Sony 930, 950, 900 Connector that corresponds to the lit, Button. The output signal from the other

7	When one of these buttons is lit, pressing the
	output signal select buttons has effect only on
	the connector that corresponds to the lit
	button. The output signal from the other
	connector does not change. By lighting both
	the buttons, you can simultaneously select the
	output signal.
	Note
	If you light both the WF and PIX buttons when
	different signals are selected for the WF2
	OUTPUT and PIX2 OUTPUT connectors, the
	output select buttons corresponding to the
	1	2	3

PANEL PARA EXPAND

ACTIVE

signals selected for either of the connectors flash. Press the button for the signal to be output to select it again.

For example, when you light both the WF and PIX buttons with R + B selected for PIX2 OUTPUT and B + G selected for WF2 OUTPUT, the R and G buttons will start flashing, while the B button will remain lit. To output R and G, press the R and G buttons. Each pressed button stops flashing and lights.

kCamera select block

MULTI 4 TALLY 5 6

0 7 0 8 0 9 1 0 1 1 1 2

7

MULTI 4

TALLY 5

6

0 1 0 2 0 3 0 4 0 5 0 6

7

APANEL ACTIVE button

Press and light up this button to permit the cameras selected with the camera select buttons to be controlled from this unit. The IRIS/ MB ACTIVE button also lights up. If you press the button when lit, it goes dark and the

operation panel of this unit is locked.

BPARA (parallel mode) button

Press and light up this button to activate Parallel mode, which enables concurrent operation with another control panel. If you press the button

when lit, it goes dark and the Parallel mode is canceled.

CEXPAND button

Press to select the group to be selected with the camera select buttons. Cameras 1 through 12 can be selected when this button is not lit, and cameras 13 through 24 can be selected when this button is lit.

Note

An appropriate camera command network unit (CNU- 700, etc.) is required to control multiple cameras using the camera select function.

DMULTI indicators

Show the Master/Slave status of the corresponding cameras 1 through 12 (when the EXPAND button is not lit) or 13 through 24 (when the EXPAND button is lit).

The indicator for the camera which is specified as the master for Master/Slave mode lights in green. The indicators for the slave cameras light in orange. They light in red during the auto setup of the corresponding cameras. If an error occurs during the auto setup and the operation is interrupted, they will flash in red.

ETALLY indicators

Show the tally status of the corresponding cameras 1 through 12 (when the EXPAND button is not lit) or 13 through 24 (when the EXPAND button is lit). The corresponding indicator lights in red when a red tally is sent to a camera, and it lights in green when a green tally is sent. When both red and green tally are sent, it lights in orange. When a call signal is

sent to the camera, the indicator rapidly flashes in red.

FActive indicators

Show the control status of the corresponding cameras 1 through 12 (when the EXPAND button is not lit) or 13 through 24 (when the EXPAND button is lit). The indicators for the cameras under control of this unit light in green and the indicators for the cameras under control of another control panel light in orange.

An indicator whose corresponding camera (or camera control unit) is not connected does not light.

An indicator lights in red when an error is detected and the self-diagnostic functions are activated in the corresponding camera or camera control unit.

GCamera select buttons and camera number indicators

Select the cameras to be controlled from this unit. Press and light up the button corresponding to each desired camera. When the EXPAND button is not lit, numbers 1 through 12 are displayed and cameras 1 through 12 are selected. When the EXPAND button is lit, numbers 13 through 24 are displayed and cameras 13 through 24 are selected.

HDC-900/950/930 Series Product Information Manual Chapter 7 Location and Function of Parts and Controls 114