Gpf, HtH | Toshiba VF-nC1 specs

E6581090

■How to use the wizard function

Here are the steps to follow to set parameters, using the wizard function. (When the basic setting wizard (CWH) is set to 1)

	Key operated		LED display	Operation
				Displays the operation frequency (operation stopped).
				(When standard monitor display selection H= is set to
				0 [operation frequency]).
	MON		CWJ	The first basic parameter "History (CWJ)" is displayed.

	▲	▼	CWH	Select the wizard function (CWH) by pressing the △ or ▽
	▲	▼	CWH	key.
				key.
	ENT			Press the ENTER key to confirm your choice. is displayed.

	▲	▼		Switch to purpose-specific wizard by pressing the △ or ▽
	▲	▼		key.
				key.
	ENT			Press the ENTER key to confirm your choice. The first
	ENT		EOQF	parameter in the purpose-specific wizard parameter group is
				displayed. (See Table below)
	▲	▼		After moving to the purpose-specific wizard parameter group,
	▲	▼	＊＊＊＊	change the setting of each parameter by pressing the △ or ▽
				key and the ENTER key.
			GPF	GPF is dialyzed on completion of the setting of the wizard
			GPF	parameter group.
				parameter group.
	MON		Display of
	MON		parameter
			parameter
	MON		↓	Press the MON key to exit the wizard parameter group.
	MON		CWH	Press the MON key to exit the wizard parameter group.

↓By pressing the MON key, you can return to the default

MON	HTH	monitoring mode (display of operation frequency).
	HTH
	↓

If there is anything you do not understand during this operation, press the MON key several times to start over from the step of CWJ display.

JGCF or GPF is affixed respectively to the first or last parameter in each wizard parameter group. Table of parameters that can be changed using the wizard function

4

	Basic setting wizard	Preset-speed setting wizard	Analog input operation	Motor 2 switching operation	Torque UP wizard*
	Basic setting wizard	Preset-speed setting wizard	wizard	wizard	Torque UP wizard*
			wizard	wizard
	EOQF	EOQF	EOQF	H	XN
	HOQF	HOQF	HOQF	H	RV
	CEE	CEE	CEE	H	H
	FGE	FGE	FGE	H	H
	HJ	HJ	HJ	XN	H
	WN	WN	WN	H	H
	XN	H	NN	XD
	H	H	H	H
		H	H	VJT
		H	H	CEE
		H	H	FGE
		H	H	H
		UT		H
		UT		H
		UT		H
		UT		H
		UT		H
		UT
		UT
		H
		H
		H
		H
		H
		H
		H
		H

*This parameter is valid only for VFNC1 (S)-□□□□P□-W type.

D-7

Image 48

Toshiba VF-nC1 instruction manual Gpf, HtH

Contents

Industrial Inverter Safety precautions Limits in purpose General operation Transportation ‚ Installation Wiring Operations When retry function is selected inverter Attach warning labels ― Contents ― 10.1 Contents of the product code Read firstCheck purchased product Name and function of each part Operation keypad panel Front panel Self-up terminal block VFNC1-2001P～2007P VFNC1-2015P～2022P VFNC1S-1007P VFNC1S-2015P～2022P Control circuit terminal block Same type of terminal board is provided for all models Motors Inverters Disposal What to do about leak currentLeakage current from the inverter main unit Effects of leakage current across ground Affects of leakage current across lines Remedies Installation Installation environment Examples of unapplicable chemicals and solvents Resistor How to install Installation location VFNC1S VFNC1 Installing more than one unit in a cabinet Connection Control and main power supply WiringStandard connections Preventing radio noise Standard connection diagram VF-nC1 When using V1/S3 terminal as a logic input terminal H DC reactor ＊ DCL option P0 ＊4 DC reactor＊5 Power supply and motor connections Description of terminalsMain circuit terminals Connections with peripheral equipment Control circuit terminals sink logic common CC VI/S3 Sink logic negative common/source logic positive common OUTFLA FLB Switching the input terminal logic between sink and source Simple operation Setting Simple operation of the VF-nC1Run / stop Frequency RUN Motor starts Motor stops slowdown stop Short F and CC terminals run forward Setting the frequency using the operation panel Hoqf Setting the frequency using external potentiometer Setting the frequency by serial communications Hoqf Setting the frequency using input voltageSetting the frequency using current input 4-20mA Basic VF-nC1 operations How to set parameters Setup parameters How to set a setup parameter KP KV How to set the basic parameters Steps in key entry for basic parameters How to set extended parameters Steps in key entry for extended parameters CWH GPF HTH Press the Enter key to display the setting of the parameter ITW CEE Parameters that cannot be changed while running Returning all parameters to standard default setting Kpkv Selecting an operation mode Command mode selectionFrequency setting mode selection Settings Meter setting and adjustment Function Adjustment scale with meter adjustment HO parameter Adjusting the meter in inverter stop stateFM/OUT Houn Standard default setting Setting acceleration/deceleration time Selecting forward and reverse runs operation panel onlyHT Forward/reverse selection Operation panel CEE Acceleration time 1 s FGE Deceleration time 1 s Parameter setting Maximum frequencyUpper limit and lower limit frequencies HJ Maximum frequency Hz Selecting control mode Base frequencyXN Base frequency 1 Hz XD Setting the electronic thermal Setting of motor electronic thermal protection level 1 VJTExplanation of terms Using a VF motor motor for use with inverter Inverter over load characteristicsSetting the motor electronic thermal protection level 1 VJT Preset speed operation speeds in 15 steps Setting method Run/stopPreset speed frequency setting Motor 150%-overload time limit H Using other speed commands with preset speed command Eoqf Output signal-related parameters Output terminal settingExtended parameters FM/OUT terminal functions selection Parameter for specifying a frequency OFF Parameters related to terminal function selection Setting of contact input terminal function Connection method Switching between control logics Sink/Source selection Jog run Setting of output terminal functions Setting of switching terminals Basic parameters40MCHG OFF Analog signals for frequency setting Setting frequency command characteristics Adjustment of 0~10Vdc voltage input Adjustment of 4~20mAdc current input 0 voltage input Starting frequency Starting frequency setting Hz Operation frequency DC braking Preset speed operation frequencies 8 to ～ H Preset speed operation frequencies 8 to 15 HzPWM carrier frequency Jump frequency Hz Jump width Hz Trip-less intensification During restart operation, the message TVT is displayed Start of motor during coasting Motor speed search function Application to a crane or hoist Inverter, motor and machine ・QEC ・QEN・GRJQ ・GTT Setting the PI control parameter Performing PI controlExternal connection Types of PI control interfaces Adjusting the PI control gain level Adjusting an analog command voltage Improving torque and speed characteristics Optimizing control characteristics 2 switching frequency Switching between acceleration and deceleration Acceleration/deceleration Current stall setting Stall prevention level Protection functions External trip stop by means of a terminal Emergency stop by means of the operation panel ①Press the Stop key Gqhh will blink Function Undervoltage trip Under voltage trip selection FM/OUT terminal selection 1 12 OT over-torque detection Setting methods Canceling the settingOperation panel parameters Analog input disconnection detection Communication function common serial Changing the standard monitoring item Selection of monitor display selection 16.1 Using RS232C/RS485 conversion units Setting up the communications functionData transmission specifications Communications parameters Common serial options Free notes Free notes Setting the operation frequency Variety of operation RSS4 Setting the operation mode Status monitor mode Setting procedure eg. operation at 60HzMonitoring the operation status Key to change items displayed in the status monitor mode Display of trip information Example of call-up of trip information ⇔ Taking measures to satisfy the CE / UL / CSA Compliance with CE MarkingAbstract EMC directive 89/336/EEC 【Ex. Countermeasure main circuit wiring】 Compliance with EMC directive Model, noise filter inside Models without EMI filters EMFA2006ZEMFA2015Z EMFAS2011Z 【Operating with external signals】【Accessories for countermeasure】【Apply if needed】 Compliance with Installation Compliance with UL Standard and CSA StandardCompliance with Low voltage directive Compliance with Connection Motor thermal protection AIC Selection of wiring materials and devices Peripheral devices Selection of wiring devices THR Installation of a magnetic contactor Installation of an overload relayMagnetic contactor in the primary circuit Magnetic contactor in the secondary circuit Table of parameters and data 11.1 User parameters11.2 Basic parameters NN－WN VJT QNOUT NNWN Extended parameters Input/output parametersLOW Frequency parameters NN-WN Operation mode parameters Torque boost parameters Acceleration/deceleration time parameters Protection parameters Factory setting parameter Operation panel parametersCommunication parameters Default settings by inverter rating Table of input terminal functions +SS1+AD2 +SS2+AD2+SS3+AD2 +SS4+AD2 Table of output terminal functions Order of precedence of combined functions Specifications Models and their standard specificationsStandard specifications Self-cooling Forced LED External dimensions/weights External dimensions/weightsExternal dimensions Trip causes/warnings and remedies CEE QERFGE QER GRJ GRJ CPU QHHOqhh TVT Uvqr UQUK Restoring the inverter from a trip If the motor does not run while no trip message is displayed YES How to determine the causes of other problems Inspection and maintenance Regular inspectionCheck points Periodical inspection Check items Replacement of expendable parts Standard replacement cycles of principal parts Making a call for servicing Keeping the inverter in storage Warranty Disposal of the inverter 2004-10