Sony 950, 930, 900 manual Picture Monitor buttons, Waveform Monitor buttons, Camera select block

7	l PICTURE MONITOR buttons	The signal corresponding to the lit button is output.
	Press to select the output signal from the PIX2	R/G/B: Select the R signal, G signal, or B signal. The
	OUTPUT connector of CCU.	signals can be selected either independently or in
	The signal corresponding to the lit button is output.	combination. When any of these buttons is pressed,
	R/G/B: Select the R signal, G signal, or B signal. The	the SEQ and ENC circuits are turned off.
	signals can be selected either independently or in	SEQ (sequence): When this button is pressed, the R/
	combination. When any of these buttons is pressed,	G/B circuits are turned off, and the SEQ signal is
	the ENC circuit is turned off.	output. You can monitor the waveforms of the three
	ENC (encode): When this button is pressed, the R/G/	R, G, and B signals in sequence on a waveform
	B circuits are turned off, and the ENC signal is	monitor.
	output.	ENC (encode): When this button is pressed, the R/G/
		B and SEQ circuits are turned off, and the ENC
	m WAVEFORM MONITOR buttons	signal is output.
	Press to select the output signal from the WF2 OUTPUT
	connector of CCU.	n Camera select block

12

PARA MULTI

TALLY

PANEL

ACTIVE

1 2 3 4 5 6 7 8 9 10 11 12

EXPAND

3

4

5

76

APANEL ACTIVE button

Press and light up this button to permit the cameras selected with the camera select buttons to be controlled from this unit. The IRIS/ MB ACTIVE button also lights up. If you press

the button when lit, it goes dark and the operation panel of this unit is locked.

BPARA (parallel mode) button

Press and light up this button to activate Parallel mode, which enables concurrent operation with another control panel. If you press the button

when lit, it goes dark and Parallel mode is canceled.

CMULTI indicators

Show the Master/Slave status of the corresponding cameras 1 through 12 (when the EXPAND button is not lit) or 13 through 24 (when the EXPAND button is lit).

The indicator for the camera which is specified as the master for Master/Slave mode lights in green. The indicators for the slave cameras light in orange. They light in red during the auto setup

of the corresponding cameras. If an error occurs during the auto setup and the operation is interrupted, they will flash in red.

DTALLY indicators

Show the tally status of the corresponding cameras 1 through 12 (when the EXPAND button is not lit) or 13 through 24 (when the EXPAND button is lit). The corresponding indicator lights in red when a red tally is sent to a camera, and it lights in green when a green tally is sent. When both red and green tally are

sent, it lights in orange. When a call signal is sent to the camera, the indicator rapidly flashes in red.

EActive indicators

Show the control status of the corresponding cameras 1 through 12 (when the EXPAND button is not lit) or 13 through 24 (when the EXPAND button is lit). The indicators for the cameras under control of this unit light in green and the indicators for the cameras under control of another control panel light in orange. An indicator whose corresponding camera (or

camera control unit) is not connected does not light. An indicator lights in red when an error is detected and the self-diagnostic functions are activated in the corresponding camera or camera control unit.

FCamera select buttons

Select the cameras to be controlled from this unit. Press and light up the button corresponding to each desired camera. Cameras 1 through 12 are selected when the EXPAND button is not lit, and cameras 13 through 24 are selected when the EXPAND

button is lit.

GEXPAND button

Press to select the group to be selected with the camera select buttons. Cameras 1 through 12 can be selected when this button is not lit, and cameras 13 through 24 can be selected when this button is lit.

Note

An appropriate camera command network unit (CNU- 700, etc.) is required to control multiple cameras using the camera select function.

o Filter control block

1 2

1	2	3	4	5
FILTER CTRL		ND
A	B	C	D	E

CC

3

AFILTER CTRL (filter control) button

Press and light up the button to enable filter selection with the CC and ND filter select buttons of this unit.

BND (ND filter select) buttons

While the FILTER CTRL button is lit, press and light up one of these buttons to select the corresponding ND filter.

HDC-900/950/930 Series Product Information Manual Chapter 7 Location and Function of Parts and Controls 109