Sony 950, 930, 900 manual 5HKCU-953 HD Frame Rate Converter Unit, 4HKCU-951 SD Encoder Unit

7	a SD output block (DIF board) 1 SD SDI OUT 1 and
	SD SDI OUT 2 (SD-SDI output 1 and 2)
	connectors (BNC type)

When the system is operating with the field frequency of 59.94/50 Hz, the signals from the video camera may be down-converted to SD-component SDI signals and output from these connectors. The OUT 2 connector can be assigned for a digital monitor output that includes character and marker information.

b PIX OUT (picture monitor output) connector (BNC type)

Used for output of the picture monitor video signal selected using the RCP-700-series Remote Control Panel MONITOR SELECT button or the MSU-700A/ 750 Master Setup Unit PICTURE MONITOR button. (When both the RCP and MSU are in use, this connector functions as the output connector for RCP control.)

c WF OUT (waveform monitor output) connector (BNC type)

Used for output of the video signal for waveform monitoring selected using the RCP-700-series Remote Control Panel’s MONITOR SELECT button or the MSU- 700A/750 Master Setup Unit’s WF MONITOR button. (When both the RCP and MSU are in use, this connector functions as the output connector for RCP control.)

Note

The SC phase of the VBS signal output from connectors 2 and 3 is not locked to the black burst signal supplied to the REFERENCE connector. Use the vector monitor in Internal Sync mode.

bY/G, B-Y/B, and R-Y/R (component video signal output) connectors (BNC type)

Used for output of either Y, B-Y, R-Y component video signals or G, B, R component video signals. The type of signal is selected using switches on the EN board. (Factory setting: G, B, R)

7-4-5HKCU-953 HD Frame Rate Converter Unit

The optional HKCU-953 is to be installed in the slot for the DIF board (SD output block)/internal RC board after moving them to the expansion slot.

Connector panel (SDI board)

FC

HD SDI

OUT 1

HD SDI	1 HD SDI OUT 1 and HD SDI OUT 2
	connectors
OUT 2

FRAME

REF IN

2FRAME REF IN and OUT connectors

OUT

7-4-4HKCU-951 SD Encoder Unit

The optional HKCU-951 is to be installed in the HDCU- 950 expansion slot.

Connector panel (VDA board)

EN

VBS

OUT

1 VBS OUT connector

Y/G

B-Y/B

2 Y/G, B-Y/B, and R-Y/R connectors

R-Y/R

aHD SDI OUT 1 and HD SDI OUT 2 (HD SDI output

1 and 2) connectors (BNC type)

These connectors output the signals from the camera as HD-SDI signals. When the camera is operating in 24PsF mode, frame conversion can be applied to input signals to provide 60i/50i signals from these connectors.

bFRAME REF IN and OUT (frame reference input and output) connectors (BNC type)

The IN connector is used to receive an HD tri-level reference sync signal or SD reference sync signal (black burst signal) for frame sequence lock between camera control units. The signal supplied to the IN connector is output from the OUT connector as-is. When this unit is used as the master unit, the OUT connector can be used as the frame sync pulse output connector for pull down.

Note

All the connectors function when the system is operated at a 59.94-/50-Hz field frequency, but do not operate when the system field frequency is 60 Hz.

aVBS OUT (composite video signal output) connector (BNC type)

Used for output of the video camera signal in analog composite video format. An internal setting enables the SD SDI OUT1 and OUT2 connectors on the DIF board also to be used as analog VBS outputs.

HDC-900/950/930 Series Product Information Manual Chapter 7 Location and Function of Parts and Controls 97