Manuals / Nortel Networks / Computer Equipment / Network Card

Nortel Networks manual Total Total Option 11C Mini system power consumption

Models: Option 11C Mini

1 334

Download 334 pages 10.31 Kb

Page 65

Chapter 3 — System and site requirements Page 65 of 332

Table 15

Option 11C Mini power consumption: Main Chassis

			Power
Slot	Circuit card	Type	consumption
			from Table 14

1	NTDK97	MSC	15 w

2

3

4, 5, 6	NTDK16	48 port DLC	75w

		Total

Table 16

Option 11C Mini power consumption: Chassis Expander

					Power
Slot	Circuit card	Type			consumption
					from Table 14

7

8

9

10

			Total

Table 17

Total Option 11C Mini system power consumption

Pout Main (total for slots 1-6 in main chassis)

Pout Expan (total for slots 7-10 in the chassis expander)

Total

Option 11C Mini Planning and Installation Guide

Image 65

Nortel Networks manual Total Total Option 11C Mini system power consumption

Contents

Option 11C Mini Planning and Installation GuidePage April Revision historySeptember JulyStandard 3.00 April Contents Re gulatory information 6 of 332 ContentsYstem and site requirements Installin g the chassis 115 Installin g the Option 11C MiniContents Page 7 Important safet y instructions 101Installin g and connecting Cross-connect terminal 169 Installin g the circuit cards 147Installin g Power Failure Transfer Units 185 8 of 332 ContentsStartin g the Option 11C Mini and installing software Installin g and connecting SDI and Ethernet portsContents Page 9 Connectin g the telephones10 of 332 Contents Connectin g an external alarm 279Connectin g the trunks 253 Appendix a Prepro grammed data 285Appendix B Chan ging preprogrammed data Contents Page 1112 of 332 Contents How this guide is organized About this guideWho should read this guide North American term UK term or meaning Terminology used in this guideRelated documents 16 of 332 About this guide Option 11C Mini system description Introducing the Option 11C MiniOption 11C Mini chassis Shows the Option 11C Mini Main ChassisSoftware Installation Program Installing software and configuring dataFlash Drives Software Delivery CardSecurity Device Configuring dataSupported applications Set-Based AdministrationMeridian Administration Tools System specificationsMeridian Mail Mini Number of card slotsTrunk capacity Power supplySoftware Generic Conference channelsRemote backup Data backup and restore methodsOn-site backup Restoring data Repair facilitiesEurope Page NTDK91 Main Chassis NTDK92 Chassis Expander Identifying the Option 11C Mini equipmentMain components of the Option 11C Mini Cable connectors Chassis installation optionsPair connectors Connectors on the back of the Main Chassis Connectors on the back of the Chassis Expander Power supplyCooling Identifying the Option 11C Mini equipmentPower status indicator Power switchPower supply DIP switch settings Power supply DIP switch settingsEurope power supply DIP switch settings Asia Pacific/Cala power supply DIP switch settingsFront of chassis North American power supply DIP switch settingsNTDK97 Mini System Controller card Reserve power supplyCircuit cards NTDK16 48-port Digital Line Card Telephones and Attendant ConsolesLists the Option 11C Mini cable kits and their contents Cables and wires38 of 332 Identifying the Option 11C Mini equipment Page Miscellaneous items for installation Comparison of Option 11C Mini and Option 11C Differences between Option 11C Mini and Option 11CNTDK78/NTDK75 Simm DLC Environmental requirements System and site requirementsWall Minimum fastener requirements Type of wall Fasteners Grounding requirements48 of 332 System and site requirements System and site requirements Single Point Grounding SPG Ground bus isolation Canada and the United StatesEMC Single point grounding Grounding method Grounding multiple pieces of equipment in a rack/cabinet Chassis powered by different service panelsConduit requirements Commercial power requirements Max Outlet Type FrequencyMax Fuse Site requirementsLocation of power outlets Alternative AC-powered installationUninterruptible Power Supply Isolation transformer groundReceptacles Installing an Isolation Transformer60 of 332 System and site requirements Option 11C Mini Planning and Installation Guide Transformers without pluggable power cords Receptacle Power consumption worksheets for the Option 11C Mini system Total Total Option 11C Mini system power consumption With or without Meridian Mail Auxiliary equipment powerModem requirements On-site access Maintenance and administration terminalsRemote access Without Meridian MailCross-connect terminal requirements Meridian Administration ToolsGeneral layout guidelines Equipment layout planStandard 3.00 April Main Maximum Leave at least Equipment layout plan for installing the chassis on a table Typical layout for installing the chassis on a table Option 11C Mini Planning and Installation Guide Typical layout for installing the chassis in a rack/cabinet Card slot assignments NTAK02 SDI/DCH NTAK03 TDS/DTR Card slot assignment plan Number CardsCard slot assignment plan Number Cards Card slot assignments for the Main Chassis Main ChassisCard slot assignments for the Chassis Expander Chassis ExpanderPage Importance of Ringer Equivalence Number Regulatory informationSystem approval Hearing aid compatibility Regulatory information Canadian and United States Network connections Safety specificationsEuropean compliance information Supported interfacesInformation for the United States Radio and TV interferenceAnalog PL facilities Jacks Port designationInformation for Canada 90 of 332 Regulatory information Standard 3.00 April Tools checklist Installing the Option 11C MiniSummary of installation procedures Readiness checklistInstalling the Option 11C Mini Faceplate on the Option 11C Mini chassis Installing the Option 11C Mini 96 of 332 Installing the Option 11C Mini Aligning the faceplate with the chassis Fitting the faceplate on to the front of the chassis Page Page 101 Important safety instructionsSymbols you must recognize Safety instructions when using telephone equipment Safety instructions when installing telephone equipmentImportant safety instructions 104 of 332 Important safety instructions Standard 3.00 April 105 Bracing the Option 11C Mini against earthquakesMethod for earthquake bracing Stud spacing Backboard size limitsDetermine fastener requirements Metal Studs Bracing the Option 11C Mini against earthquakesMaximum wall stud sizes 16 inch spacing Determine where to place the fasteners 110 of 332 Bracing the Option 11C Mini against earthquakes 111 Plywood fastener locations for concrete and masonry walls Continue with Option 11C Mini system installation End of ProcedurePage 115 Installing the chassisItems required Installing the chassis on a wall in a vertical positionInstalling the chassis Wall bracket fastened to backboard Draw a horizontal line on the plywood backboardFasten the chassis in position Chassis on a wall in a vertical position Installing the chassis on a wall in a horizontal position 122 of 332 Installing the chassis 123 Place the chassis on the shelf brackets Thumb screws on the wall shelf bracketsChassis stops on the wall shelf brackets Installing the chassis on a table 127 128 of 332 Installing the chassis Installing the chassis in a 19 inch rack/cabinet 130 of 332 Installing the chassis 131 Place the chassis on the chassis guide brackets Right ear bracket installed on the chassis133 134 of 332 Installing the chassis 135 Connecting the Chassis Expander to the Main ChassisDS-30X connection CE-MUX connection Connecting the Chassis Expander to the Main Chassis Page 139 Installing the system groundChassis powered by the same service panel 140 of 332 Installing the system ground Chassis powered by different service panelsChassis grounding instructions NTBK80 ground block Grounding a Main Chassis and Chassis Expander pair Grounding multiple pieces of equipment in a rack/cabinet Grounding multiple pieces of equipment in a rack 146 of 332 Installing the system ground Standard 3.00 April 147 Installing the circuit cardsAntistatic wrist strap Circuit card assignments in the Main Chassis Installing the circuit cardsCircuit card assignments in the Chassis Expander NTDK97 Mini System Controller MSC card Circuit cards required for the Option 11C MiniEthernet interface Pcmcia interfaceSDI ports Digitone Receiver, tone generation, tone detection functions MSC card with the security device installed Port Digital Line Card NTDK16 48-port Digital Line CardNT8D14 Universal Trunk card Optional circuit cardsInsert the card in its assigned slot NT8D15 E&M Trunk cardProcedure NT8D02 circuit card installation NT8D15 E&M Trunk card option settings Mode of operationNT8D02 Digital Line Card NTAK02 SDI/DCH cardEsdi DCH/DPNSS Switch settings Ports 2 Switch settings Ports 0Jumper settings Strap Port Location For DTE For DCE RS422 PortNTAK03 TDS/DTR card NTAG26 Xmfr card NT5K21 Xmfc card Set the jumpers NT1R20 Off-Premise Station OPS analog line cardTimp OPS analog line card jumper block locations OPS analog line card cross connections Digital Trunk cards168 of 332 Installing the circuit cards 169 Installing and connecting the cross-connect terminalTerminal block requirements Servicing Installing the BIX cross-connect terminalTypical BIX cross-connect terminal layout Installing the Reichle Masari cross-connect terminal GermanyTypical Reichle Masari cross-connect terminal layout Germany Installing the Krone Test Jack Frame for the UK Pair cable on three Krone strips Standard 3.00 April Typical Krone cross-connect terminal layout UK Other equipment Chassis Expander Main ChassisConnecting the cables Cable connectors on the back of the Main Chassis Pair cable to cross-connect terminal Ferrite filter AUX cable connector Designation Connection AUX cable termination information Wire ColorCross connections record Page 185 Installing Power Failure Transfer UnitsInstalling the Pftu J1 cable labels Pairs Control PFT1 PFT2 PFT3 PFT4 PFT5Auxiliary connector Installing Power Failure Transfer UnitsFunction Pair Connects Cross-connect to Number Color Control Control and power connections on cable J1Power fail transfer Pftu control lead signalsPftu control lead signals NTAK1104Page 191 Installing and connecting SDI and Ethernet portsModem problems Problem Solution Modem setup requirementsInstalling and connecting SDI and Ethernet ports Installing and connecting SDI portsSDI cable connection An additional ferrite filter attached to the SDI cable 196 of 332 Installing and connecting SDI and Ethernet ports DTE NTAK02 connections at the cross-connect terminal Port NTAK02 connections at the cross-connect terminal Port Cable RS232 Designations =input Signal =output199 CTS BR-W Terminal setup Setup keys and functions Key Function CTS HP700/32 setup valuesXoff VT420 setup valuesVT220 setup values Procedure Connecting the Ethernet cable Installing and connecting an ethernet cableEthernet connection Ethernet connectionEthernet cable inserted into an industry-standard MAU Page 209 Starting the Option 11C Mini and installing softwareStarting the Option 11C Mini Power connector on the back of the chassis Start-up proceduresStarting the Option 11C Mini and installing software Software Installation ProgramFunction selection Starting the programKeycodes Preconfigured database Feature set and ISM parametersSecurity Device Customer databaseRemote restored database Installing software in a new systemSummary of steps Backed up DatabaseObserve the terminal screen Pcmcia card slot location Standard 3.00 April Example only Select the Feature Set to be enabledIf you selected 1 or 2, go to on 221 Current ISM Parameters Select ISM parameters Mopt Is this correct? n cr no 12121212 cr Page Xxxxxxxx cr Yyyyyyyy cr Zzzzzzzz cr Page 229 Connecting the telephonesCross connecting telephones NE-500/2500-type telephone cross connections Connecting the telephonesMeridian Digital Telephone cross connections Port Digital Line Card cross connections Connecting analog 500/2500-type telephones with a Pftu Connecting telephones without a PftuConnecting off-premise telephones Connecting an Attendant Console NTAK92AA Off-Premise Protection Module connections BL-Y +VPS RTN Attendant Console connectionsPFT Power Failure Transfer Unit connections Unit Color combinations of cable pairsUnit Color Main Card Expander ChassisMain Telephone tones Cross-connecting terminal Digital Subscriber LoopsActivating telephones Telephone tones Tone Telephone tones for Germany Tone Description SpecificationPress the pound key # to select the default model Activating a default model with a character displayHang up the telephone receiver To accept the default extension number, press the pound keyActivating a default model without a character display Activating a customized model with a character display Hang up the telephone handset Activating a customized model without a character displayActivating terminals on a DSL Refer to the Isdn BRI Administration and Maintenance Guide252 of 332 Connecting the telephones Standard 3.00 April 253 Connecting the trunksConnecting trunks with a Pftu Connecting trunks without a PftuConnecting the trunks Page 255 Trunk connections NT8D14 Universal trunk connections Cable from chassis Paging All other Mode Modes Pair Color DesignationsPaging Type NT8D15 E&M Trunk card CablesNT6D70 Silc and NT6D71 Uilc cards TIE trunk card 2-WireTrunk connections Europe 2-wire Type Lead designations Pins Pair color Unit number TIE trunk card 4-wire TIE trunk card 4-WireSIG0A TIE trunk card 2280Hz TIE trunk card 4-wire Cables Card 1 through ColumnTIE trunk card MUS TIE trunk card RANCO & did trunk card Central Office trunk card NT5K17 Direct Inward Dial card terminations Trunk connections UKNT5K18 Exchange line trunk card terminations BK-O BK-G NT5K19 Analog TIE line trunk card terminations BK-BL BL-BK BK-BR BR-BK BK-BL BL-BK BK-G BK-BR BR-BK BL-R BR-R Instructions for the UK Activating a default model trunkPress the digits to select a trunk model as assigned in LD Enter the default administration telephone passwordSelect 1 ADD Trunk by entering the number Terminate the sequence by hanging up the telephone receiver Activating a selected model trunkHang up or repeat the sequence Enter the TN in Option 11 format Ccuu278 of 332 Connecting the trunks Standard 3.00 April 279 Connecting an external alarmAlarm port assigned in software AC capacities Alarm through a QUA6 PftuUse LD 15 and make the following changes Contacts in Pftu Connecting an external alarm282 of 332 Connecting an external alarm 22R Makes with 23T and 23R 22T Makes with 21T Open 284 of 332 Connecting an external alarm Standard 3.00 April 285 Appendix a Preprogrammed dataPasswords and codes Function Code or extensions Passwords and codesDefault numbering plan First digits Shows the default numbering plan for Option 11C MiniImportant extension numbers Extensions assigned to card slots Definition Flexible Feature CodesFlexible Feature Codes FFC Prompt Modem port SDI portsEsdi settings Setting Code Esdi settingsTelephone tones Enhanced Serial Data Interface Esdi portTrunk routes DTN Timp Trunk models295 MUS XUT 3COM/900 Model telephonesLNA Class of Service options ACD telephones Prompt Meaning M2008 model Administration telephone modelsM2008 telephone model Key number Feature Position M2616 model M2616 model 99 telephone Key Feature Number PositionM2616 and M2216 CAP telephone model M2616 and M2216 telephone model Key Feature Number PositioCentral Answering Position CAP telephone models Analog 500/2500-type support personnel telephone models Analog 500/2500-type telephone modelsM2006 General business telephone models M2008 General business telephone models M2008 Two-line general business telephone models Appendix a Preprogrammed data Page 307 M2008 manager telephone models M2008 Message center telephone models ADD, FBD M2216 ACD telephone modelsADD, HFA, FBD M2616 Secretary telephone modelsM2616 Advanced business telephone M2616 Manager telephone models M2616 Message center telephone models 315 Appendix B Changing preprogrammed dataGeneral information Press the asterisk * three times Changing the default numbering planChanging the first number in the numbering plan Determining new extension numbers Procedure Determine the extension numberExample Using the Meridian Mail Mini Auto-configure featureShifting the numbering plan to a new card slot Conflicts with Meridian Mail Mini data Removing numbering plan conflictsObtaining the use of Meridian Mail Mini ACD queues Conflicts with ACD queuesObtaining the use of card slot Conflicts with the Spre code Conflicts with Call Park extension numbersConflicts with SDI ports Changing or removing the preprogrammed night number Conflicts with the attendant extension numberTo remove one access code, enter the following commands Conflicts with Flexible Feature CodesDesign model telephones Task Overlay Create model telephones Creating, changing, and removing model telephonesModifying analog model telephones Creating analog telephone modelsModifying digital model telephones Creating digital model telephonesRemoving model telephones Printing model informationAnalog telephones Digital telephonesCreating model trunks Creating model trunks and changing route access codesRemoving model trunks Modifying model trunksSelect 2 Change Route Access by entering the number Changing a route access codeTerminate the sequence by hanging up the telephone Enter the new access code and press the pound keyPage Option 11C Mini Planning and Installation Guide