Command Processing Complete Output | Denso RC5 manual

[ 3 ] Command Processing Complete (Output)

(1)Function

The signal outputs to the external device that I/O command processing is completed.

(2)Terminal number

No. 15 of connector CN10.

(3)Usage

The signal is used to confirm that I/O command processing is complete, or as a timing signal for obtaining the result of I/O command processing.

(4)ON conditions

•The signal will be turned ON upon completion of processing the I/O command given and determination of outputting the status area.

‚If an error occurs as a result of executing an I/O command, the result will not be output to the status area, but the robot failure signal and the command processing complete signal will be turned simultaneously ON.

(5)OFF conditions

• The signal will be turned OFF when the strobe signal is turned OFF.

‚If the strobe signal is turned OFF, before command processing is completed, the command processing complete signal will be output and then turned OFF within 100 msec.

50

Image 70

Denso RC5 manual Command Processing Complete Output, No of connector CN10

Contents

Robot Page Preface Robot models covered by this manual How the documentation set is organized Interface Manual this book Describes I/O cables and wiring Iii How this book is organizedPage Safety Precautions Robot and peripheral equipment should be installed so that Should not be installed in any environment whereStructure. Therefore, when using the robot controller in an Sufficient service space is maintained for safe teaching Safety Precautions Page No robot modification allowed Cleaning of tools Lighting Refer to the Installation & Maintenance Guide Robot speed when performing teaching Or maintenance inspections, set working regulations forOperating procedures required to run the robot Signaling methods to be used when more than one worker Safety Precautions Page Management of floppy disks Page Contents Dedicated to Standard Mode 100 Index Coding of Controller Model Name Controller Model Name on NameplatePosition Code Denotes Coding Sample Deadman switches are located as shown below How to identify your robot system as Type aSymbol denoting Type a External Auto Limited Mode Internal Auto Limited ModeSetting the parameter Left side Right side Names of the Robot Controller ComponentsFront Names of Robot Controller Components VM-D/HM-E series For robot series except VM-D/HM-E Connector Marking Name Table below lists the robot controller specifications Robot Controller SpecificationsRobot Controller Specifications Page Outer Dimensions Outer dimensions of the robot controller are shown below Location of IPM boards Series Location Models Controller System Configuration Internal Circuits of the Controller Typical configuration Typical Robot System Configurations Robot System Configuration System Configuration Example Standard Mode and Compatible Mode Switching between Modes I/O Monitor window appears Auxiliary Functions I/O window appears as shown below Following system message appears I/O assignment mode is switchedChoose allocation window appears as shown below Screen returns to the Auxiliary Functions I/O window GUIDE, , Section ComputerSection Click on the DIO Manager button in the System Manager Hardware settings will appear Options window will appear as shown below Options window closes Connect button appears in a pressed state Update the data Transfer Environment Table window appears I/O assignment mode is switched Types and General Information about I/O Signals Standard Mode Compatibility with conventional VS series robots Compatible ModeControlled by user program Type No. Function Points 1 I/O Type Variable Declaration Using User I/O Signals common to both modesUser Input Commands 2 I/O Type Global Variables User Output Commands SET Command System I/O Signals Standard Mode Types and Functions of System Output Signals Standard Mode Usage of System Output Signals Standard Mode Robot Initialization Complete Output On condition Auto Mode OutputAuto mode Output OFF conditions External Mode Output External Mode OutputNo.7 of connector CN10 Terminal number Servo on Output No.4 of connector CN10Servo on Output Signal will be turned OFF with Stop ALL Programs Robot-in-operation Output Normal CPU Output Normal CPU Output Robot Failure Output Robot Failure Output Robot Warning Output Robot Warning Output Dead Battery Warning Output Dead Battery Warning Output This signal comes on when the SS mode is selected SS mode OutputContinue Start Permitted Output Emergency Stop Output from a contact No of connector CN10 Emergency stop +Contact Types and Functions of System Input Signals Standard Mode No of connector CN8 Usage of System Input Signals Standard ModeEnable Auto Input Relationship Between Enable Auto Input and Selectable Mode Robot Stop Input Timing of the input Step Stop All Tasks Input No.5 of connector CN8Step Stop Signal Terminal Instantaneous Stop All Tasks Input Minimum Instantaneous Stop Pulse Width See the Programmers Manual I, , 12.3 Interrupt ON/OFF Terminal number No.9 of connector CN8Interrupt Skip Input Input Conditions and Operation of Interrupt Skip Example of Operation When an Interrupt Skip is Input Wrong Table below shows the I/O commands functions General Information about CommandsCommand Functions Commands to be executed are processed as shown below Outline of I/O Command ProcessingPage Using Each Signal Line Terminal numbers Strobe Signal Input Command Processing Complete Output No of connector CN10 Nos to 32 of connector CN10 Status Area Table below lists I/O commands 3 I/O Commands Details List of I/O CommandsList of I/O Commands Format Program Operation CommandDescription Page Page External Speed and Acceleration Setting Hexadecimal codes Error ReadExample of Error Number Output Refer to the figure given below Type I Variable Write Type I Variable Read Mode Switching Page This command clears a robot failure that has been caused Clear Robot Failure 3.9 I/O Write 3.10 I/O Read Equipment setup example Example of Using System I/O Signals in Standard ModeExample of Equipment Setup Using a Robot Outline of procedure Start and stop procedure, and system I/O signals Start and Stop Procedure and System I/O Signals-1 On following From preceding END System I/O Signals Compatible Mode Usage of System Output Signals in the Compatible Mode Robot Power on Complete Teach Check ⋅ MOTORu OFv F CAL Complete Output Signal outputs to the external device that CAL is completedCAL Complete Output External Mode Output Teaching Output Teaching Output Program Start Reset Output Program Start Reset Output on Condition Program will be turned OFF with Stop ALL Programs Single-Cycle End Output Single-Cycle End Output Normal CPU Output Operated. Cancelu ƒv L ‘ € ì Robot Warning Output Power on Signal will be output when an error occurs Error No. OutputNo.17 to No.28 of connector CN10 Clear conditions Continue Start Permitted Output Emergency Stop Output from a contact Types and Functions of System Input Signals Compatible Mode Usage of System Input Signals in Compatible Mode OFF Motor power on input Operation Preparation Start Input Example of Operation Preparation Start Signal Timing Chart Program No. Select Signal No.11 to No.18 of connector CN8Program No. Select Input Example of Program No. Select Signals Example of Program No. Select Signal Sequence Circuit Program Start Input Program Start Operation-1 Program Start Operation-2 Program Start Operation-3 Example of program start signal rise on and fall OFF timing Example of Program Start Signal Rise Timing Example of Program Start Signal Fall Timing-1 Example of Program Start Signal Fall Timing-2 Program Start Signal Rise Output Signal Timing Program Reset Input Input Conditions and Operation of Program Reset Signal When issued with the Operation Preparation Start Input timing 101 102 Clear Robot Failure Input 103 Refer to the Programmers Manual I 104 Example of Operation When an Interrupt Skip Signal is Input Continue Start Input Example of Using System I/O Signals in Compatible Mode 106 Start and stop procedure and system I/O signals On the next 108 109 SignalOperation Preparation Start Input Connector Pin Assignment Common to Both Modes NPN type Connector Pin Assignment NPN type110 111 CN1 Pin Assignment Terminal No Name Output CN10 User-/System-output connector standard mode Connector Pin Assignment in Standard Mode112 Input CN8 User-/System-input connector standard mode 113 Output CN10 User-/System-output connector compatible mode Connector Pin Assignment in Compatible Mode114 Input CN8 User-/System-input connector compatible mode 115 User-Input, System-Input and Hand-Input Circuits NPN type Robot Controller I/O Circuits NPN type116 117 118 Robot Stop and Enable Auto Input Circuits Robot Stop and Enable Auto Input Circuits 120 121 122 123 Example of Circuit with Lamp NPN type Standard type When the internal power source is usedEmergency Stop Circuit 124 125 Dual emergency stop typeEmergency Stop Circuit Dual emergency stop type 5 I/O Power Connector NPN type 126 127 128 Wiring Notes for Robot Controller I/O Connectors NPN TypeChecking Example 129 Name Meaning Check Number Point Connector Pin Assignment Common to Both Modes PNP type Connector Pin Assignment PNP type130 O Power CN7 Power connector for I/O common to both modes 131 Terminal Number Name Port Wire Color Port Wire number color 132 Input CN8 User-/System-input connector standard mode 133 134 135 #26, #2 and #27,…#25 and #50 User-Input, System-Input and Hand-Input Circuits PNP type Robot Controller I/O Circuits PNP type136 137 138 Robot Stop and Enable Auto Input Circuits 140 141 142 143 Example of Circuit with Lamp PNP type 144 145 5 I/O Power Connector PNP type 146 147 Wiring Notes for Robot Controller I/O Connectors PNP Type 148 149 150 Multi-core Cables with ConnectorsCables Optional items Modifying the Shielding Wire Example 151 Wiring of Primary Power Source Robot Controller Power Supply Specifications Index Servo on Output First Edition Second Edition June