Sony 930, 950 Back tally lamp, Memory Stick media card section, Return Select knob, RET 1 button

7	s Back tally lamp
	This lamp lights red when the red tally signal is
	supplied. When the CALL button on the MSU-700A/

750 Master Setup Unit or the RCP-700 series Remote Control Panel is pressed, the lamp lights if previously off or goes off if previously on. The brightness of the lamp may be adjusted using a control provided in the camera.

Attach a supplied number plate (0 through 9) to display the camera number. Lights green when the green tally signal is supplied.

t Memory Stick media card section

Insert a Memory Stick media card into the slot. The lamp lights while writing or reading data to/from a Memory Stick media card.

u RETURN SELECT knob 1

This knob selects from the four return signals from the CCU. By pressing in the RET 1 button, you can view the selected return video signal in the viewfinder.

v RETURN SELECT knob 2

This knob selects from the four return signals from the CCU. By pressing in the RET 2 button, you can view the selected return video signal in the viewfinder.

w RET 1 button

By pressing in this button, you can view the return video signal selected by the RETURN SELECT knob 1, in the viewfinder. Pressing this button again will switch the viewfinder screen display and MONITOR output back to the camera’s video signal.

x RET 2 button

By pressing in this button, you can view the return video signal selected by the RETURN SELECT knob 2, in the viewfinder. Pressing this button again will switch the viewfinder screen display and MONITOR output back to the camera’s video signal.

Note

If both the RET 1 and RET 2 buttons are pressed, RET 1 will be displayed.

y CURSOR STORE button

Press this button to store the size and position of the box cursor in memory.

Note

If the CURSOR ON button is not lit, box cursor information will not be stored.

z CURSOR ON button

When this button is pressed, the button will light up and the box cursor will be displayed on the viewfinder screen. When the button is pressed again, the light will go off and the box cursor will disappear.

wj HEIGHT control

Adjust the height of the box cursor displayed on the viewfinder screen within the effective resolution area.

wk V-POSI (vertical position) control

Adjust the vertical position of the box cursor displayed on the viewfinder screen within the effective resolution area.

wl WIDTH control

Adjust the width of the box cursor displayed on the viewfinder screen within the effective resolution area.

e; H-POSI (horizontal position) control Adjust the horizontal position of the box cursor displayed on the viewfinder screen within the effective resolution area

ea VF (viewfinder) connector (D-sub 25-pin) Connect to the viewfinder CAMERA connector.

es INTERCOM 1 and 2 connectors (XLR 5-pin)

•Connects to an XLR 5-pin headset. The INTERCOM 1 connector may be used for communications even when the power to the camera is turned off by the HDCU-900 Camera Control Unit. Installing the BKP- 7913 RTS Intercom System Kit (option) allows the INTERCOM 2 connector to work with an RTS intercom system, and be connected to up to two channel devices.

•These connectors may also be used for monitoring a VTR playback audio signal when the HDC-900 is used as a stand-alone unit.

ed INTERCOM PROD/ENG (intercom producer/ engineer line select) switch

Used to switch intercom channel 1 or 2 between producer and engineer lines.

PROD: Use the producer line.

ENG: Use the engineer line.

ef INTERCOM volume control Adjust the intercom output level.

eg PGM 1/2 (program audio select) switch Used to switch between program audio 1 and 2.

eh PGM (program) volume control

Adjust the program audio output level.

ej MIC (microphone) ON/OFF switch Turn the headset microphone on or off.

HDC-900/950/930 Series Product Information Manual Chapter 7 Location and Function of Parts and Controls 81