Chassis Switch Panel Reset, Force Prom Mode | Q-Logic MKII-BASE16

Chassis Switch Panel

Reset

Refer to Figure C-2.

RESET

Figure C-2 Reset Button

Use the Reset button only under the direction of your service representative.

Force PROM Mode

There may be circumstances when the control firmware, located in Flash memory, could be made incompatible with Switch operation (for example, through a failed Flash load operation) and yet the Flash Check Sum could be correct. If the Switch attempts to operate with the incompatible Flash Code, it could lock up and not allow a new Flash Burn operation.

Refer to Figure C-3. The Force PROM Mode switch causes the Switch to operate with control code stored in its PROM, and await the loading of new Flash code. Refer to the Diagnostics/Troubleshooting Section for how to load new Flash code.

The Force PROM Mode switch must be in the OFF position for normal Switch operation.

OFF

ON


Not Used				X4 FP
Not Used
Not Used						X3 WD


	Force PROM
	Force PROM
	Watch Dog
	Watch Dog

Figure C-3 Force PROM and Watch Dog Configuration Switches

C-2Chassis Switch Panel	GigWorks MKII-16 Switch Model MKII-BASE16
	59003-01 Rev. A	Installer's/User's Manual

Image 136

Q-Logic MKII-BASE16 user manual Chassis Switch Panel Reset, Force Prom Mode

Contents

GigWorks MKII-16 Switch Model MKII-BASE16 Release Number 01, Revision a December Table Of Contents Table Of Contents Switch Management Table Of Contents Diagnostics/TroubleshootingRemoval/Replacement Procedures Appendix B Ancor Customer Service List Of Figures Table Of Contents Appendix C Chassis Switch PanelList Of Tables How to Use This Manual Intended Audience Ancor Customer Service Related Materials Safety Notices Communications StatementsCommunications Statements Federal Communications Commission FCC Class a Statement CE Statement Communications Statements Vcci Class a Statement Laser Safety Information Laser Safety InformationCertification and Classification Information Laser Safety Information Optical GBICs Usage Restrictions Laser Safety Information Labeling Requirements Accessible Parts Pièces AccessiblesAccessible Parts Zugängliche Teile Table Of Contents GigWorks MKII-16 Switch Major Fibre Channel Port Features Major Switch Management Features General Description General Description Major Switch Chassis Features Fibre Channel Ports Chassis Front Typical Gbic General Description Front Panel Controls Front Panel LEDs Not used. OFF Chassis Back Refer to Figure Power Good Light Green Overheat Light Red Chassis Switch Panel Installation Unpack Shelf Mount Installation Place or Mount the EquipmentRack Mount Cabinet Mounting Bracket Install GBICs To IEC 825 1984 + Cenelec HD 482 S1 Installation Connect to AC Power Gefahr 6Installation Logic Power Good LED Check the Power-On-Self-Test Post Results Cable N or NLPort Adapters to the Switch TuningPorts Distance Incorrect Cabling NPort ConnectionsFiber Optic Connections Copper Connections 10Installation Cabling Operating the Switch GigWorks Mkii Switch Utilities Introduction Introduction Trivial File Transfer Protocol Tftp Simple Network Management Protocol Snmp Ethernet Cabling Ethernet Cabling Configuring the Switch Ethernet Port Configuring the Switch Ethernet PortConfiguring the Ethernet Port Using the Switch Utilities Configuring Multiple Switches Configuring the Ethernet Port Using Tftp Loading the Switch Utilities Getting Started Switch Utilities Using the Switch UtilitiesFileOpen FileSave FileExit FileSave AsHelpAbout Switch Utilities Management Information Configuration Group Tables Error Group TablesOperation Group Tables Account Group Table Port Field Group Select ListTable Select List Read Button Switch Utilities Flash Flash File Name Cancel Button or the Flash Load Fails Reset the Ancor GigWorks Mkii SwitchLoad Flash Flash Load Progress World Wide Name Switch Utilities VersionsVersion Information Switches on Back Switch on FrontRefresh Button Switch Utilities Diagnostics Trace Enables Read Button Enables Radio ButtonEnables All Button Enables None Button Enables Apply ButtonEnables Information Display Window Trace Clear Button Display Offset Box Display Quantity BoxDisplay Read Button Display Read All Button Ethernet Port Radio Button Switch Utilities SetupEthernet IP Address Box Serial Port Radio Button Legacy Switches only COMx Selection Box Legacy Switches onlyUDP Port # Box Use Sequence Checkbox Fabric ID Switch Utilities Chassis ConfigurationChassis Number Stage Type Radio Buttons Rttov Administration/Operation States Apply Button Switch Utilities Port Status Loop Devices Window 28Switch Management Switch Utilities Zoning Hard Zone Rules Broadcast Zone Rules Zoning Screen Switch Utilities Zoning Switch Utilities Name Server Switch Utilities Name Server Switch Utilities Management Configuration Snmp Configuration 38Switch Management Reset the Switch and the current Management firmware Managing the Switch Using Tftp Managing the Switch Using Tftp Transfer a New Management Configuration File to the Switch SnmpReadCommunity Loading New Switch Control Code into Flash SnmpLocation Loading New Management Interface Flash 16-Port Switch only Reset the Switch Using Tftp Transfer the file to the Switch Retrieve the file from the Switch Managing the Switch Using Snmp Network Management Network Management Station Function Description Node Agents Task DescriptionManagement Information Bases MIBs Property Description Future use Simple Network Management Protocol Polling-Only Data Collection Interrupt-Based Data Collection Trap-Directed Polling Data Collection 16 Trap-Directed Polling Data Collection Community Type Description File Name Location and Description Management Information Base MIB MIB II RFC 1213 Groups Configuring Snmp Mkii Utility MIB 58Switch Management Diagnostics/Troubleshooting Power Supply Troubleshooting Power Supply/Fan Troubleshooting Corrective Action Power Supply Troubleshooting For example Power-On-Self-Test Post Power-On-Self-Test PostOverview 6Diagnostics/Troubleshooting Heartbeat LED Blink Patterns Test/Failure Descriptions Prom Checksum Failure 1 Blink Gbic Bypass Port Loopback Test Failure 7 Blinks Switch Auto-Route Test Failure 10 Blinks Switch Management Port Failure 14 Blinks Continuous Test Continuous Test Is the Logic Power Good LED lit? ProcedureStep 14Diagnostics/Troubleshooting Did this correct the problem? Fiber Continuity TestsFiber Continuity Test Did light shine through each fiber? Diagnostics/Troubleshooting Input Fuse Removal Input Fuse Replacement Fuses Amp Fuse Holder Gbic 4Removal/Replacement Procedures Port Connector Power Supply Power Supply Power Supply Replacement Removal/Replacement Procedures GigWorks MKII-16 Switch Model MKII-BASE16 Specifications Switch 2Reference Information Gb/s, even though backplanes Tftp TUV Shortwave Laser Gbic multi-mode Longwave Laser Gbic single-mode Copper Inter-Enclosure Gbic active Copper Intra-Enclosure Gbic passive Front View Reference Information Dimensions in mm inches Reference Information Help Desk Description ConsistsContact Us Hardware Support For supported software Ancor Customer Service Software SupportCustomer Responsibilities Chassis Switch Panel Appendix C Chassis Switch Panel Reset Force Prom Mode Test Mode Chassis Switch Panel Watch Dog Timer DisableBit Test Mode Area Fabric Stage