Manuals / Nortel Networks / Computer Equipment / Network Card

Nortel Networks Option 11C Mini manual Connecting the Chassis Expander to the Main Chassis, 135

Models: Option 11C Mini

1 334

Download 334 pages 10.31 Kb

Page 135

138

Page 135 of 332

Chapter 10 — Connecting the Chassis Expander to the Main Chassis

This chapter describes how to add a Chassis Expander to your Option 11C Mini system. Use the same methods described in “Chapter 9 — Installing the chassis” on page 115 to install the Chassis Expander. Refer to “Chapter 4 — Creating an equipment layout plan and a card slot assignment plan” on page 69 for measurements and distances between the Main Chassis and the Chassis Expander.

This chapter contains the following procedure:

•Procedure 6: “Adding a Chassis Expander” on page 135

The Chassis Expander connects to the Main Chassis by two copper cables: one provides DS-30X connectivity and the other provides CE-MUX connectivity to slot 10 only.

Procedure 6

Adding a Chassis Expander

1	Install the Chassis Expander following the procedures in
	“Chapter 9 — Installing the chassis” on page 115 .

2Connect one of the NTDK95 cables from the CE-MUX connector on the back of the Main Chassis to the CE-MUX connector on the back of the Chassis Expander.

3Tighten the screws on the connectors.

4Connect the other NTDK95 cable from the DS-30X connector on the back of the Main Chassis to the DS-30X connector on the back of the Chassis Expander.

Option 11C Mini Planning and Installation Guide

Image 135

Nortel Networks Option 11C Mini manual Connecting the Chassis Expander to the Main Chassis, 135

Contents

Option 11C Mini Planning and Installation GuidePage July Revision historyApril SeptemberStandard 3.00 April Contents 6 of 332 Contents Ystem and site requirementsRe gulatory information Important safet y instructions 101 Installin g the Option 11C MiniInstallin g the chassis 115 Contents Page 78 of 332 Contents Installin g the circuit cards 147Installin g and connecting Cross-connect terminal 169 Installin g Power Failure Transfer Units 185Connectin g the telephones Installin g and connecting SDI and Ethernet portsStartin g the Option 11C Mini and installing software Contents Page 9Appendix a Prepro grammed data 285 Connectin g an external alarm 27910 of 332 Contents Connectin g the trunks 253Appendix B Chan ging preprogrammed data Contents Page 1112 of 332 Contents About this guide Who should read this guideHow this guide is organized North American term UK term or meaning Terminology used in this guideRelated documents 16 of 332 About this guide Option 11C Mini system description Introducing the Option 11C MiniOption 11C Mini chassis Shows the Option 11C Mini Main ChassisSoftware Delivery Card Installing software and configuring dataSoftware Installation Program Flash DrivesSecurity Device Configuring dataSupported applications Set-Based AdministrationNumber of card slots System specificationsMeridian Administration Tools Meridian Mail MiniConference channels Power supplyTrunk capacity Software GenericData backup and restore methods On-site backupRemote backup Repair facilities EuropeRestoring data Page Identifying the Option 11C Mini equipment Main components of the Option 11C MiniNTDK91 Main Chassis NTDK92 Chassis Expander Cable connectors Chassis installation optionsPair connectors Connectors on the back of the Main Chassis Identifying the Option 11C Mini equipment Power supplyConnectors on the back of the Chassis Expander CoolingPower supply DIP switch settings Power switchPower status indicator Power supply DIP switch settingsEurope power supply DIP switch settings Asia Pacific/Cala power supply DIP switch settingsFront of chassis North American power supply DIP switch settingsReserve power supply Circuit cardsNTDK97 Mini System Controller card NTDK16 48-port Digital Line Card Telephones and Attendant ConsolesLists the Option 11C Mini cable kits and their contents Cables and wires38 of 332 Identifying the Option 11C Mini equipment Page Miscellaneous items for installation Comparison of Option 11C Mini and Option 11C Differences between Option 11C Mini and Option 11CNTDK78/NTDK75 Simm DLC Environmental requirements System and site requirementsWall Minimum fastener requirements Type of wall Fasteners Grounding requirements48 of 332 System and site requirements System and site requirements Single Point Grounding SPG Ground bus isolation Canada and the United StatesEMC Single point grounding Grounding method Chassis powered by different service panels Conduit requirementsGrounding multiple pieces of equipment in a rack/cabinet Commercial power requirements Max Outlet Type FrequencyMax Fuse Site requirementsIsolation transformer ground Alternative AC-powered installationLocation of power outlets Uninterruptible Power SupplyReceptacles Installing an Isolation Transformer60 of 332 System and site requirements Option 11C Mini Planning and Installation Guide Transformers without pluggable power cords Receptacle Power consumption worksheets for the Option 11C Mini system Total Total Option 11C Mini system power consumption Auxiliary equipment power Modem requirementsWith or without Meridian Mail Without Meridian Mail Maintenance and administration terminalsOn-site access Remote accessCross-connect terminal requirements Meridian Administration ToolsGeneral layout guidelines Equipment layout planStandard 3.00 April Main Maximum Leave at least Equipment layout plan for installing the chassis on a table Typical layout for installing the chassis on a table Option 11C Mini Planning and Installation Guide Typical layout for installing the chassis in a rack/cabinet Card slot assignments NTAK02 SDI/DCH NTAK03 TDS/DTR Card slot assignment plan Number CardsCard slot assignment plan Number Cards Card slot assignments for the Main Chassis Main ChassisCard slot assignments for the Chassis Expander Chassis ExpanderPage Regulatory information System approvalImportance of Ringer Equivalence Number Hearing aid compatibility Regulatory information Supported interfaces Safety specificationsCanadian and United States Network connections European compliance informationInformation for the United States Radio and TV interferenceAnalog PL facilities Jacks Port designationInformation for Canada 90 of 332 Regulatory information Standard 3.00 April Tools checklist Installing the Option 11C MiniSummary of installation procedures Readiness checklistInstalling the Option 11C Mini Faceplate on the Option 11C Mini chassis Installing the Option 11C Mini 96 of 332 Installing the Option 11C Mini Aligning the faceplate with the chassis Fitting the faceplate on to the front of the chassis Page Page Important safety instructions Symbols you must recognize101 Safety instructions when using telephone equipment Safety instructions when installing telephone equipmentImportant safety instructions 104 of 332 Important safety instructions Standard 3.00 April Bracing the Option 11C Mini against earthquakes Method for earthquake bracing105 Backboard size limits Determine fastener requirementsStud spacing Metal Studs Bracing the Option 11C Mini against earthquakesMaximum wall stud sizes 16 inch spacing Determine where to place the fasteners 110 of 332 Bracing the Option 11C Mini against earthquakes 111 Plywood fastener locations for concrete and masonry walls Continue with Option 11C Mini system installation End of ProcedurePage 115 Installing the chassisItems required Installing the chassis on a wall in a vertical positionInstalling the chassis Wall bracket fastened to backboard Draw a horizontal line on the plywood backboardFasten the chassis in position Chassis on a wall in a vertical position Installing the chassis on a wall in a horizontal position 122 of 332 Installing the chassis 123 Place the chassis on the shelf brackets Thumb screws on the wall shelf bracketsChassis stops on the wall shelf brackets Installing the chassis on a table 127 128 of 332 Installing the chassis Installing the chassis in a 19 inch rack/cabinet 130 of 332 Installing the chassis 131 Place the chassis on the chassis guide brackets Right ear bracket installed on the chassis133 134 of 332 Installing the chassis 135 Connecting the Chassis Expander to the Main ChassisDS-30X connection CE-MUX connection Connecting the Chassis Expander to the Main Chassis Page Installing the system ground Chassis powered by the same service panel139 140 of 332 Installing the system ground Chassis powered by different service panelsChassis grounding instructions NTBK80 ground block Grounding a Main Chassis and Chassis Expander pair Grounding multiple pieces of equipment in a rack/cabinet Grounding multiple pieces of equipment in a rack 146 of 332 Installing the system ground Standard 3.00 April 147 Installing the circuit cardsAntistatic wrist strap Circuit card assignments in the Main Chassis Installing the circuit cardsCircuit card assignments in the Chassis Expander NTDK97 Mini System Controller MSC card Circuit cards required for the Option 11C MiniPcmcia interface SDI portsEthernet interface Digitone Receiver, tone generation, tone detection functions MSC card with the security device installed Port Digital Line Card NTDK16 48-port Digital Line CardNT8D14 Universal Trunk card Optional circuit cardsInsert the card in its assigned slot NT8D15 E&M Trunk cardNTAK02 SDI/DCH card NT8D15 E&M Trunk card option settings Mode of operationProcedure NT8D02 circuit card installation NT8D02 Digital Line CardEsdi DCH/DPNSS Port Switch settings Ports 0Switch settings Ports 2 Jumper settings Strap Port Location For DTE For DCE RS422NTAK03 TDS/DTR card NTAG26 Xmfr card NT5K21 Xmfc card Set the jumpers NT1R20 Off-Premise Station OPS analog line cardTimp OPS analog line card jumper block locations OPS analog line card cross connections Digital Trunk cards168 of 332 Installing the circuit cards 169 Installing and connecting the cross-connect terminalTerminal block requirements Servicing Installing the BIX cross-connect terminalTypical BIX cross-connect terminal layout Installing the Reichle Masari cross-connect terminal GermanyTypical Reichle Masari cross-connect terminal layout Germany Installing the Krone Test Jack Frame for the UK Pair cable on three Krone strips Standard 3.00 April Typical Krone cross-connect terminal layout UK Other equipment Chassis Expander Main ChassisConnecting the cables Cable connectors on the back of the Main Chassis Pair cable to cross-connect terminal Ferrite filter AUX cable connector Designation Connection AUX cable termination information Wire ColorCross connections record Page Installing Power Failure Transfer Units Installing the Pftu185 J1 cable labels Pairs Control PFT1 PFT2 PFT3 PFT4 PFT5Auxiliary connector Installing Power Failure Transfer UnitsFunction Pair Connects Cross-connect to Number Color Control Control and power connections on cable J1NTAK1104 Pftu control lead signalsPower fail transfer Pftu control lead signalsPage 191 Installing and connecting SDI and Ethernet portsModem problems Problem Solution Modem setup requirementsInstalling and connecting SDI and Ethernet ports Installing and connecting SDI portsSDI cable connection An additional ferrite filter attached to the SDI cable 196 of 332 Installing and connecting SDI and Ethernet ports DTE NTAK02 connections at the cross-connect terminal Port RS232 Designations =input Signal =output 199NTAK02 connections at the cross-connect terminal Port Cable CTS BR-W Terminal setup Setup keys and functions Key Function CTS HP700/32 setup valuesXoff VT420 setup valuesVT220 setup values Ethernet connection Installing and connecting an ethernet cableProcedure Connecting the Ethernet cable Ethernet connectionEthernet cable inserted into an industry-standard MAU Page Starting the Option 11C Mini and installing software Starting the Option 11C Mini209 Power connector on the back of the chassis Start-up proceduresStarting the Option 11C Mini and installing software Software Installation ProgramFunction selection Starting the programKeycodes Customer database Feature set and ISM parametersPreconfigured database Security DeviceBacked up Database Installing software in a new systemRemote restored database Summary of stepsObserve the terminal screen Pcmcia card slot location Standard 3.00 April Example only Select the Feature Set to be enabledIf you selected 1 or 2, go to on 221 Current ISM Parameters Select ISM parameters Mopt Is this correct? n cr no 12121212 cr Page Xxxxxxxx cr Yyyyyyyy cr Zzzzzzzz cr Page 229 Connecting the telephonesCross connecting telephones NE-500/2500-type telephone cross connections Connecting the telephonesMeridian Digital Telephone cross connections Port Digital Line Card cross connections Connecting analog 500/2500-type telephones with a Pftu Connecting telephones without a PftuConnecting off-premise telephones Connecting an Attendant Console NTAK92AA Off-Premise Protection Module connections BL-Y +VPS RTN Attendant Console connectionsPFT Power Failure Transfer Unit connections Color combinations of cable pairs Unit ColorUnit Main Card Chassis MainExpander Cross-connecting terminal Digital Subscriber Loops Activating telephonesTelephone tones Telephone tones Tone Telephone tones for Germany Tone Description SpecificationPress the pound key # to select the default model Activating a default model with a character displayHang up the telephone receiver To accept the default extension number, press the pound keyActivating a default model without a character display Activating a customized model with a character display Hang up the telephone handset Activating a customized model without a character displayActivating terminals on a DSL Refer to the Isdn BRI Administration and Maintenance Guide252 of 332 Connecting the telephones Standard 3.00 April 253 Connecting the trunksConnecting trunks with a Pftu Connecting trunks without a PftuConnecting the trunks Page 255 Trunk connections NT8D14 Universal trunk connections Cable from chassis Paging All other Mode Modes Pair Color DesignationsPaging Type NT8D15 E&M Trunk card CablesTIE trunk card 2-Wire Trunk connections EuropeNT6D70 Silc and NT6D71 Uilc cards 2-wire Type Lead designations Pins Pair color Unit number TIE trunk card 4-wire TIE trunk card 4-WireSIG0A TIE trunk card 2280Hz TIE trunk card 4-wire Cables Card 1 through ColumnTIE trunk card MUS TIE trunk card RANCO & did trunk card Central Office trunk card NT5K17 Direct Inward Dial card terminations Trunk connections UKNT5K18 Exchange line trunk card terminations BK-O BK-G NT5K19 Analog TIE line trunk card terminations BK-BL BL-BK BK-BR BR-BK BK-BL BL-BK BK-G BK-BR BR-BK BL-R BR-R Instructions for the UK Activating a default model trunkEnter the default administration telephone password Select 1 ADD Trunk by entering the numberPress the digits to select a trunk model as assigned in LD Terminate the sequence by hanging up the telephone receiver Activating a selected model trunkHang up or repeat the sequence Enter the TN in Option 11 format Ccuu278 of 332 Connecting the trunks Standard 3.00 April Connecting an external alarm Alarm port assigned in software279 Alarm through a QUA6 Pftu Use LD 15 and make the following changesAC capacities Contacts in Pftu Connecting an external alarm282 of 332 Connecting an external alarm 22R Makes with 23T and 23R 22T Makes with 21T Open 284 of 332 Connecting an external alarm Standard 3.00 April 285 Appendix a Preprogrammed dataPasswords and codes Default numbering planPasswords and codes Function Code or extensions First digits Shows the default numbering plan for Option 11C MiniImportant extension numbers Extensions assigned to card slots Flexible Feature Codes Flexible Feature Codes FFC PromptDefinition Modem port SDI portsEnhanced Serial Data Interface Esdi port Esdi settingsEsdi settings Setting Code Telephone tonesTrunk routes DTN Timp Trunk models295 MUS XUT 3COM/900 Model telephonesLNA Class of Service options ACD telephones Prompt Meaning Administration telephone models M2008 telephone model Key number Feature PositionM2008 model M2616 model M2616 model 99 telephone Key Feature Number PositionM2616 and M2216 telephone model Key Feature Number Positio Central Answering Position CAP telephone modelsM2616 and M2216 CAP telephone model Analog 500/2500-type support personnel telephone models Analog 500/2500-type telephone modelsM2006 General business telephone models M2008 General business telephone models M2008 Two-line general business telephone models Appendix a Preprogrammed data Page 307 M2008 manager telephone models M2008 Message center telephone models ADD, FBD M2216 ACD telephone modelsADD, HFA, FBD M2616 Secretary telephone modelsM2616 Advanced business telephone M2616 Manager telephone models M2616 Message center telephone models Appendix B Changing preprogrammed data General information315 Changing the default numbering plan Changing the first number in the numbering planPress the asterisk * three times Determining new extension numbers Procedure Determine the extension numberExample Using the Meridian Mail Mini Auto-configure featureShifting the numbering plan to a new card slot Conflicts with Meridian Mail Mini data Removing numbering plan conflictsConflicts with ACD queues Obtaining the use of card slotObtaining the use of Meridian Mail Mini ACD queues Conflicts with Call Park extension numbers Conflicts with SDI portsConflicts with the Spre code Changing or removing the preprogrammed night number Conflicts with the attendant extension numberTo remove one access code, enter the following commands Conflicts with Flexible Feature CodesDesign model telephones Task Overlay Create model telephones Creating, changing, and removing model telephonesModifying analog model telephones Creating analog telephone modelsModifying digital model telephones Creating digital model telephonesDigital telephones Printing model informationRemoving model telephones Analog telephonesCreating model trunks Creating model trunks and changing route access codesRemoving model trunks Modifying model trunksSelect 2 Change Route Access by entering the number Changing a route access codeTerminate the sequence by hanging up the telephone Enter the new access code and press the pound keyPage Option 11C Mini Planning and Installation Guide