Trunk capacity, Software Generic | Nortel Networks Option 11C Mini

Chapter 1 — Introducing the Option 11C Mini	Page 23 of 332

The Chassis Expander provides four card slots. The Chassis Expander supports Meridian Mail Mini in Slot 10 only. You can place any IPE card in slots 7, 8, 9, and 10. The CE-MUX bus extends to slot 10 for Meridian Mail only.

An Option 11C Mini system, including a Main Chassis and a Chassis

Expander, supports eight physical and ten logical card slots.

The following is an example of a common Main Chassis configuration:

•one MSC card in slot 0

•one analog line card in slot 1, 2, or 3

•one digital trunk card in slot 1, 2, or 3

•one analog trunk card in slot 1, 2, or 3

•one NTDK16, 48-port Digital Line Card in Slot 4

The following is an example of a common Chassis Expander configuration:

•A line card in slots 7, 8, and 9

•Meridian Mail Mini in slot 10

Trunk capacity

It is difficult to estimate system capacities, as every installation varies depending on end-user needs. In a moderate to busy work environment, however, a common ratio of users to trunks normally falls between four and six users to each trunk.

Software Generic

The Option 11C Mini supports X11 Release 24.24 and later software.

Conference channels

The MSC card supports 16 conference channels.

Power supply

The universal power supply unit is installed inside the chassis before the system is sent to the customer. The power supply unit requires no installation by the customer. The power supply operates on standard line voltages of 100-240 VAC. Total output power is 363 Watts.

Note: The Option 11C Mini system does not support DC power input.

Option 11C Mini Planning and Installation Guide

Image 23

Nortel Networks Option 11C Mini manual Trunk capacity, Software Generic, Conference channels, Power supply

Contents

Option 11C Mini Planning and Installation GuidePage July Revision historyApril September Standard 3.00 April Contents Re gulatory information 6 of 332 ContentsYstem and site requirements Important safet y instructions 101 Installin g the Option 11C MiniInstallin g the chassis 115 Contents Page 7 8 of 332 Contents Installin g the circuit cards 147Installin g and connecting Cross-connect terminal 169 Installin g Power Failure Transfer Units 185 Connectin g the telephones Installin g and connecting SDI and Ethernet portsStartin g the Option 11C Mini and installing software Contents Page 9 Appendix a Prepro grammed data 285 Connectin g an external alarm 27910 of 332 Contents Connectin g the trunks 253 Appendix B Chan ging preprogrammed data Contents Page 11 12 of 332 Contents How this guide is organized About this guideWho should read this guide North American term UK term or meaning Terminology used in this guide Related documents 16 of 332 About this guide Option 11C Mini system description Introducing the Option 11C Mini Option 11C Mini chassis Shows the Option 11C Mini Main Chassis Software Delivery Card Installing software and configuring dataSoftware Installation Program Flash Drives Security Device Configuring data Supported applications Set-Based Administration Number of card slots System specificationsMeridian Administration Tools Meridian Mail Mini Conference channels Power supplyTrunk capacity Software Generic Remote backup Data backup and restore methodsOn-site backup Restoring data Repair facilitiesEurope Page NTDK91 Main Chassis NTDK92 Chassis Expander Identifying the Option 11C Mini equipmentMain components of the Option 11C Mini Cable connectors Chassis installation options Pair connectors Connectors on the back of the Main Chassis Identifying the Option 11C Mini equipment Power supplyConnectors on the back of the Chassis Expander Cooling Power supply DIP switch settings Power switchPower status indicator Power supply DIP switch settings Europe power supply DIP switch settings Asia Pacific/Cala power supply DIP switch settings Front of chassis North American power supply DIP switch settings NTDK97 Mini System Controller card Reserve power supplyCircuit cards NTDK16 48-port Digital Line Card Telephones and Attendant Consoles Lists the Option 11C Mini cable kits and their contents Cables and wires 38 of 332 Identifying the Option 11C Mini equipment Page Miscellaneous items for installation Comparison of Option 11C Mini and Option 11C Differences between Option 11C Mini and Option 11C NTDK78/NTDK75 Simm DLC Environmental requirements System and site requirements Wall Minimum fastener requirements Type of wall Fasteners Grounding requirements 48 of 332 System and site requirements System and site requirements Single Point Grounding SPG Ground bus isolation Canada and the United States EMC Single point grounding Grounding method Grounding multiple pieces of equipment in a rack/cabinet Chassis powered by different service panelsConduit requirements Commercial power requirements Max Outlet Type Frequency Max Fuse Site requirements Isolation transformer ground Alternative AC-powered installationLocation of power outlets Uninterruptible Power Supply Receptacles Installing an Isolation Transformer 60 of 332 System and site requirements Option 11C Mini Planning and Installation Guide Transformers without pluggable power cords Receptacle Power consumption worksheets for the Option 11C Mini system Total Total Option 11C Mini system power consumption With or without Meridian Mail Auxiliary equipment powerModem requirements Without Meridian Mail Maintenance and administration terminalsOn-site access Remote access Cross-connect terminal requirements Meridian Administration Tools General layout guidelines Equipment layout plan Standard 3.00 April Main Maximum Leave at least Equipment layout plan for installing the chassis on a table Typical layout for installing the chassis on a table Option 11C Mini Planning and Installation Guide Typical layout for installing the chassis in a rack/cabinet Card slot assignments NTAK02 SDI/DCH NTAK03 TDS/DTR Card slot assignment plan Number Cards Card slot assignment plan Number Cards Card slot assignments for the Main Chassis Main Chassis Card slot assignments for the Chassis Expander Chassis ExpanderPage Importance of Ringer Equivalence Number Regulatory informationSystem approval Hearing aid compatibility Regulatory information Supported interfaces Safety specificationsCanadian and United States Network connections European compliance information Information for the United States Radio and TV interference Analog PL facilities Jacks Port designation Information for Canada 90 of 332 Regulatory information Standard 3.00 April Tools checklist Installing the Option 11C Mini Summary of installation procedures Readiness checklist Installing the Option 11C Mini Faceplate on the Option 11C Mini chassis Installing the Option 11C Mini 96 of 332 Installing the Option 11C Mini Aligning the faceplate with the chassis Fitting the faceplate on to the front of the chassis Page Page 101 Important safety instructionsSymbols you must recognize Safety instructions when using telephone equipment Safety instructions when installing telephone equipment Important safety instructions 104 of 332 Important safety instructions Standard 3.00 April 105 Bracing the Option 11C Mini against earthquakesMethod for earthquake bracing Stud spacing Backboard size limitsDetermine fastener requirements Metal Studs Bracing the Option 11C Mini against earthquakes Maximum wall stud sizes 16 inch spacing Determine where to place the fasteners 110 of 332 Bracing the Option 11C Mini against earthquakes 111 Plywood fastener locations for concrete and masonry walls Continue with Option 11C Mini system installation End of ProcedurePage 115 Installing the chassis Items required Installing the chassis on a wall in a vertical position Installing the chassis Wall bracket fastened to backboard Draw a horizontal line on the plywood backboard Fasten the chassis in position Chassis on a wall in a vertical position Installing the chassis on a wall in a horizontal position 122 of 332 Installing the chassis 123 Place the chassis on the shelf brackets Thumb screws on the wall shelf brackets Chassis stops on the wall shelf brackets Installing the chassis on a table 127 128 of 332 Installing the chassis Installing the chassis in a 19 inch rack/cabinet 130 of 332 Installing the chassis 131 Place the chassis on the chassis guide brackets Right ear bracket installed on the chassis 133 134 of 332 Installing the chassis 135 Connecting the Chassis Expander to the Main Chassis DS-30X connection CE-MUX connection Connecting the Chassis Expander to the Main Chassis Page 139 Installing the system groundChassis powered by the same service panel 140 of 332 Installing the system ground Chassis powered by different service panels Chassis grounding instructions NTBK80 ground block Grounding a Main Chassis and Chassis Expander pair Grounding multiple pieces of equipment in a rack/cabinet Grounding multiple pieces of equipment in a rack 146 of 332 Installing the system ground Standard 3.00 April 147 Installing the circuit cards Antistatic wrist strap Circuit card assignments in the Main Chassis Installing the circuit cards Circuit card assignments in the Chassis Expander NTDK97 Mini System Controller MSC card Circuit cards required for the Option 11C Mini Ethernet interface Pcmcia interfaceSDI ports Digitone Receiver, tone generation, tone detection functions MSC card with the security device installed Port Digital Line Card NTDK16 48-port Digital Line Card NT8D14 Universal Trunk card Optional circuit cards Insert the card in its assigned slot NT8D15 E&M Trunk card NTAK02 SDI/DCH card NT8D15 E&M Trunk card option settings Mode of operationProcedure NT8D02 circuit card installation NT8D02 Digital Line Card Esdi DCH/DPNSS Port Switch settings Ports 0Switch settings Ports 2 Jumper settings Strap Port Location For DTE For DCE RS422 NTAK03 TDS/DTR card NTAG26 Xmfr card NT5K21 Xmfc card Set the jumpers NT1R20 Off-Premise Station OPS analog line card Timp OPS analog line card jumper block locations OPS analog line card cross connections Digital Trunk cards 168 of 332 Installing the circuit cards 169 Installing and connecting the cross-connect terminal Terminal block requirements Servicing Installing the BIX cross-connect terminal Typical BIX cross-connect terminal layout Installing the Reichle Masari cross-connect terminal Germany Typical Reichle Masari cross-connect terminal layout Germany Installing the Krone Test Jack Frame for the UK Pair cable on three Krone strips Standard 3.00 April Typical Krone cross-connect terminal layout UK Other equipment Chassis Expander Main Chassis Connecting the cables Cable connectors on the back of the Main Chassis Pair cable to cross-connect terminal Ferrite filter AUX cable connector Designation Connection AUX cable termination information Wire Color Cross connections record Page 185 Installing Power Failure Transfer UnitsInstalling the Pftu J1 cable labels Pairs Control PFT1 PFT2 PFT3 PFT4 PFT5 Auxiliary connector Installing Power Failure Transfer Units Function Pair Connects Cross-connect to Number Color Control Control and power connections on cable J1 NTAK1104 Pftu control lead signalsPower fail transfer Pftu control lead signalsPage 191 Installing and connecting SDI and Ethernet ports Modem problems Problem Solution Modem setup requirements Installing and connecting SDI and Ethernet ports Installing and connecting SDI ports SDI cable connection An additional ferrite filter attached to the SDI cable 196 of 332 Installing and connecting SDI and Ethernet ports DTE NTAK02 connections at the cross-connect terminal Port NTAK02 connections at the cross-connect terminal Port Cable RS232 Designations =input Signal =output199 CTS BR-W Terminal setup Setup keys and functions Key Function CTS HP700/32 setup values Xoff VT420 setup values VT220 setup values Ethernet connection Installing and connecting an ethernet cableProcedure Connecting the Ethernet cable Ethernet connection Ethernet cable inserted into an industry-standard MAU Page 209 Starting the Option 11C Mini and installing softwareStarting the Option 11C Mini Power connector on the back of the chassis Start-up procedures Starting the Option 11C Mini and installing software Software Installation Program Function selection Starting the program Keycodes Customer database Feature set and ISM parametersPreconfigured database Security Device Backed up Database Installing software in a new systemRemote restored database Summary of steps Observe the terminal screen Pcmcia card slot location Standard 3.00 April Example only Select the Feature Set to be enabled If you selected 1 or 2, go to on 221 Current ISM Parameters Select ISM parameters Mopt Is this correct? n cr no 12121212 cr Page Xxxxxxxx cr Yyyyyyyy cr Zzzzzzzz cr Page 229 Connecting the telephones Cross connecting telephones NE-500/2500-type telephone cross connections Connecting the telephones Meridian Digital Telephone cross connections Port Digital Line Card cross connections Connecting analog 500/2500-type telephones with a Pftu Connecting telephones without a Pftu Connecting off-premise telephones Connecting an Attendant Console NTAK92AA Off-Premise Protection Module connections BL-Y +VPS RTN Attendant Console connections PFT Power Failure Transfer Unit connections Unit Color combinations of cable pairsUnit Color Main Card Expander ChassisMain Telephone tones Cross-connecting terminal Digital Subscriber LoopsActivating telephones Telephone tones Tone Telephone tones for Germany Tone Description Specification Press the pound key # to select the default model Activating a default model with a character display Hang up the telephone receiver To accept the default extension number, press the pound key Activating a default model without a character display Activating a customized model with a character display Hang up the telephone handset Activating a customized model without a character display Activating terminals on a DSL Refer to the Isdn BRI Administration and Maintenance Guide 252 of 332 Connecting the telephones Standard 3.00 April 253 Connecting the trunks Connecting trunks with a Pftu Connecting trunks without a Pftu Connecting the trunks Page 255 Trunk connections NT8D14 Universal trunk connections Cable from chassis Paging All other Mode Modes Pair Color Designations Paging Type NT8D15 E&M Trunk card Cables NT6D70 Silc and NT6D71 Uilc cards TIE trunk card 2-WireTrunk connections Europe 2-wire Type Lead designations Pins Pair color Unit number TIE trunk card 4-wire TIE trunk card 4-Wire SIG0A TIE trunk card 2280Hz TIE trunk card 4-wire Cables Card 1 through Column TIE trunk card MUS TIE trunk card RAN CO & did trunk card Central Office trunk card NT5K17 Direct Inward Dial card terminations Trunk connections UK NT5K18 Exchange line trunk card terminations BK-O BK-G NT5K19 Analog TIE line trunk card terminations BK-BL BL-BK BK-BR BR-BK BK-BL BL-BK BK-G BK-BR BR-BK BL-R BR-R Instructions for the UK Activating a default model trunk Press the digits to select a trunk model as assigned in LD Enter the default administration telephone passwordSelect 1 ADD Trunk by entering the number Terminate the sequence by hanging up the telephone receiver Activating a selected model trunk Hang up or repeat the sequence Enter the TN in Option 11 format Ccuu 278 of 332 Connecting the trunks Standard 3.00 April 279 Connecting an external alarmAlarm port assigned in software AC capacities Alarm through a QUA6 PftuUse LD 15 and make the following changes Contacts in Pftu Connecting an external alarm 282 of 332 Connecting an external alarm 22R Makes with 23T and 23R 22T Makes with 21T Open 284 of 332 Connecting an external alarm Standard 3.00 April 285 Appendix a Preprogrammed data Passwords and codes Function Code or extensions Passwords and codesDefault numbering plan First digits Shows the default numbering plan for Option 11C Mini Important extension numbers Extensions assigned to card slots Definition Flexible Feature CodesFlexible Feature Codes FFC Prompt Modem port SDI ports Enhanced Serial Data Interface Esdi port Esdi settingsEsdi settings Setting Code Telephone tones Trunk routes DTN Timp Trunk models 295 MUS XUT 3COM/900 Model telephones LNA Class of Service options ACD telephones Prompt Meaning M2008 model Administration telephone modelsM2008 telephone model Key number Feature Position M2616 model M2616 model 99 telephone Key Feature Number Position M2616 and M2216 CAP telephone model M2616 and M2216 telephone model Key Feature Number PositioCentral Answering Position CAP telephone models Analog 500/2500-type support personnel telephone models Analog 500/2500-type telephone models M2006 General business telephone models M2008 General business telephone models M2008 Two-line general business telephone models Appendix a Preprogrammed data Page 307 M2008 manager telephone models M2008 Message center telephone models ADD, FBD M2216 ACD telephone models ADD, HFA, FBD M2616 Secretary telephone models M2616 Advanced business telephone M2616 Manager telephone models M2616 Message center telephone models 315 Appendix B Changing preprogrammed dataGeneral information Press the asterisk * three times Changing the default numbering planChanging the first number in the numbering plan Determining new extension numbers Procedure Determine the extension number Example Using the Meridian Mail Mini Auto-configure feature Shifting the numbering plan to a new card slot Conflicts with Meridian Mail Mini data Removing numbering plan conflicts Obtaining the use of Meridian Mail Mini ACD queues Conflicts with ACD queuesObtaining the use of card slot Conflicts with the Spre code Conflicts with Call Park extension numbersConflicts with SDI ports Changing or removing the preprogrammed night number Conflicts with the attendant extension number To remove one access code, enter the following commands Conflicts with Flexible Feature Codes Design model telephones Task Overlay Create model telephones Creating, changing, and removing model telephones Modifying analog model telephones Creating analog telephone models Modifying digital model telephones Creating digital model telephones Digital telephones Printing model informationRemoving model telephones Analog telephones Creating model trunks Creating model trunks and changing route access codes Removing model trunks Modifying model trunks Select 2 Change Route Access by entering the number Changing a route access code Terminate the sequence by hanging up the telephone Enter the new access code and press the pound keyPage Option 11C Mini Planning and Installation Guide