Roland XV-88 owner manual Changing How the Effects Are Applied, Applying LFO to Modulate Sounds

Chapter 5. Creating Patches

●Changing How the Effects Are Applied

DRY LEVEL: Changes the volume of dry sounds.

CHORUS SEND: Changes the amount of Chorus.

REVERB SEND: Changes the amount of Reverb.

●Applying LFO to Modulate Sounds

LFO1/LFO2 PCH DEPTH: Changes the vibrato depth.

LFO1/LFO2 TVF DEPTH: Changes the wah depth.

LFO1/LFO2 TVA DEPTH: Changes the tremolo depth.

LFO1/LFO2 PAN DEPTH: Changes the effect that the LFO

will have on pan.

LFO1/LFO2 RATE: Changes the speed of the LFO cycles.

●Changing the Pitch Envelope

PIT ENV A-TIME: Changes the T1 parameter of the pitch

envelope.

PIT ENV D-TIME: Changes the T2 and T3 parameters of the

pitch envelope.

PIT ENV R-TIME: Changes the T4 parameter of the pitch

envelope.

●Changing the TVF Envelope

TVF ENV A-TIME: Changes the T1 parameter of the TVF

envelope.

TVF ENV D-TIME: Changes the T2 and T3 parameters of the

TVF envelope.

TVF ENV R-TIME: Changes the T4 parameter of the TVF

envelope.

●Changing the TVA Envelope

TVA ENV A-TIME: Changes the T1 parameter of the TVA

envelope.

TVA ENV D-TIME: Changes the T2 and T3 parameters of the

TVA envelope.

TVA ENV R-TIME: Changes the T4 parameter of the TVA

envelope.

●Splitting Tones That Are Played

TMT

•If the Matrix Controller is used to split Tones, set the TMT Velocity Control parameter (PATCH/COMMON/ TMT VELO CONTROL) to OFF, and the TMT Ctrl Sw parameter (PATCH/CONTROL/CONTROL&BENDER) to ON (p. 72, p. 78).

•If the Matrix Controller is used to split Tones, we recommend setting the Sns to +63. Selecting a lower value may prevent switching of the Tones. Furthermore, if you want to reverse the effect, set the value to -63.

•When you want to use the Matrix Controller to make the switch between Tones more smoothly, set the L.Fade and U.Fade parameters (PATCH/COMMON/TMT VELO RANG) (p. 73). The higher the values set, the smoother the switch is between the Tones.

●Changing the Depth of Frequency Modulation for FXM

FXM DEPTH

●Changing Specific Multi-Effects Parameters

MFX CTRL1: The specified parameter is changed by the MFX CTRL1 Destination parameter.

MFX CTRL2: The specified parameter is changed by the MFX CTRL2 Destination parameter.

MFX CTRL3: The specified parameter is changed by the MFX CTRL3 Destination parameter.

MFX CTRL4: The specified parameter is changed by the MFX CTRL4 Destination parameter.

No effects are available, even with the Matrix Controller, when the settings are such that no Multi-effects are applied.

Sns (Matrix Control Sensitivity)

Sets the amount of the Matrix Controller’s effect that is applied. To make an increase in the currently selected value (to get higher values, move to the right, increase rates, and so on), select a positive value; to make a decrease in the currently selected value (to get lower values, move to the left, decrease rates, and so on), select a negative value. When both positive and negative are selected, the changes are greater as the value increases. To have no effect applied, select 0.

Tone (Matrix Control Tone)

Matrix Control Tone selects the Tone to which the effect is applied when using the Matrix Controller.

Indicated from left to right are Tones 1, 2, 3, and 4. Tones to which effects are applied are indicated by a circle (o) for the setting; Tones to which no effects are applied are indicated by an underline (_). With a setting of R, the effect will be inverted.

80