Operation panel parameters | Toshiba VF-nC1 guide

E6581090

•Operation panel parameters

		Communication			Minimum setting		Default	User
	Title	Communication	Function	Unit	unit Panel/	Adjustment range	Default	User	Reference
	Title	No.	Function	Unit	unit Panel/	Adjustment range	setting	setting	Reference
		No.			Communication		setting	setting
					Communication
	H	0700	Prohibition of change	-	-	0:Permitted (EOQF,	0		6.15.1
			parameter settings			HOQF cannot be
						changed during
						operation.)
						1:Prohibited
						2:Permitted (EOQF,
						HOQF also can be
						changed during
						operation)
						3:Prohibited (except for
						panel frequency
						setting.)
						4:0 + panel emergency
						stop prohibited
						5:1 + panel emergency
						stop prohibited
						6:2 + panel emergency
						stop prohibited
						7:3 + panel emergency
						stop prohibited
	H	0701	Unit selection	-	-	0:0%, Hz (no change)	0		6.15.2
						1:% to A/V
						2:Free unit selection
						enabled (H)
						3:% to A/V, Free unit
						selection enabled
						(H)
	H	0702	Frequency units	-	0.01/0.01	0.01-200.0	1.00		6.15.2
			selection
	H	0710	Selection of monitor	-	-	0:Operation frequency	0		6.15.3
			display selection			(Hz/free unit)
						1:Frequency
						command (Hz/free
						unit)
						2:Output current (%/A)

•Communication parameters

		Communication			Minimum setting		Default	User
	Title	Communication	Function	Unit	unit Panel/	Adjustment range	Default	User	Reference
	Title	No.	Function	Unit	unit Panel/	Adjustment range	setting	setting	Reference
					Communication
	H	0800	Communication baud	-	-	0:1200bps	3		6.16
			rate			1:2400bps
						2:4800bps
						3:9600bps
						4:19200bps
	H	0801	Parity	-	-	0:NON (non-parity)	1		6.16
						1:EVEN (even parity)
						2:ODD (odd parity)
	H	0802	Inverter number	-	1	0-99	0		6.16
	H	0803	Communication error	s	1/1	0 (Disabled),	0		6.16
			trip time			1 - 100 (s)
	H	0880	Free notes	-	1	0～65535 *	0		6.16

*Adjustment range of the above mention can set by the computer on the network. The operation panel can set to the maximum 9999.

•Factory setting parameter

		Communication			Minimum setting		Default	User
	Title	Communication	Function	Unit	unit Panel/	Adjustment range	Default	User	Reference
	Title	No.	Function	Unit	unit Panel/	Adjustment range	setting	setting	Reference
					Communication
*	H	0990	For factory setting	-	-	-	0		-

*This function is effective after software version V110.

K-7

11

Image 119

Toshiba VF-nC1 instruction manual Operation panel parameters, Communication parameters, Factory setting parameter

Contents

Industrial Inverter Limits in purpose Safety precautions General operation Wiring Transportation ‚ Installation Operations When retry function is selected inverter Attach warning labels ― Contents ― 10.1 Check purchased product Contents of the product codeRead first Operation keypad panel Name and function of each part Front panel Self-up terminal block VFNC1-2001P～2007P VFNC1-2015P～2022P VFNC1S-1007P VFNC1S-2015P～2022P Same type of terminal board is provided for all models Control circuit terminal block Motors Inverters Effects of leakage current across ground DisposalWhat to do about leak current Leakage current from the inverter main unit Remedies Affects of leakage current across lines Examples of unapplicable chemicals and solvents Installation Installation environment Resistor Installation location How to install VFNC1 VFNC1S Installing more than one unit in a cabinet Connection Preventing radio noise Control and main power supplyWiring Standard connections VF-nC1 Standard connection diagram When using V1/S3 terminal as a logic input terminal H DC reactor ＊ DCL option P0 ＊4 DC reactor＊5 Connections with peripheral equipment Power supply and motor connectionsDescription of terminals Main circuit terminals VI/S3 Control circuit terminals sink logic common CC FLB Sink logic negative common/source logic positive commonOUT FLA Switching the input terminal logic between sink and source Simple operation Frequency SettingSimple operation of the VF-nC1 Run / stop Short F and CC terminals run forward RUN Motor starts Motor stops slowdown stop Setting the frequency using external potentiometer Setting the frequency using the operation panel Hoqf Setting the frequency using current input 4-20mA Setting the frequency by serial communications Hoqf Setting the frequency using input voltage Basic VF-nC1 operations Setup parameters How to set parameters KP KV How to set a setup parameter Steps in key entry for basic parameters How to set the basic parameters Steps in key entry for extended parameters How to set extended parameters CWH HTH GPF Press the Enter key to display the setting of the parameter CEE ITW Parameters that cannot be changed while running Kpkv Returning all parameters to standard default setting Settings Selecting an operation modeCommand mode selection Frequency setting mode selection Function Meter setting and adjustment Houn Adjustment scale with meter adjustment HO parameterAdjusting the meter in inverter stop state FM/OUT Standard default setting CEE Acceleration time 1 s FGE Deceleration time 1 s Setting acceleration/deceleration timeSelecting forward and reverse runs operation panel only HT Forward/reverse selection Operation panel HJ Maximum frequency Hz Parameter settingMaximum frequency Upper limit and lower limit frequencies XN Base frequency 1 Hz Selecting control modeBase frequency XD Explanation of terms Setting the electronic thermalSetting of motor electronic thermal protection level 1 VJT Setting the motor electronic thermal protection level 1 VJT Using a VF motor motor for use with inverterInverter over load characteristics Motor 150%-overload time limit H Preset speed operation speeds in 15 stepsSetting method Run/stop Preset speed frequency setting Eoqf Using other speed commands with preset speed command FM/OUT terminal functions selection Output signal-related parametersOutput terminal setting Extended parameters OFF Parameter for specifying a frequency Parameters related to terminal function selection Connection method Setting of contact input terminal function Jog run Switching between control logics Sink/Source selection Setting of output terminal functions OFF Setting of switching terminalsBasic parameters 40MCHG Setting frequency command characteristics Analog signals for frequency setting 0 voltage input Adjustment of 0~10Vdc voltage inputAdjustment of 4~20mAdc current input Operation frequency Starting frequency Starting frequency setting Hz DC braking Jump frequency Hz Jump width Hz Preset speed operation frequencies 8 to ～ H Preset speed operation frequencies 8 to 15 Hz PWM carrier frequency During restart operation, the message TVT is displayed Trip-less intensification Application to a crane or hoist Start of motor during coasting Motor speed search function Inverter, motor and machine ・GTT ・QEC・QEN ・GRJQ Types of PI control interfaces Setting the PI control parameterPerforming PI control External connection Adjusting an analog command voltage Adjusting the PI control gain level Optimizing control characteristics Improving torque and speed characteristics Acceleration/deceleration 2 switching frequencySwitching between acceleration and deceleration Protection functions Current stall setting Stall prevention level External trip stop by means of a terminal ①Press the Stop key Gqhh will blink Emergency stop by means of the operation panel Function FM/OUT terminal selection 1 12 OT over-torque detection Undervoltage trip Under voltage trip selection Analog input disconnection detection Setting methodsCanceling the setting Operation panel parameters Selection of monitor display selection Communication function common serialChanging the standard monitoring item Communications parameters Common serial options 16.1 Using RS232C/RS485 conversion unitsSetting up the communications function Data transmission specifications Free notes Free notes Variety of operation Setting the operation frequency RSS4 Setting the operation mode Monitoring the operation status Status monitor modeSetting procedure eg. operation at 60Hz Key to change items displayed in the status monitor mode Display of trip information Example of call-up of trip information ⇔ EMC directive 89/336/EEC Taking measures to satisfy the CE / UL / CSACompliance with CE Marking Abstract Compliance with EMC directive Model, noise filter inside 【Ex. Countermeasure main circuit wiring】 EMFAS2011Z Models without EMI filtersEMFA2006Z EMFA2015Z 【Operating with external signals】【Apply if needed】【Accessories for countermeasure】 Compliance with Connection Compliance with InstallationCompliance with UL Standard and CSA Standard Compliance with Low voltage directive AIC Motor thermal protection Peripheral devices Selection of wiring materials and devices THR Selection of wiring devices Magnetic contactor in the secondary circuit Installation of a magnetic contactorInstallation of an overload relay Magnetic contactor in the primary circuit NN－WN Table of parameters and data11.1 User parameters 11.2 Basic parameters NNWN VJTQNO UT LOW Extended parametersInput/output parameters NN-WN Frequency parameters Torque boost parameters Operation mode parameters Protection parameters Acceleration/deceleration time parameters Communication parameters Factory setting parameterOperation panel parameters Default settings by inverter rating Table of input terminal functions +SS4+AD2 +SS1+AD2+SS2+AD2 +SS3+AD2 Table of output terminal functions Order of precedence of combined functions Standard specifications SpecificationsModels and their standard specifications Self-cooling Forced LED External dimensions External dimensions/weightsExternal dimensions/weights FGE QER Trip causes/warnings and remediesCEE QER GRJ GRJ TVT CPUQHH Oqhh UK UvqrUQ Restoring the inverter from a trip YES If the motor does not run while no trip message is displayed How to determine the causes of other problems Check points Inspection and maintenanceRegular inspection Check items Periodical inspection Standard replacement cycles of principal parts Replacement of expendable parts Keeping the inverter in storage Making a call for servicing Warranty Disposal of the inverter 2004-10