Manuals / Q-Logic / Computer Equipment / Switch

Q-Logic MKII-BASE16 user manual Fiber Continuity Tests, Did this correct the problem?

Models: MKII-BASE16

1 138

Download 138 pages 23.54 Kb

Page 113

Fiber Continuity Test

Fiber Continuity Tests

When there is a problem communicating over a particular fiber link and both the Switch and the N_Port adapter pass their respective tests, check the continuity of the fiber optic cables.

Step 1

If possible, swap another set of fiber optic cables into the faulty link.

Did this correct the problem?

Yes	Replace the faulty cable.
No	Contact your service representative.

Step 2

If it is not possible to swap a different set of fiber cables into the faulty link, disconnect the SC connectors from both ends of the faulty link and shine a flashlight through each fiber (one fiber at a time).

Did light shine through each fiber?

No	Replace the faulty cable.
Yes	Contact Ancor Customer Service or your authorized maintenance provider.

GigWorks MkII-16 Switch Model MKII-BASE16		Diagnostics/Troubleshooting 4-15
Installer's/User's Manual	59003-01 Rev. A

Image 113

Q-Logic MKII-BASE16 user manual Fiber Continuity Tests, Did this correct the problem?, Did light shine through each fiber?

Contents

GigWorks MKII-16 Switch Model MKII-BASE16 Release Number 01, Revision a December Table Of Contents Table Of Contents Switch Management Diagnostics/Troubleshooting Table Of ContentsRemoval/Replacement Procedures Appendix B Ancor Customer ServiceList Of Tables Table Of Contents Appendix C Chassis Switch PanelList Of Figures Intended Audience How to Use This ManualRelated Materials Ancor Customer ServiceCommunications Statements Safety NoticesCommunications Statements Federal Communications Commission FCC Class a StatementCE Statement Communications Statements Vcci Class a Statement Certification and Classification Information Laser Safety InformationLaser Safety Information Usage Restrictions Laser Safety Information Optical GBICsLaser Safety Information Labeling Requirements Pièces Accessibles Accessible PartsAccessible Parts Zugängliche TeileTable Of Contents Major Fibre Channel Port Features GigWorks MKII-16 SwitchGeneral Description Major Switch Management FeaturesGeneral Description Major Switch Chassis Features Fibre Channel Ports Chassis Front Typical Gbic Front Panel LEDs General Description Front Panel ControlsNot used. OFF Refer to Figure Chassis BackOverheat Light Red Power Good Light GreenChassis Switch Panel Unpack InstallationRack Mount Installation Place or Mount the EquipmentShelf Mount Cabinet Mounting Bracket To IEC 825 1984 + Cenelec HD 482 S1 Install GBICsGefahr Installation Connect to AC Power6Installation Check the Power-On-Self-Test Post Results Logic Power Good LEDTuning Cable N or NLPort Adapters to the SwitchPorts DistanceNPort Connections Incorrect CablingFiber Optic Connections Copper Connections10Installation Cabling Operating the Switch Introduction GigWorks Mkii Switch UtilitiesIntroduction Simple Network Management Protocol Snmp Trivial File Transfer Protocol TftpEthernet Cabling Ethernet CablingConfiguring the Ethernet Port Using the Switch Utilities Configuring the Switch Ethernet PortConfiguring the Switch Ethernet Port Configuring the Ethernet Port Using Tftp Configuring Multiple SwitchesGetting Started Loading the Switch UtilitiesUsing the Switch Utilities Switch UtilitiesFileOpen FileSaveHelpAbout FileSave AsFileExit Switch Utilities Management Information Error Group Tables Configuration Group TablesOperation Group Tables Account Group TableGroup Select List Port FieldTable Select List Read ButtonFlash File Name Switch Utilities FlashReset the Ancor GigWorks Mkii Switch Cancel Button or the Flash Load FailsLoad Flash Flash Load ProgressVersion Information Switch Utilities VersionsWorld Wide Name Refresh Button Switch on FrontSwitches on Back Switch Utilities Diagnostics Trace Enables All Button Enables Radio ButtonEnables Read Button Enables Apply Button Enables None ButtonEnables Information Display Window Trace Clear ButtonDisplay Quantity Box Display Offset BoxDisplay Read Button Display Read All ButtonEthernet IP Address Box Switch Utilities SetupEthernet Port Radio Button COMx Selection Box Legacy Switches only Serial Port Radio Button Legacy Switches onlyUDP Port # Box Use Sequence CheckboxChassis Number Switch Utilities Chassis ConfigurationFabric ID Rttov Stage Type Radio ButtonsApply Button Administration/Operation StatesSwitch Utilities Port Status Loop Devices Window 28Switch Management Switch Utilities Zoning Hard Zone Rules Broadcast Zone Rules Zoning Screen Switch Utilities Zoning Switch Utilities Name Server Switch Utilities Name Server Switch Utilities Management Configuration Snmp Configuration 38Switch Management Reset the Switch and the current Management firmware Managing the Switch Using Tftp Managing the Switch Using TftpTransfer a New Management Configuration File to the Switch SnmpReadCommunity SnmpLocation Loading New Switch Control Code into FlashLoading New Management Interface Flash 16-Port Switch only Reset the Switch Using Tftp Transfer the file to the Switch Retrieve the file from the Switch Network Management Managing the Switch Using SnmpFunction Description Network Management StationTask Description Node AgentsManagement Information Bases MIBs Property DescriptionFuture use Polling-Only Data Collection Simple Network Management ProtocolTrap-Directed Polling Data Collection Interrupt-Based Data CollectionCommunity Type Description 16 Trap-Directed Polling Data CollectionFile Name Location and Description MIB II RFC 1213 Groups Management Information Base MIBMkii Utility MIB Configuring Snmp58Switch Management Power Supply Troubleshooting Diagnostics/TroubleshootingCorrective Action Power Supply/Fan TroubleshootingPower Supply Troubleshooting For example Overview Power-On-Self-Test PostPower-On-Self-Test Post 6Diagnostics/Troubleshooting Test/Failure Descriptions Heartbeat LED Blink PatternsProm Checksum Failure 1 Blink Gbic Bypass Port Loopback Test Failure 7 Blinks Switch Auto-Route Test Failure 10 Blinks Switch Management Port Failure 14 Blinks Continuous Test Continuous TestStep ProcedureIs the Logic Power Good LED lit? 14Diagnostics/Troubleshooting Fiber Continuity Tests Did this correct the problem?Fiber Continuity Test Did light shine through each fiber?Diagnostics/Troubleshooting Removal Input FuseFuses Amp Fuse Holder Input Fuse ReplacementGbic 4Removal/Replacement Procedures Port Connector Power Supply Power SupplyPower Supply Replacement Removal/Replacement Procedures Switch GigWorks MKII-16 Switch Model MKII-BASE16 Specifications2Reference Information Gb/s, even though backplanes Tftp TUV Longwave Laser Gbic single-mode Shortwave Laser Gbic multi-modeCopper Intra-Enclosure Gbic passive Copper Inter-Enclosure Gbic activeReference Information Front ViewDimensions in mm inches Reference Information Description Consists Help DeskContact Us Hardware SupportCustomer Responsibilities Ancor Customer Service Software SupportFor supported software Appendix C Chassis Switch PanelForce Prom Mode Chassis Switch Panel ResetBit Test Mode Chassis Switch Panel Watch Dog Timer DisableTest Mode Area Fabric Stage