Specifications, Regulatory Compliances | FARGO electronic HDP700

FARGO Electronics Inc.

Section

1

Specifications

Regulatory Compliances

FCC

The Card Printer complies with the requirements in Part 15 of the FCC rules for a Class B digital device. These requirements are designed to provide reasonable protection against harmful interference in a residential installation. If, however, operation of this equipment in a residential area causes unacceptable interference to radio and TV reception, the operator is required to take whatever steps are necessary to correct the interference.

UL

The Card Printer is listed under UL 1950 INFORMATION TECHNOLOGY EQUIPMENT.

File Number

E145118, Volume 1, Section 15.

CSA

The printer manufacturer has been authorized by UL to represent the Card Printer as CSA Certified under CSA Standard 22.2.

File Number

E145118.

TÜV-GS

The Card Printer has been tested and complies with IEC950 and bears the TÜV-GS mark.

License Number

S9971826.

ITS-EMC

The Card Printer has been tested and complies with EN55022 Class B: 1995 and EN70082-1: 1997 standards for EMI emissions.

License Number

J99032510.

Based on the above testing, the printer manufacturer certifies that the Card Printer complies with all current EMC directives of the European Community and has placed the CE mark on the Card Printer.

HDP700 Series Card Printer

1-1

Image 11

FARGO electronic HDP700 manual Specifications, Regulatory Compliances

Contents

Page Page Fargo Electronics, Incorporated Page Table of Contents Image Transfer Tab Removing the Covers Packing Your HDP700 Card Printer LCD ON-LINE Menu Navigation Page Regulatory Compliances Specifications Agency Listings Technical Specifications Weight Operating TemperatureHDP Film Storage Temperature Dimensions HDP700 Series Card Printer Contacting Fargo Technical Support General Troubleshooting LCD Messages LCD Display Messages Message Cause / Solution SmartGuard Error / Status Messages Interference from external device Communication ErrorsParallel port mode set incorrectly System does not meet requirements Inadequate hard drive space Printer is unable to align flipper Card Feed ErrorsCard is stalling on or at the feed rollers Card jamming on the Flipper Table Encoding Errors HDP700 Series Card Printer Printing Process Errors Printer Open Printhead Temp Card Jam Transfer Process ErrorsTransfer Film Drive Error Laminator Cooling Error Transfer Lift Temperature Timeout Output Errors Card Surface Debris Diagnosing Image ProblemsPixel Failure Incorrect Image Darkness Symptom Printed cards are too dark or too light Ribbon Wrinkle Incomplete Resin Printing Excessive Resin Printing HDP Film Wrinkle Symptom HDP Film is creased or wrinkled on the printed card Incomplete Transfer Image Placement Image Washout on Film Poor Image Quality Image Skewed on the Card Registration problem Printer Adjustments Refer To Drawing Tools Needed Fine-Tuning the Card Separator Adjustment Assembly D840995 Tape Adhesion Test Selecting The Appropriate HDP Printer Driver Settings Fail Color Matching Printer Driver OptionsDevice Options Tab Ribbon Type Print Back Side Only HDP720 only Disable PrintingPrint Both Sides HDP720 only Split 1 Set of Ribbon Panels HDP720 only Image Color Tab Image Position Image Transfer Tab Flattener Temperature Transfer Dwell Time and Temperature Panel Resin Tab HDP700 Series Card Printer Defining an Area HDP700 Series Card Printer HDP700 Series Card Printer Overview Encoding Mode / Coercivity / Magnetic Track SelectionMagnetic Encoding Tab ISO Track Locations Magnetic Track OptionsVerification Shift Data Left Sample String Sending Track Information Ascii Chart Card Type Card TabCard Size Cleaning the Printer Clean the Cleaning Rollers Clean the Inside of the Printer HDP700 Series Card Printer Parts Replacement HDP Lamination Board Cable Connections Rear Transfer Cover Removing the CoversPrint Station Cover Front Transfer Cover Card Input Hopper Cover Base Module Cover Back Cover Card Output Hopper Cover Replacing the Control Panel Assembly Components Printhead D840854 Replacing the Printhead Assembly ComponentsFan Assembly 840134 Ribbon Deflector D840638 Head Force Spring 2 Headlift Drive O-Ring Refer To Drawing Tools Needed Replacing the Print Station ComponentsRings 140212 Encoder Wheel Ribbon Sensor Board Assembly 140407 Ribbon Supply Motor Assembly D840980 Ribbon Sensor Array Assembly Headlift Motor Assembly 840131 Ribbon Take-Up Motor Assembly D840980 Headlift Sensor Assembly D840983 Ribbon Supply Encoder Sensor Assembly D840982 Encoder Wheel 2 Replacing the Transfer Station ComponentsFilm Drive O-Rings Lamination Supply Encoder Sensor Assembly Stepper Motor Assembly 840123 Lower Film Sensor Assembly Lamination Take-Up Encoder Sensor Assembly Print Platen Roller Upper Film Sensor Assembly D841023 Ribbon Drive Hub 2 Transfer Ribbon Peel Off Bar Assembly D840698 Transfer Station Assembly Refer to drawing Tools Required Lamination Assembly Transfer Lift Motor Transfer Lift Switch HDP700 Series Card Printer Drive Belt Card Feed Roller to Card Feed Roller Replacing the Belt Driven Base Module ComponentsDrive Belt Platen Roller to Card Feed Roller Front Stepper Motor Assembly Pinch Roller Spring Plate-Front -- 2 Compound Grooved Pulley Drive Belt-Tensioner to Platen Roller F000003 Pinch Roller Spring Plate-Back -- 2 Drive Pulley Front -- 3 D850190 Drive Belt-Stepper Motor to Tensioner F000004 Drive Pulley Back -- 2 D850190 Base Module Belt F000018 HDP700 Series Card Printer Drive Belt Platen Roller to Card Feed Roller Replacing the Gear Driven Base Module Components Stepper Motor Assembly Pinch Roller Spring Plate-Front Output Side Pinch Roller Spring Plate-Front Input Side Pinch Roller Spring Plate-Back Output Side 840354 Pinch Roller Spring Plate-Back Input Side 840354 Gear Card Transport --2 Compound Gear D841032 HDP700 Series Card Printer Replacing the Card Input Hopper Components Flipper Table Sensor Board AssemblyCard Low Sensor Board Assembly 140407 Card Feed Belt Cleaning Roller Drive Idler Gear 760401 Card Feed Gear 3 Encoding Feed Motor Assembly 840100 Flipper Table Position Stepper Motor 840124 Cleaning Roller AssemblyCard Feed Motor Assembly Clutch Spring 840285 Card Sensor Assembly-Flipper Table D840624 Magnetic Encoder Head 840104 Card Feed Sensor D840625 Encoder Card Sensor Power Cord Receptacle 130067 Replacing the Power Assembly ComponentsPower Switch Lamination Board Main Print Board A000030 Refer to Drawing D840590 Tools Needed Power SupplyReplacing the Output Stacker Components Output Stacker D840590 Stacker Lift Motor 840130 Stacker Full SensorPage Page Belt Driven Base Module Components Gear Driven Base Module Components Page Page Page Page Page Page Page Page Page HDP700 Series Card Printer Packing your HDP700 Card Printer HDP700 Series Card Printer Board Errors Sensor Testing Entering the LCD Menu and Selecting an Option HDP700 Series Card Printer Gray/Align Ymck for HDP710 Gray/Align YMC/K for HDP720 Print Test Image Select Transfer EOF Setup Printer Aligning the Print Offset Adjusting the Transfer Tension Setting the Transfer TOF Setting the Transfer EOF Adjusting the Transfer Temperature Adjusting the Film DriveAdjusting the Ribbon Tension Adjusting the Ribbon Drive Changing the Encoder Settings Setting the Flattener TemperatureSetting the Printhead Resistance Adjusting the Image Darkness Select MENU, Setup Printer, and Magnetic TOF Setting the Magnetic TOF Show Card Count Show Error CountAdjusting the Flipper Offset System Upgrade Firmware Upgrade Downloading Firmware Updates Firmware Updater Application Program Updating the Printers Firmware To update the Main Firmware Figure A-3 To update the LCD Firmware Figure A-5