Choose allocation window appears as shown below | Denso RC5 instruction

"STEP 3

"STEP 4

"STEP 5 "STEP 6

The Choose allocation window appears as shown below.

NOTE: If your robot controller has a built-in DeviceNet master, the Select Port Assignment window will appear instead of the Select I/O Assignment Mode window. Refer to the DeviceNet Master Unit user's manual, Chapter 3, "I/O Assignment."

Using the jog dial or cursor keys, select the desired assignment mode. Then press OK.

The following system message appears.

Press OK.

The screen returns to the Auxiliary Functions (I/O) window.

Turn the controller power OFF.

Turn the controller power ON again.

The I/O assignment mode is switched.

16

Image 36

Denso RC5 manual Choose allocation window appears as shown below, Following system message appears

Contents

Robot Page Preface Robot models covered by this manual How the documentation set is organized Interface Manual this book Describes I/O cables and wiring Iii How this book is organizedPage Safety Precautions Should not be installed in any environment where Structure. Therefore, when using the robot controller in anRobot and peripheral equipment should be installed so that Sufficient service space is maintained for safe teaching Safety Precautions Page No robot modification allowed Cleaning of tools Lighting Refer to the Installation & Maintenance Guide Or maintenance inspections, set working regulations for Operating procedures required to run the robotRobot speed when performing teaching Signaling methods to be used when more than one worker Safety Precautions Page Management of floppy disks Page Contents Dedicated to Standard Mode 100 Index Controller Model Name on Nameplate Coding of Controller Model NamePosition Code Denotes Coding Sample How to identify your robot system as Type a Deadman switches are located as shown belowSymbol denoting Type a Internal Auto Limited Mode External Auto Limited ModeSetting the parameter Names of the Robot Controller Components FrontLeft side Right side Names of Robot Controller Components VM-D/HM-E series For robot series except VM-D/HM-E Connector Marking Name Robot Controller Specifications Table below lists the robot controller specificationsRobot Controller Specifications Page Outer Dimensions Outer dimensions of the robot controller are shown below Location of IPM boards Series Location Models Controller System Configuration Internal Circuits of the Controller Typical configuration Typical Robot System Configurations Robot System Configuration System Configuration Example Standard Mode and Compatible Mode Switching between Modes I/O Monitor window appears Auxiliary Functions I/O window appears as shown below I/O assignment mode is switched Choose allocation window appears as shown belowFollowing system message appears Screen returns to the Auxiliary Functions I/O window Computer SectionGUIDE, , Section Click on the DIO Manager button in the System Manager Hardware settings will appear Options window will appear as shown below Options window closes Connect button appears in a pressed state Update the data Transfer Environment Table window appears I/O assignment mode is switched Types and General Information about I/O Signals Standard Mode Compatible Mode Compatibility with conventional VS series robotsControlled by user program Type No. Function Points Using User I/O Signals common to both modes User Input Commands1 I/O Type Variable Declaration 2 I/O Type Global Variables User Output Commands SET Command System I/O Signals Standard Mode Types and Functions of System Output Signals Standard Mode Usage of System Output Signals Standard Mode Robot Initialization Complete Output Auto Mode Output Auto mode OutputOn condition OFF conditions External Mode Output No.7 of connector CN10External Mode Output Terminal number No.4 of connector CN10 Servo on OutputServo on Output Signal will be turned OFF with Stop ALL Programs Robot-in-operation Output Normal CPU Output Normal CPU Output Robot Failure Output Robot Failure Output Robot Warning Output Robot Warning Output Dead Battery Warning Output Dead Battery Warning Output SS mode Output This signal comes on when the SS mode is selectedContinue Start Permitted Output No of connector CN10 Emergency stop + Emergency Stop Output from a contactContact Types and Functions of System Input Signals Standard Mode Usage of System Input Signals Standard Mode Enable Auto InputNo of connector CN8 Relationship Between Enable Auto Input and Selectable Mode Robot Stop Input Timing of the input No.5 of connector CN8 Step Stop SignalStep Stop All Tasks Input Terminal Instantaneous Stop All Tasks Input Minimum Instantaneous Stop Pulse Width Terminal number No.9 of connector CN8 Interrupt Skip InputSee the Programmers Manual I, , 12.3 Interrupt ON/OFF Input Conditions and Operation of Interrupt Skip Example of Operation When an Interrupt Skip is Input Wrong General Information about Commands Table below shows the I/O commands functionsCommand Functions Commands to be executed are processed as shown below Outline of I/O Command ProcessingPage Using Each Signal Line Terminal numbers Strobe Signal Input Command Processing Complete Output No of connector CN10 Nos to 32 of connector CN10 Status Area 3 I/O Commands Details List of I/O Commands Table below lists I/O commandsList of I/O Commands Program Operation Command FormatDescription Page Page External Speed and Acceleration Setting Error Read Example of Error Number OutputHexadecimal codes Refer to the figure given below Type I Variable Write Type I Variable Read Mode Switching Page This command clears a robot failure that has been caused Clear Robot Failure 3.9 I/O Write 3.10 I/O Read Example of Using System I/O Signals in Standard Mode Equipment setup exampleExample of Equipment Setup Using a Robot Outline of procedure Start and stop procedure, and system I/O signals Start and Stop Procedure and System I/O Signals-1 On following From preceding END System I/O Signals Compatible Mode Usage of System Output Signals in the Compatible Mode Robot Power on Complete Teach Check ⋅ MOTORu OFv F Signal outputs to the external device that CAL is completed CAL Complete OutputCAL Complete Output External Mode Output Teaching Output Teaching Output Program Start Reset Output Program Start Reset Output on Condition Program will be turned OFF with Stop ALL Programs Single-Cycle End Output Single-Cycle End Output Normal CPU Output Operated. Cancelu ƒv L ‘ € ì Robot Warning Output Power on Error No. Output No.17 to No.28 of connector CN10Signal will be output when an error occurs Clear conditions Continue Start Permitted Output Emergency Stop Output from a contact Types and Functions of System Input Signals Compatible Mode Usage of System Input Signals in Compatible Mode OFF Motor power on input Operation Preparation Start Input Example of Operation Preparation Start Signal Timing Chart No.11 to No.18 of connector CN8 Program No. Select SignalProgram No. Select Input Example of Program No. Select Signals Example of Program No. Select Signal Sequence Circuit Program Start Input Program Start Operation-1 Program Start Operation-2 Program Start Operation-3 Example of program start signal rise on and fall OFF timing Example of Program Start Signal Rise Timing Example of Program Start Signal Fall Timing-1 Example of Program Start Signal Fall Timing-2 Program Start Signal Rise Output Signal Timing Program Reset Input Input Conditions and Operation of Program Reset Signal When issued with the Operation Preparation Start Input timing 101 102 Clear Robot Failure Input 103 Refer to the Programmers Manual I 104 Example of Operation When an Interrupt Skip Signal is Input Continue Start Input Example of Using System I/O Signals in Compatible Mode 106 Start and stop procedure and system I/O signals On the next 108 Signal 109Operation Preparation Start Input Connector Pin Assignment NPN type Connector Pin Assignment Common to Both Modes NPN type110 111 CN1 Pin Assignment Terminal No Name Connector Pin Assignment in Standard Mode Output CN10 User-/System-output connector standard mode112 Input CN8 User-/System-input connector standard mode 113 Connector Pin Assignment in Compatible Mode Output CN10 User-/System-output connector compatible mode114 Input CN8 User-/System-input connector compatible mode 115 Robot Controller I/O Circuits NPN type User-Input, System-Input and Hand-Input Circuits NPN type116 117 118 Robot Stop and Enable Auto Input Circuits Robot Stop and Enable Auto Input Circuits 120 121 122 123 Example of Circuit with Lamp NPN type When the internal power source is used Emergency Stop CircuitStandard type 124 Dual emergency stop type 125Emergency Stop Circuit Dual emergency stop type 5 I/O Power Connector NPN type 126 127 Wiring Notes for Robot Controller I/O Connectors NPN Type 128Checking Example 129 Name Meaning Check Number Point Connector Pin Assignment PNP type Connector Pin Assignment Common to Both Modes PNP type130 O Power CN7 Power connector for I/O common to both modes 131 Terminal Number Name Port Wire Color Port Wire number color 132 Input CN8 User-/System-input connector standard mode 133 134 135 #26, #2 and #27,…#25 and #50 Robot Controller I/O Circuits PNP type User-Input, System-Input and Hand-Input Circuits PNP type136 137 138 Robot Stop and Enable Auto Input Circuits 140 141 142 143 Example of Circuit with Lamp PNP type 144 145 5 I/O Power Connector PNP type 146 147 Wiring Notes for Robot Controller I/O Connectors PNP Type 148 149 Multi-core Cables with Connectors 150Cables Optional items Modifying the Shielding Wire Example 151 Wiring of Primary Power Source Robot Controller Power Supply Specifications Index Servo on Output First Edition Second Edition June