Yamaha MOTIF6, MOTIF7, MOTIF8, Music Production Synthesizer • Decay, • Detune, • Cutoff, • Attack, • Sustain, • NoteShift, • Resonance, • FEG Depth, ●[F3] Part Output Select, ●[F4]-[SF1]Part Tone Tune

●[F3] Part Output Select

From this display you can set certain output parameters for the selected part.

• InsEF (Insertion Effect)

This shows whether the Insertion effect is applied or not for each part. This is for display purposes only and cannot be set here. To set this, see “EF PART” (Effect Part) on page 40.

• OutputSel (Output Select)

Determines the specific output(s) for the individual part. You can assign each individual part’s voice to be output from a specific hardware output jack on the rear panel. By installing the optional AIEB2 board, you can expand the number of assignable outputs.

❏ Settings See below.

LCD	Output jacks	Stereo/
		Mono
L&R	OUTPUT L and R	Stereo
asL&R	ASSIGNABLE OUTPUT L and R	Stereo
		Stereo
as1&2	ASSIGNABLE OUTPUT 1 and 2 on the AIEB2	1 : L	*
		2 : R
		Stereo
as3&4	ASSIGNABLE OUTPUT 3 and 4 on the AIEB2	3 : L	*
		4 : R
		Stereo
as5&6	ASSIGNABLE OUTPUT 5 and 6 on the AIEB2	5 : L	*
		6: R
asL	ASSIGNABLE OUTPUT L	Mono
asR	ASSIGNABLE OUTPUT R	Mono
as1	ASSIGNABLE OUTPUT 1 on the AIEB2	Mono	*
as2	ASSIGNABLE OUTPUT 2 on the AIEB2	Mono	*
as3	ASSIGNABLE OUTPUT 3 on the AIEB2	Mono	*
as4	ASSIGNABLE OUTPUT 4 on the AIEB2	Mono	*
as5	ASSIGNABLE OUTPUT 5 on the AIEB2	Mono	*
as6	ASSIGNABLE OUTPUT 6 on the AIEB2	Mono	*
	This setting is for Drum voice parts. When this is
drum	selected, the output destination settings for each	Mono
	Drum key (made in Drum Key Oscillator Output,
	page 149) are enabled.

*Available only when the optional AIEB2 board has been installed.

●[F4]-[SF1] Part Tone Tune• NoteShift

Determines the pitch (key transpose) setting for each part in semitones.

❏ Settings -24~+24

Performance Edit mode

• Detune

Determines the fine tuning for each part. ❏ Settings -12.8Hz ~+12.7Hz

● [F4]-[SF2] Part Tone Filter

Basic Structure (page 46)

From this display you can set various Filter related settings, to change the tonal qualities of the selected part’s voice.

• Cutoff

Determines the cutoff frequency for each part.

This parameter is available for the LPF when the filter used by the part is a combination type of LPF and HPF.

❏ Settings -64 ~ 0 ~ +63

• Resonance

Determines the amount of filter resonance or emphasis of the Cutoff Frequency for each part.

❏ Settings -64 ~ 0 ~ +63

• FEG Depth
Determines the Filter Envelope Generator depth (amount
of Cuttoff frequency) for each part.
	mode
❏ Settings 0 ~ 127
	Performance
n The FEG Depth setting is not available for the
Plug-in parts.
● [F4]-[SF3] Part Tone FEG	Reference
Generator) parameters for each part. The following
Basic Structure (page 47)
From this display you can set the FEG (Filter Envelope
parameters offset the same parameters in the Voice
(Element) Edit mode (page 142).

• Attack

Determines the FEG Attack Time for each part. ❏ Settings -64 ~ 0 ~ +63

• Decay

Determines the FEG Decay Time for each part. ❏ Settings -64 ~ 0 ~ +63

• Sustain

Determines the FEG Sustain Level for each part. ❏ Settings -64 ~ 0 ~ +63

MOTIF Reference 173