Manuals / Q-Logic / Computer Equipment / Switch

Q-Logic MKII-BASE16 user manual Input Fuse, Removal

Models: MKII-BASE16

1 138

Download 138 pages 23.54 Kb

Page 115

Section 5	Removal/Replacement
	Procedures

Introduction

The only Field Replaceable Units (FRUs) in the Switch are Input Fuses, GBICs, and the Power Supply(s).

Input Fuse

Removal

1.Unplug the AC Power Cable from the back of the Switch chassis.

2.Insert a thin-blade screwdriver into the slot behind the tab and use it to pull the Fuse Holder out the front of the AC Power Plug Assembly.

3.Pull the Fuse(s) from the Fuse Holder.

AC Power Plug Assembly

Fuse Holder

Slot Tab behind

Tab

GigWorks MKII-16 Switch Model MKII-BASE16		Removal/Replacement Procedures 5-1
Installer's/User's Manual	59003-01 Rev. A

Image 115

Q-Logic MKII-BASE16 user manual Input Fuse, Removal

Contents

GigWorks MKII-16 Switch Model MKII-BASE16 Release Number 01, Revision a December Table Of Contents Table Of Contents Switch Management Appendix B Ancor Customer Service Table Of ContentsDiagnostics/Troubleshooting Removal/Replacement ProceduresList Of Figures Table Of Contents Appendix C Chassis Switch PanelList Of Tables Intended Audience How to Use This ManualRelated Materials Ancor Customer ServiceFederal Communications Commission FCC Class a Statement Safety NoticesCommunications Statements Communications StatementsCE Statement Communications Statements Vcci Class a Statement Laser Safety Information Laser Safety InformationCertification and Classification Information Usage Restrictions Laser Safety Information Optical GBICsLaser Safety Information Labeling Requirements Zugängliche Teile Accessible PartsPièces Accessibles Accessible PartsTable Of Contents Major Fibre Channel Port Features GigWorks MKII-16 SwitchGeneral Description Major Switch Management FeaturesGeneral Description Major Switch Chassis Features Fibre Channel Ports Chassis Front Typical Gbic Front Panel LEDs General Description Front Panel ControlsNot used. OFF Refer to Figure Chassis BackOverheat Light Red Power Good Light GreenChassis Switch Panel Unpack InstallationShelf Mount Installation Place or Mount the EquipmentRack Mount Cabinet Mounting Bracket To IEC 825 1984 + Cenelec HD 482 S1 Install GBICsGefahr Installation Connect to AC Power6Installation Check the Power-On-Self-Test Post Results Logic Power Good LEDDistance Cable N or NLPort Adapters to the SwitchTuning PortsCopper Connections Incorrect CablingNPort Connections Fiber Optic Connections10Installation Cabling Operating the Switch Introduction GigWorks Mkii Switch UtilitiesIntroduction Simple Network Management Protocol Snmp Trivial File Transfer Protocol TftpEthernet Cabling Ethernet CablingConfiguring the Switch Ethernet Port Configuring the Switch Ethernet PortConfiguring the Ethernet Port Using the Switch Utilities Configuring the Ethernet Port Using Tftp Configuring Multiple SwitchesGetting Started Loading the Switch UtilitiesFileSave Switch UtilitiesUsing the Switch Utilities FileOpenFileExit FileSave AsHelpAbout Switch Utilities Management Information Account Group Table Configuration Group TablesError Group Tables Operation Group TablesRead Button Port FieldGroup Select List Table Select ListFlash File Name Switch Utilities FlashFlash Load Progress Cancel Button or the Flash Load FailsReset the Ancor GigWorks Mkii Switch Load FlashWorld Wide Name Switch Utilities VersionsVersion Information Switches on Back Switch on FrontRefresh Button Switch Utilities Diagnostics Trace Enables Read Button Enables Radio ButtonEnables All Button Trace Clear Button Enables None ButtonEnables Apply Button Enables Information Display WindowDisplay Read All Button Display Offset BoxDisplay Quantity Box Display Read ButtonEthernet Port Radio Button Switch Utilities SetupEthernet IP Address Box Use Sequence Checkbox Serial Port Radio Button Legacy Switches onlyCOMx Selection Box Legacy Switches only UDP Port # BoxFabric ID Switch Utilities Chassis ConfigurationChassis Number Rttov Stage Type Radio ButtonsApply Button Administration/Operation StatesSwitch Utilities Port Status Loop Devices Window 28Switch Management Switch Utilities Zoning Hard Zone Rules Broadcast Zone Rules Zoning Screen Switch Utilities Zoning Switch Utilities Name Server Switch Utilities Name Server Switch Utilities Management Configuration Snmp Configuration 38Switch Management Reset the Switch and the current Management firmware Managing the Switch Using Tftp Managing the Switch Using TftpTransfer a New Management Configuration File to the Switch SnmpReadCommunity SnmpLocation Loading New Switch Control Code into FlashLoading New Management Interface Flash 16-Port Switch only Reset the Switch Using Tftp Transfer the file to the Switch Retrieve the file from the Switch Network Management Managing the Switch Using SnmpFunction Description Network Management StationProperty Description Node AgentsTask Description Management Information Bases MIBsFuture use Polling-Only Data Collection Simple Network Management ProtocolTrap-Directed Polling Data Collection Interrupt-Based Data CollectionCommunity Type Description 16 Trap-Directed Polling Data CollectionFile Name Location and Description MIB II RFC 1213 Groups Management Information Base MIBMkii Utility MIB Configuring Snmp58Switch Management Power Supply Troubleshooting Diagnostics/TroubleshootingCorrective Action Power Supply/Fan TroubleshootingPower Supply Troubleshooting For example Power-On-Self-Test Post Power-On-Self-Test PostOverview 6Diagnostics/Troubleshooting Test/Failure Descriptions Heartbeat LED Blink PatternsProm Checksum Failure 1 Blink Gbic Bypass Port Loopback Test Failure 7 Blinks Switch Auto-Route Test Failure 10 Blinks Switch Management Port Failure 14 Blinks Continuous Test Continuous TestIs the Logic Power Good LED lit? ProcedureStep 14Diagnostics/Troubleshooting Did light shine through each fiber? Did this correct the problem?Fiber Continuity Tests Fiber Continuity TestDiagnostics/Troubleshooting Removal Input FuseFuses Amp Fuse Holder Input Fuse ReplacementGbic 4Removal/Replacement Procedures Port Connector Power Supply Power SupplyPower Supply Replacement Removal/Replacement Procedures Switch GigWorks MKII-16 Switch Model MKII-BASE16 Specifications2Reference Information Gb/s, even though backplanes Tftp TUV Longwave Laser Gbic single-mode Shortwave Laser Gbic multi-modeCopper Intra-Enclosure Gbic passive Copper Inter-Enclosure Gbic activeReference Information Front ViewDimensions in mm inches Reference Information Hardware Support Help DeskDescription Consists Contact UsFor supported software Ancor Customer Service Software SupportCustomer Responsibilities Appendix C Chassis Switch PanelForce Prom Mode Chassis Switch Panel ResetTest Mode Chassis Switch Panel Watch Dog Timer DisableBit Test Mode Area Fabric Stage