HP 5100LE manual Unable to, Store JOB, USE Type, Size INSTEAD?, Reinitialize, Xx.Yy, Printer Error

Table 32. Printer messages

Message	Explanation or recommended action
UNABLE TO	A job cannot be stored on the printer because of memory limitations or the file
STORE JOB	system configuration.
USE [TYPE]	If the requested paper size or type is not available, the printer asks if it should use
[SIZE] INSTEAD?	another paper size or type instead.
	Press [-VALUE+]to scroll through the available types and sizes. Press [SELECT] to
	accept an alternative type or size.
WAIT FOR PRINTER TO The RAM disk setting has been changed at the printer control panel. This change
REINITIALIZE	will not take effect until the printer reinitializes.
XX.YY	A printer error has occurred that can be cleared by pressing [GO] in the printer
PRINTER ERROR	control panel.
PRESS GO TO
CONTINUE
13.1 PAPER JAM	The event log message for a paper-delay jam at the paper feed area is 13.1.
or	The event log message for a paper-stopped jam at the paper feed area is 13.2.
	1. Make sure that paper trays are loaded correctly so that paper can feed from the
13.2 PAPER JAM
	tray.
	2. Check the input area for obstructions, such as print media in the path, damage
	to the registration assembly, or an out-of-place transfer roller.
	3. Check PS402 and PS403 for correct operation. Replace any defective sensors
	or flags. For the locations of sensors, see page 236.
13.5 PAPER JAM	The event log message for a paper-delay jam at the fuser is 13.5.
or	The event log message for a paper-stopped jam at the fuser is 13.6.
	1. Check the transfer roller and the small media belt to ensure that they are
13.6 PAPER JAM
	operating and can feed media.
	2. Check the paper path for obstructions at the transfer roller and toner cartridge,
	at the paper-feed guide, and at the fuser.
	3. Check PS1306 for correct operation. Replace any defective sensors or flags.
	For the locations of sensors, see page 236.
13.10 PAPER JAM	The event log message for a paper-delay jam in the duplexer is 13.10.
	1. Check the duplexer and the rear area of the printer for obstructions or damage.
	2. Check PS1701 and PS1703 in the duplexer for correct operation. Replace the
	duplexer if a sensor is defective.
13.20 PAPER JAM	The event log message for a paper-stopped jam in the paper path is 13.20.
or	The event log message for a top door opened while printing jam is 13.21.
	1. Check the entire paper path for obstructions such as print media in the path,
13.21 PAPER JAM
	registration area, transfer area, paper feed, and fuser.
	2. Check that all of the assemblies are seated and that all of the doors are closed.
	3. Check all of the sensors and flags in the paper path (see page 236).
20 INSUFFICIENT	The printer received more data than can fit in its available memory. You might have
MEMORY	tried to transfer too many macros, soft fonts, or complex graphics.
alternates with	Press [GO] to print the transferred data (some data might be lost), then simplify
PRESS GO TO	the print job or install additional memory (see page 107).
CONTINUE

21PAGE TOO COMPLEX The data (dense text, rules, raster or vector graphics) sent to the printer was too

alternates with	complex.
	Press [GO] to print the transferred data. (Some data might be lost.)
PRESS GO TO
CONTINUE	To print the job without losing data, from the configuration menu in the printer
	control panel, set PAGE PROTECT=ON and print the job. Leaving PAGE
	PROTECT=ON might degrade performance.
	If this message appears often, simplify the print job or leave PAGE PROTECT=ON.

196 Troubleshooting Q1860-90918

www.GovTechMedia.com