1FH (1 - 32), the initial value is 10H (17).)
06H	Sub ID#1 (General Information)
01H	Sub ID#2 (Identity Request)
F7H	EOX (End Of Exclusive)

*When this message is received, Identity Reply message (p. 278) will be transmitted.

❍GM1 System On

Status	Data byte	Status
F0H	7EH, 7FH, 09H, 01H F7H
Byte	Explanation
F0H	Exclusive status
7EH	ID number (Universal Non-realtime Message)
7FH	Device ID (Broadcast)
09H	Sub ID#1 (General MIDI Message)
01H	Sub ID#2 (General MIDI 1 On)
F7H	EOX (End Of Exclusive)

*When this messages is received, this instrument will turn to the GM1 mode.

*Not received when the Rx GM On parameter (SYSTEM/MIDI/SYSTEM MIDI) is OFF.

Appendices

273