Sony 900, 930, 950 manual Filter, Paint control block, White balance control block

7	Notes
	When you change the shutter speed, ECS
	• frequency or S-EVS value in the corresponding
	mode, the menu block display shows it for a
	few seconds.
	• When this unit is in RM Configuration Menu
	mode, the shutter speed, ECS frequency and
	S-EVS value cannot be adjusted.
	b Filter control block
	1	1 2 3 4 5		A B C D E	3
			ND	CC
	2					4
			FILTER

AND (ND filter) indicators

The indicator corresponding to the currently selected ND filter illuminates.

BND (ND filter select) button

Press and illuminate the button when it is not lit (Filter camera control mode) to enable filter selection from this unit. When this button is illuminated, the ND filter cyclically changes in the sequence of 1 t 2 t 3 t 4 t 5 t 1 t

... each time it is pressed.

CCC (color temperature conversion filter) indicators

The indicator that corresponds to the currently

selected CC filter is illuminated.

DCC (color temperature conversion filter select) button

Press and illuminate the button when it is not lit (Filter camera control mode) to enable filter selection from this unit. When this button is illuminated, the CC filter cyclically changes in the sequence of A t B t C t D t E t A t

... each time it is pressed.

Notes

•Once you press any of the filter select buttons, both buttons illuminate. The illumination is switched off when filter selection is made on the camera.

•The choice of filters that can be selected depends on the camera being used. For available filters, refer to the Operation Manual of the camera.

•For a camera with four filters, you can change the function of this button to skip 5 or E and switch from 4 to1 or from D to A using the RM Configuration menu. However, when the connected camera has an automatic filter- detection facility, setting with the RM Configuration menu is not required.

cPaint control block

1 2 3 4

AUTO
KNEE	KNEE	M GAMMA	DETAIL

AAUTO KNEE button (amber illumination)

This button is specified at the factory to turn the auto knee function on and off. Press and illuminate the button to turn the auto knee function on. However, you can use the RM Configuration menu to change the function that is turned on/off with this button

BKNEE control

The control is specified at the factory to adjust the master knee point. However, you can use

the RM Configuration menu to change the function that is adjusted with this control.

CM GAMMA (master gamma) control

The control is specified at the factory to adjust the master gamma. However, you can use the RM Configuration menu to change the function

that is adjusted with this control.

DDETAIL control

The control is specified at the factory to adjust the detail level. However, you can use the RM Configuration menu to change the function that is adjusted with this control.

Note

The adjustment mode of the above three controls is specified at the factory as Relative mode, which can be changed to Absolute mode using the RM Configuration menu. The center click position of each control is the reference position in Relative mode. The adjustment range in Relative mode is also selected using the menu.

dWhite balance control block

1	2 3	4	5
	A	AWB
R WHITE	B	PRE
	B

AWHITE (white balance) controls

Adjusts the R/B white balance. The adjustment mode of these controls is specified at the factory as Relative mode, which can be changed to Absolute mode using the RM Configuration

menu. See ‘Settings on the RM Configuration Menu’.

BA (memory A) button (amber illumination) Press and illuminate the button to obtain the white balance setting stored in memory A of the camera (Memory A mode). When this button is illuminated, adjustments made to the white balance are stored in memory A. Press the

button again to release Memory A mode.

CB (memory B) button (amber illumination) Press and illuminate the button to obtain the

white balance setting stored in memory B of the camera (Memory B mode). When this button is illuminated, adjustments made to the white balance are stored in memory B. Press the button again to release Memory B mode.

DAWB (auto white balance) button (red illumination)

Press to start automatic adjustment of the selected items. The button is illuminated during adjustment and this is turned off when adjustment is complete. If you press the button while it is illuminated, the automatic adjustment

is canceled and the button flashes. To stop it flashing, press the button again.

EPRE (preset) button (amber illumination) Press and illuminate the button to fix the white balance to 3200K (Preset mode). Press the button again to release Preset mode.

Note

In Preset mode, manual adjustment with the WHITE controls and automatic adjustment with the AWB button are both disabled. When the adjustment mode of the WHITE controls is

HDC-900/950/930 Series Product Information Manual Chapter 7 Location and Function of Parts and Controls 128