Sony 930, 950, 900 manual VCS-700, Video Selector

7 7-7.VCS-700, Video Selector

7-7-1Front and Rear Panels

1 POWER switch and indicator

Front panel POWER VIDEO SELECTOR

3CHARACTER INPUT connectors

2PIX 1 through PIX 6 INPUT connectors

Rear Panel

8WF 1 through WF 6 INPUT connectors

9 WF A INPUT connector

q; WF A OUTPUT connector qa WF B OUTPUT connector

4PIX A INPUT connector

5PIX A OUTPUT connector

6PIX B OUTPUT connector

7 SYNC OUT connector

qg -AC IN connector

qf I/O PORT connector

qd REMOTE connector

qs WF MODE connector

aPOWER switch and indicator

This switch turns the power ON and OFF. The indicator illuminates when power is switched on.

bPIX1 through PIX6 INPUT (picture monitor 1

through 6 inputs) connectors (BNC type) Accept video signals for a picture monitor. Connect each of these connectors to the PIX2 OUTPUT connector on the CCU-700A/700AP Camera Control Unit. The signal loss of a connecting cable up to about 30 meters (99 feet) long can be compensated for with the switch on the internal board. For details, refer to the system manual.

cCHARACTER INPUT connectors (BNC type) Accept character signals. The input signal is mixed with the signal output from the PIX OUTPUT connector. Connect to the CHARACTER connector on the CNU- 700 Camera Command Network Unit. When using two VCS-700 units, connect either of these connectors to the CHARACTER INPUT connector on a second VCS- 700. When a bridge connection is not made, be sure to terminate with 75 ohms.

dPIX A INPUT (picture monitor A input) connector

(BNC type)

Connect to the PIX A OUTPUT connector on a second VCS-700 when using two or more VCS-700 selectors.

ePIX A OUTPUT (picture monitor A output)

connector (BNC type)

Supplies a video signal for a picture monitor. Select the output signal with the camera select buttons on an MSU-700 or by command from the I/O PORT connector on the VCS-700 Video Selector. When using two or more VCS-700 units, connect this connector to the PIX A INPUT connector on each subsequent VCS- 700, and a picture monitor to the PIX A OUTPUT connector on the final VCS-700 in the series connection.

fPIX B OUTPUT (picture monitor B output)

connector (BNC type)

Supplies the same video signal for a picture monitor as the PIX A OUTPUT connector. The signal loss of a connecting cable up to about 100 meters (330 feet) long can be compensated for with the switch on the internal board. When you connect a picture monitor using a long connecting cable, connect it to this connector. When using two or more VCS-700 units connected in series, connect a picture monitor to the PIX B OUTPUT loop connector on the VCS-700 whose PIX A OUTPUT connector is not used for series connection. For details on cable compensation, refer to the system manual.

gSYNC OUT (sync signal output) connector (BNC

type)

Supplies the sync signal for a picture monitor.

hWF1 through WF6 INPUT (waveform monitor 1

through 6 input) connectors (BNC type)

Accept video signals for a waveform monitor. Connect these connectors as required to the WF2 OUTPUT connector on CCU-700A/700AP Camera Control Units. The signal loss of a connecting cable up to about 30 meters (99 feet) long can be compensated for with the switch on the internal board. For details, refer to the system manual.

iWF A INPUT (waveform monitor A input) connector (BNC type)

Connect to the WF A OUTPUT connector on a second VCS-700 when using two of these units.

jWF A OUTPUT (waveform monitor A output) connector (BNC type)

Supplies the video signal for a waveform monitor. Select the output signal with the camera select buttons on an MSU-700 or by command from the I/O PORT connector on a VCS-700. When using two or more VCS-700 units, connect this connector to the WF A INPUT connector on each subsequent VCS-700, and a

HDC-900/950/930 Series Product Information Manual Chapter 7 Location and Function of Parts and Controls 105